ملخص المحتوى في الصفحة رقم 1
Tempest i5000PX S5380
///
Version 1.1
Copyright
Copyright © TYAN Computer Corporation, 2006. All rights reserved. No part of
this manual may be reproduced or translated without prior written consent from
TYAN Computer Corp.
Trademark
All registered and unregistered trademarks and company names contained in
this manual are property of their respective owners including, but not limited to
the following.
TYAN, Tempest i5000PX are trademarks of TYAN Computer Corporatio
ملخص المحتوى في الصفحة رقم 2
Table of Contents Check the box contents! 3 Chapter 1: Introduction 1.1 Congratulations…………………………………………………………… 5 1.2 Hardware Specifications………………………………………………… 5 Chapter 2: Board Installation 2.1 Board Image……………………………………………………………… 8 2.2 Block Diagram……………………………………………………………. 9 2.3 Board Parts, Jumpers and Connectors………………………………... 10 2.4 Tips on Installing Motherboard in Chassis…………………………….. 20 2.5 Installing the Processor(s)………………………………....................... 21 2.6 Installing t
ملخص المحتوى في الصفحة رقم 3
Check the box contents! 1x S5380 motherboard 1x 34-Pin floppy drive cable 1 x Ultra-DMA-133/100/66/33 IDE cable 3 x Serial ATA power cable 6 x Serial ATA Cable 1 x COM Port Cable 1 x S5380 user’s manual 1 x S5380 Quick Reference guide 1 x TYAN driver CD 1 x I/O shield 2 x CPU Back Plane If any of these items are missing, please contact your vendor/dealer for replacement before continuing with the installation process. 3
ملخص المحتوى في الصفحة رقم 4
4
ملخص المحتوى في الصفحة رقم 5
Chapter 1: Introduction 1.1 - Congratulations You have purchased one of the most powerful server solutions. The Tempest ® i5000PX (S5380) is a flexible Intel platform for multiple applications, based on ® Intel “Blackford” MCH and ESB2 chipsets. ® Designed to support Intel Dempsey/Woodcrest processors and max 16GB DDR2-533/667 FB-DIMM memory, and featured with integrated Dual Gigabit Ethernet LAN, PCI-Express, PCI/PCI-X 32/64bit PCI bus plus six serial ATA ports, the S5380 offers
ملخص المحتوى في الصفحة رقم 6
Expansion Slots BIOS •Two (x2) 64/133 PCI-X slots •Phoenix BIOS on 8Mbit Flash - One inversed PCIe x4 slot (w/ x8 ROM signals from ESB2) for risers, in- •Support APM 1.2, ACPI 1.0b st lined with the 1 PCI-X slot •Serial Console Redirect • Two (x2) PCI Express x16 slot •PXE via Ethernet, USB device (w/ x8 signals from Blackford boot MCH) •PnP, DMI 2.0, WFW 2.0 power •One (x1) PCI Express x8 slot (w/ management x4 signals from ESB2) •User-configurable hardware monitoring Integra
ملخص المحتوى في الصفحة رقم 7
Chapter 2: Board Installation You are now ready to install your motherboard. The mounting hole pattern of the Tempest i5000PX S5380 matches the SSI CEB v1.01 specification. Before continuing with installation, confirm that your chassis supports an SSI CEB v1.01 motherboard. How to install our products right… the first time The first thing you should do is reading this user’s manual. It contains important information that will make configuration and setup much easier. Here are so
ملخص المحتوى في الصفحة رقم 8
2.1- Board Image This picture is representative of the latest board revision available at the time of publishing. The board you receive may or may not look exactly like the above picture. 8
ملخص المحتوى في الصفحة رقم 9
2.2 - Block Diagram Tempest i5000PX S5380 Block Diagram 9
ملخص المحتوى في الصفحة رقم 10
