ملخص المحتوى في الصفحة رقم 1
240 VOLT COMPRESSOR
4 HP PEAK – 29 GALLON
OiL-LubRiCATEd
Model 92504
ASSEMbLY ANd OPERATiNG iNSTR uCTiONS
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our Web site at: http://www.harborfreight.com
© ®
Copyright 2005 by Harbor Freight Tools . All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions, please call 1-800-444-3353.
COVER REViSEd 02/0
ملخص المحتوى في الصفحة رقم 2
PROduCT SPECiFiCATiONS 240 V~ / 60 Hz / Single Phase / 4 HP Peak / Motor 3 HP Working / 3,400 RPM / 9 Load Amps / Two Capacitor (Run & Start) Overload Reset Button 15 Amp 12 Gauge, 3-Wire (Stripped), 20 Ft. Long Power Cord 240 Volt Power Cord Plug Not Included. Air Tank Capacity 29 Gallons 16.4 @ 40 PSI / 15.7 @ 70 PSI / CFM Airflow 14.5 @ 90 PSI / 13.0 @ 115 PSI Compressor Pump Type Dual V-Head Cylinder / Belt Driven Safety Valve Setting 120 PSI Air Pressure Gauge Indicators 0-200 PSI in 5 PSI
ملخص المحتوى في الصفحة رقم 3
2. do not operate compressors in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Compressors create sparks which may ignite the dust or fumes. 3. Keep bystanders, children, and visitors away while operating a compressor. Provide barriers or shields as needed. ELECTRiCAL SAFETY 1. Grounded compressors must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the
ملخص المحتوى في الصفحة رقم 4
6. use safety equipment. Always wear eye protection. Make sure you are wearing your protective clothing, safety glasses with side shields and dust mask or air respirator, if appropriate. TOOL uSE ANd CARE 1. do not force the compressor. use the correct compressor for your application. The correct compressor will do the job better and safer at the rate for which it is designed. Never attempt to force the compressor to provide more pressure than it was designed for. 2. do not use the comp
ملخص المحتوى في الصفحة رقم 5
SPECiFiC SAFETY RuLES 1. CAuTiON! Prior to its first use, and thereafter prior to each subsequent use, make sure to fill the Air Compressor with a premium quality, 30 weight, non- detergent oil to the specified level. Running the Air Compressor with no oil or with low oil will cause damage to the equipment and void its warranty. Refer to the “Operating Instructions” section for details on filling the Air Compressor with oil. 2. When filling the Air Compressor with oil, make sure to unscrew
ملخص المحتوى في الصفحة رقم 6
parts when the unit is connected to electrical power. Always have compressor safety guards in place before turning compressor on. 13. use approved air hose. Never use plastic or PVC pipe (unless specified for Air Compressors) to carry air under pressure. Regardless of its pressure rating, it can burst under pressure. Use only metal pipe. 14. Never plug the power cord of this product into an electrical outlet while standing on a wet or damp surface. 15. THiS AiR COMPRESSOR MAY REqui RE A dEdi
ملخص المحتوى في الصفحة رقم 7
SYMbOLOGY To extend the life of your air tools and equipment, we recommend installing an oiler and water filter in series with the Air Outlet Valves (4) of the Air Compressor. (See Figure C.) AiR TO COMPRESSOR TOOL OR OiLER WATER EquiPMENT FiLTER FiGuRE C ASSEMbLY iNSTRuCTiONS To Attach A Power Cord Plug: The Power Cord (31) requires the attachment of a 240 volt, grounded, 3-Prong Plug (not included). For safety purposes, only a qualified, certified, electrician should attach a Plug to t
ملخص المحتوى في الصفحة رقم 8
outlet that is properly grounded. To Attach Quick Connectors: Prior to use, the Air Compressor requires the attachment of a 1/4” NPT Quick Connector (not included) to each of its two Air Outlet Valves (4). To do so, wrap approximately 4” of pipe thread sealant tape (not included) around the male threads of the Quick Connectors. Then, firmly screw the Quick Connectors into the Air Outlet Valves. (See Figure d.) To Fill The Air Compressor With Oil: 1. CAuTiON! Prior to its first
ملخص المحتوى في الصفحة رقم 9
