ملخص المحتوى في الصفحة رقم 1
POWER INVERTER AND CHARGER
500 WATT / 800 WATT PEAK
93096
ASSEMBLY AND OPERATING INSTRUCTIONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at http://www.harborfreight.com
TO PREVENT SERIOUS INJURY,
READ AND UNDERSTAND ALL WARNINGS
AND INSTRUCTIONS BEFORE USE.
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight T
ملخص المحتوى في الصفحة رقم 2
Specifications IN TEM DESCRIPTIO Cs ontinuous Power 500 Watt Ps eak Power 800 Watt D) C Voltage 12 Volts Nominal DC (11-15 Volts possible Az C Voltage 120 Volts AC at 60 H As C Receptacles (2) Two 3-Prong, Polarized Outlet Is nverter Fuse 2 X 30 Amp Cg harger Fuse 10 Amps, 250 Volt, Fast-actin 1 3 1 D8 imensions / " L x 9 / " W x 3 / " H 4 8 4 Ws eight 7.4 lb In ndicators Green LED = power o Cp harging Rates 5/10 Am OF perating Temperature 14-113° A' C Power Cord 10 - Modified sine wave with ove
ملخص المحتوى في الصفحة رقم 3
5. Keep children away. Children must never be allowed in the work area. Do not let them handle machines, equipment, or extension cords. 6. Use the right inverter for the job. Do not attempt to force a small inverter or attachment to do the work of a larger industrial inverter. There are certain appli- cations for which this Inverter was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this Inverter and do not use this Inverter for a purpo
ملخص المحتوى في الصفحة رقم 4
18. Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radia- tors, ranges, and refrigerator enclosures during installation. Connect all wires securely. Store metal objects away from the inverter. 19. People with pacemakers should consult their physician(s) before using this product. Electromagnetic fields in close proximity to a heart pacemaker could cause interference to or failure of the pacemaker. 20. Keep the Inverter well-ventilated. Do not place any
ملخص المحتوى في الصفحة رقم 5
BACK Negative Positive Charger Ground AC Input Terminal Charger Fuse Holder WARNING! Risk of Fire! The positive battery terminal connection must be the LAST connection and must be done with the inverter’s switch off. Connection For the power Inverter to work properly, your power source must provide 12 volts DC, and enough current (i.e., 32 amps to operate a load of 384 Watts or under). Warning: This Inverter must only be connected to batteries with a nominal out- put voltage of 12 volts. More v
ملخص المحتوى في الصفحة رقم 6
FRONT Indicators Power Switch Charge Current Switch Outlets Operation Powering AC Appliances 1. Plug the 115 VAC device(s) you wish to power into the 3-prong AC Receptacles. See FRONT above. The appliance(s) must not use more than 500 (total) watts during continuous operation, otherwise it may overload the Inverter. Warning: Some rechargeable appliances may damage the Power Inverter or the appliance. When first using a rechargeable device, check the Inverter’s tem- perature for the first 10 min
ملخص المحتوى في الصفحة رقم 7
Maintenance 1. Keep this unit clean and dry. Unplug before cleaning. Clean only the outside of this unit with a soft, dry cloth; never clean this unit with water or cleaners. 2. Aside from the fuse, this device does not contain any user replaceable parts. If it needs service, take it to a qualified technician. BEFORE INSPECTING THE FUSES, MAKE SURE THAT THE UNIT HAS HAD AMPLE TIME TO COOL WITH NO LOAD. 3. Charger Fuse Replacement a. If the Inverter stops functioning in Charger mode, the charg
ملخص المحتوى في الصفحة رقم 8
Troubleshooting Tips 1. If the low battery alarm sounds, this means that the input voltage is below the necessary 11 V. The battery needs recharging. You should stop using the appli- ance and then recharge the battery. If this is not done, the Inverter will shut off automatically at around 10 V. 2. If you are unsure if the Inverter will have the proper amount of current to run the device, use this rough guideline: Take the power consumption of the load in watts and divide it by 12 (input vol
