ملخص المحتوى في الصفحة رقم 1
High End Residential
In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Adult Assembly Required.
This manual, accompanied by sales receipt, should be saved and kept on hand as a convenient reference, as it contains
important information about your model.
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND OPERATOR'S
MANUAL BEFORE USING THIS UNIT.
FAILURE TO FOLLOW OPERATING
INSTRUCTIONS COULD RESULT IN
INJU
ملخص المحتوى في الصفحة رقم 2
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN WARNING SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. Read and understand warnings listed below before using this product. Owner must ensure that all players know and follow these rules for safe operation of the system. Failure to follow these warnings may result in serious injury and/or property To ensure safety, do not attempt to assemble this system without following damage. the instructions carefully. Proper and complete
ملخص المحتوى في الصفحة رقم 3
PARTS LIST Item Qty. Part No. Description 1 1 968880 Pole 2 1 908266 Tube, Ground Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 205702 Nut, Hex, 3/8-16 6 4 203300 Washer, Locking, 3/8 7 4 205700 Bolt, Hex, 3/8-16 x 3.5” Long 8 1 204922 Pin, Hitch 9 1 204923 Pin, Cotter, #8 10 3 204993 Rebar, .5” diameter, 18” Long ID# 516000 06/05 11 1 516000 Label, Height Adjustment 12 1 204940 Screw Jack 11 13 1 Backboard 14 1 80854501 Rod, Threaded Assembly, 5/8-11 x 19.8”, Zinc 15 1 204921 Washer, Barrel 16
ملخص المحتوى في الصفحة رقم 4
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #23 (2) Item #20 (1) Item #29 (4) Item #7 (4) Item #28 (2)* Item #34 (4) HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) Item #33 (2)* Item #6 (4) Item #27 (4)* Item #21 (16) Item #24 (9) Item #5 (4) Item #22 (9)* Item #25 (4) Item #26 (1) HARDWARE IDENTIFIER (OTHER-NOT ACTUAL SIZE) Item #9 (1) Item #15 (1) Item #19 (26) Item #8 (1) ID# M88604C1 08/06 4
ملخص المحتوى في الصفحة رقم 5
Ensure ground is level with playing surface, then dig pole hole. 1. 24" (61 cm) 48" (121.9 cm) WARNING! 24" (61 cm) GROUND SURFACE PLAYING SURFACE 48" (121.9 cm) CONTACT UTILITIES BEFORE DIGGING. Install nuts (25) onto the ground tube bolts as shown. 2. 25 NOTE: Nuts on the top of the plate are used for leveling the pole after system is 2 fully assembled. 08/06 ID# M88604C1 5
ملخص المحتوى في الصفحة رقم 6
Fill hole with concrete. Tamp down concrete to release air pockets 3. and build drainage hill. DRAINAGE HILL 1" (2.54 cm) PLAYING SURFACE SIDE VIEW 4. Insert rebar (10) through holes in ground tube assembly (2) as shown. 2 10 10 10 ID# M88604C1 08/06 6
ملخص المحتوى في الصفحة رقم 7
Insert ground tube assembly (2) into cement as shown. Move assembly around to release any air 5. pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to level mounting plate on top of drainage hill. Level mounting plate and square with playing surface. Clean off any excess cement on mounting plate at this time and place washers (24) on mounting bolts (19). 2 10 IMPORTANT! NOTE ORIENTATION 10 Front of mounting plate (2) must be parallel with playing 10 surf
ملخص المحتوى في الصفحة رقم 8
Insert bushings (19) into areas shown. 6. 13 19 19 19 19 19 19 19 19 19 19 19 19 19 19 1 17 19 19 19 19 18 19 19 19 ID# M88604C1 08/06 8
ملخص المحتوى في الصفحة رقم 9
Rest top of pole on a piece of scrap wood (not included) and line up holes in pole (1) to holes in 7A. mounting plate (2) as shown. 1 WARNING! PLAYING SURFACE THREE CAPABLE ADULTS SCRAP WOOD REQUIRED FOR THIS (NOT INCLUDED) PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 1 2 PLAYING SURFACE Insert bolt (23) through holes in plate and pole and secure with nut (22). 7B. 1 23 22 08/06 ID# M88604C1 9
ملخص المحتوى في الصفحة رقم 10
8. WARNING! TWO people are required to lift pole into position so that the threaded assembly rod (14) can be installed and secured by the THIRD person. While pole is being supported by TWO THREE CAPABLE ADULTS REQUIRED FOR THIS capable adults, position rod (14) and lock PROCEDURE. FAILURE TO into place with hitch pin (8) and cotter pin FOLLOW THIS WARNING (9). COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Slide barrel washer (15) onto other end of rod (14) and secure with washer (24) a