2.3 - Board Parts, Jumpers and Connectors This diagram is representative of the latest board revision available at the time of publishing. The board you receive may not look exactly like the above diagram. 10
ملخص المحتوى في الصفحة رقم 11
Jumper Legend OPEN - Jumper OFF, without jumper cover CLOSED – Jumper ON, with jumper cover Jumper/Connector Function Onboard VGA Jumper J8 - Open: Enable VGA (Default) - Closed: Disable VGA J25 COM2 Header J27 Fan Connector (for barebone use only) J28 IPMB Connector Chassis Fan Connectors J7/J44/J68 J7: FAN1, J44: FAN3, J68: FAN2 CPU Fan Connectors J39/J40 J39: CPUFAN1 J40:CPUFAN0 J70 Chassis LCD Module Interface Header J76 IDE Connector nd J74 The 2 Front Panel Heade
ملخص المحتوى في الصفحة رقم 12
J8 USB1 J28 USB2 12
ملخص المحتوى في الصفحة رقم 13
USB1/USB2: Front Panel USB2.0 Connector Pin 1 USB PWR Pin 2 USB_N_FB Pin 3 USB_P_FB Pin 4 GND 1 Use these headers to connect to the USB devices. J8: Onboard VGA Jumper Enable the onboard ATI VGA function. Disable the onboard ATI VGA function J28: IPMB Connector Pin 1 IPMB Pin 2 GND 1 DATA Pin 3 IPMB Pin 4 NC CLK 13
ملخص المحتوى في الصفحة رقم 14
J47 J74 J25 14
ملخص المحتوى في الصفحة رقم 15
JP47: Clear CMOS Jumper Use this jumper when you forgot your system/setup 3 1 password or need to clear system BIOS setting. Normal How to clear the CMOS data (Default) - Power off system and disconnect power supply from AC source - Use jumper cap to close Pin_2 and 3 for 3 1 several seconds to Clear CMOS - Replace jumper cap to close Pin_1 and 2 Clear Reconnect power supply to AC source Power on system J25: COM2 Hea
ملخص المحتوى في الصفحة رقم 16
J79 J77 J70 J27 J27: FAN Connector (for barebone use only) Use these pin definitions to connect to the barebone fans. 13 1 Signal Pin Pin Signal CPU0-TACH 1 2 SYS4-TACH 3 4 2 CPU1-TACH SYS5-TACH 14 FAN3-TACH 5 6 SYS6-TACH FAN1-TACH 7 8 SYS7-TACH FAN2-TACH 9 10 SYS8-TACH GND 11 12 Key HMO- GND 13 14 FANPWM1 16
ملخص المحتوى في الصفحة رقم 17
J70: LCM Module Header Signal Pin Pin Signal +5V 1 2 SIN 6 2 Key 3 4 GND +5Vsb 5 6 SOUT 1 5 Use this header to connect the LCM module with system monitoring function. This header is reserved for barebone use. J79: SMDC Connector The SMDC connector allows you to connect with Tyan Server Management Daughter Card (SMDC). The S5380 supports Tyan SMDC M3291. See Appendix I for more information on SMDC. st J77: The 1 Front Panel Header st The 1 Front Panel Header is used
ملخص المحتوى في الصفحة رقم 18
J40 J39 J7 J68 J44 SATA 0/1/2/3/4/5 18
ملخص المحتوى في الصفحة رقم 19
J39/J40: CPU0/CPU1 Fan Connectors Use this header to connect the processor cooling GND fan to your motherboard to keep the system at 12V optimum performance levels. Ta c ho met e r PWM J39: CPUFAN1; J40: CPUFAN0 J68: Chassis Fan Connector Use this header to connect the chassis cooling GND fan to your motherboard to keep the system at 12V optimum performance levels. Ta c ho met e r PWM J68: FAN2 J7/J44: Chassis Fan Co
ملخص المحتوى في الصفحة رقم 20
2.4 - Tips on Installing Motherboard in Chassis Before installing your motherboard, make sure your chassis has the necessary motherboard support studs installed. These studs are usually metal and are gold in color. Usually, the chassis manufacturer will pre-install the support studs. If you are unsure of stud placement, simply lay the motherboard inside the chassis and align the screw holes of the motherboard to the studs inside the case. If there are any studs missing, you will know r