ملخص المحتوى في الصفحة رقم 11
9. While still in forward position, attach both upper and lower yokes (17 & 18) to pole as shown. WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 22 21 17 18 21 28 08/06 ID# M88604C1 11
ملخص المحتوى في الصفحة رقم 12
Attach elevator adjustment (12) to 10. lower yoke (18). WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 22 18 21 19 12 19 21 20 ID# M88604C1 08/06 12
ملخص المحتوى في الصفحة رقم 13
Attach elevator adjustment (12) to pole bracket. 11. WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 21 21 23 22 33 33 12 08/06 ID# M88604C1 13
ملخص المحتوى في الصفحة رقم 14
Attach backboard (13) to upper and lower 12. yokes (18 & 17). Then, hinge board to match up with holes in B. A. First attach board (13) to upper yoke (17), lower yoke (18), FIG. C, and secure with using TWO people to hold the board and hardware as shown in FIG. D. ONE person to attach hardware (FIG. A). Use hardware as shown in FIG. B. WARNING! THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. FIG. A FIG. C FI
ملخص المحتوى في الصفحة رقم 15
Before starting rim assembly, tighten nut (26) until it is positioned 6-3/4” from 13. the end of the rod as shown (Figure A). Remove rim cover (16), attach rim assembly (3) to backboard (13) and reattach rim cover (16). ** For rim assembly, see instructions included with rim. IMPORTANT! Carefully cut and peel protective film away from 14 board prior to attaching rim. 26 FIGURE A. 5 6 13 Rim Assembly 16 3 Refer To Instructions 27 Included With Rim 27 Hardware For Rim Assembly. 7 7 08/06 ID# M886
ملخص المحتوى في الصفحة رقم 16
10 9 87 14. Set-up For Left Side Set-up For Right Side Apply height indicator A. 30 30 labels (32 & 31) to height indicators (30). 10 10 9 7 9 8 7 8 31 10 10 32 7 9 8 9 8 7 Attach height indicators to lower yoke in area shown by turning B. screws (29) into place with a phillips-head screwdriver. IMPORTANT! 29 NOTE ORIENTATION OF HEIGHT INDICATORS: 10’ MARK SHOULD FACE AWAY FROM BACKBOARD. Attach height indicators C. to lower yoke in area shown by turning screws (29) into place 29 with a phillip
ملخص المحتوى في الصفحة رقم 17
16. Upright pole (1) by tightening nut (26). WARNING! Using 15/16” wrench, turn nut (26) clockwise to begin standing pole upright. Continue to turn nut (26) THREE CAPABLE ADULTS REQUIRED FOR THIS PROCEDURE. TWO PEOPLE ARE REQUIRED TO until pole has come to rest against washers (24) and GUIDE AND SUPPORT THE SYSTEM WHILE THE pole is vertical. THIRD PERSON IS TIGHTENING NUT (26) TO RAISE THE SYSTEM UPRIGHT. Once pole is in its final position, install washers (24) FAILURE TO FOLLOW THIS WARNING CO
ملخص المحتوى في الصفحة رقم 18
After pole has been secured to the anchor plate (2) loosen nut (26), 17. remove cotter pin (9), and pull out pin (8). This will allow the removal of the assembly rod (14) which is no longer necessary for the remainder of the assembly and installation of system. WARNING! ONLY AFTER THE ANCHOR PLATE HAS BEEN FULLY TIGHTENED: Remove cotter pin (9) and pin (8) to remove threaded assembly rod (14) from anchor plate (2). 26 24 15 14 9 8 25 ID# M88604C1 08/06 18
ملخص المحتوى في الصفحة رقم 19
Check system leveling. Pole (1) 18. should be level in all directions. After system is leveled, completely tighten all nuts (25). NOTE: If adjustment is necessary, adjust system by rotating 1 the nuts (25) between anchor plate (2) and pole flange. 25 2 19. Apply height adjust ment label (11). Adjust system by turning crank until desired height is reached per height indicator (30). 30 WARNING! 10 feet 12 (3.05 m) 11 READ AND UNDERSTAND WARNING & HEIGHT ADJUSTMENT LABELS BEFORE USING THIS UNIT. F
ملخص المحتوى في الصفحة رقم 20
LIMITED LIFETIME WARRANTY ® Subject to proper installation and normal use, Spalding warrants, subject to limitations below, to the original retail ® purchaser all structural components of the Spalding system to be free of defects in material and workmanship for the duration of ownership by the original retail purchaser. Merchandise must be shipped prepaid with a copy of proof of purchase to our factory for examination to see whether it needs to be repaired or replaced. Any labor costs, travel e