3. Once the Oil Fill Cap (28) is removed, fill the Air Compressor with a premium quality, 30 weight, non-detergent oil until the level of the oil rises to the midway point in the Oil Level Indicator (35). Then, screw the Oil Fill Cap back onto the Oil Fill Hole. (See Figure d.) To Mount The Air Compressor: 1. For added safety, it is recommended that the Air Compressor be mounted on a flat, level, sturdy, concrete floor surface capable of withstanding the weight of the Air Compressor and a
ملخص المحتوى في الصفحة رقم 10
6. If using only one of the two Air Outlet Valves (4), attach an air hose (not included) to the Air Outlet Valve. Then, attach the other end of the air hose to the pneumatic tool that will be used. If using both Air Outlet Valves simultaneously, attach an air hose to each Air Outlet Valve. Then, attach the other ends of the air hoses to their respective pneumatic tools. (See Figure E.) To Start The Air Compressor: 1. Plug the Power Cord Plug (31) into the nearest 220 volt, grounded, elec
ملخص المحتوى في الصفحة رقم 11
5. Check to make sure the pneumatic tools that will be used are turned off and properly connected to their air hoses. 6. Once the Pressure Gauge (5) has reached at least 80 PSI, turn the Lever on the Air Outlet Valve (4) forward to its open position in order to supply air to the pneumatic tool. If both Air Outlet Valves are being used, turn both Levers forward to their open positions. (See Figure E.) 7. iMPORTANT: Both Pressure Gauges (5) should always indicate the same PSI reading, mean
ملخص المحتوى في الصفحة رقم 12
To Turn Off The Air Compressor: 1. When finished using the Air Compressor, press down on its Power Switch (9) to turn off the unit. (See Figure E.) 2. Disconnect the Power Cord Plug (31) from its electrical outlet. 3. Turn on the pneumatic tools to expend all remaining compressed air from the Air Compressor, air hoses, and pneumatic tools. 4. Turn the Pressure Adjustment Knob (6) counterclockwise all the way to its “OFF” position. (See Figure E.) 5. Turn each Lever on the two Air Outlet Val
ملخص المحتوى في الصفحة رقم 13
4. NOTE: Each time the Oil Fill Cap (28) is removed, observe the PCV Filter (41) that is located inside the Oil Fill Cap. When necessary, remove the PCV Filter and clean with a mild solvent. Allow the PCV Filter to dry. Then, replace the PCV Filter in the Oil Fill Cap, and screw the Oil Fill Cap back onto the oil fill hole. (See Figure F.) PCV FiLTER (41) OiL FiLL HOLE OiL FiLL CAP (28) FiGuRE F 5. Weekly: The Air Compressor is equipped with two Air Filters (38) which should be cle
ملخص المحتوى في الصفحة رقم 14
6. To replace the V-belt: The Air Compressor is equipped with a V-Belt (size: A1168 Li). To replace the V-Belt, remove the four Nuts (24) and four Flat Washers (23) on the Outer Guard Screen (25). Next, remove the three Clips (34) located at the top of the Outer Guard Screen. Then, remove the Outer Guard Screen. (See Figure H.) OuTER Gu ARd CLiP CLiP CLiP SCREEN (34) (34) (34) (25) LARGE V-bELT MOTOR bELT WHEEL (27) PuLLEY (14) NuT (24) NuT (24) FiGuRE H FLAT WASHER (23) FLAT WASHER (23)
ملخص المحتوى في الصفحة رقم 15
8. Remove the loose V-Belt (27) from the Large Belt Wheel and Motor Pulley (14). (See Figure H.) 9. Install a new V-Belt (27) on the Large Belt Wheel and Motor Pulley (14). (See Figure H.) 10. Slide the Motor (14) back toward its original position to tighten the tension on the V-Belt (27). NOTE: To determine the proper tension on the V-Belt, with your index finger press down on the V-Belt. The V-Belt should deflect downward about 3/4”. If necessary move the Motor Pulley (14) toward or a
ملخص المحتوى في الصفحة رقم 16
PARTS LiST Part description qty. Part description qty. 1 Flat Washer (8) 4 22 Screw (M5x16) 5 2 Screw (M8x16) 4 23 Flat Washer (5) 5 3 Safety Release Valve 1 24 Nut (M5) 5 4 Air Outlet Valve 2 25 Outer Guard Screen 1 5 Pressure Gauge 2 26 Inner Guard Screen 1 6 Pressure Adjustment Knob 1 27 V-Belt (A1168 Li) 1 7 Connector 2 28 Oil Fill Cap 1 8 Top Cover 1 29 Head Assembly 1 9 Power Switch 1 30 Screw (M8x16) 1 10 Screw (M8x25) 4 31 Power Cord 1 11 Spring Washer (8) 8 32 Air Tank 1 12 Flat Washer
ملخص المحتوى في الصفحة رقم 17
ASSEMbLY diAGRAM 34 23/24 25 20 26 19 27 18 21/22/23/24 17 16 9 28/41 15 5 8 29 30 3 2 14 6 11/12/13 7 4 1 10/11/12/13 36/37/38/39 35 40 31 32 33 NOTE: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. SKU 92504 For technical questions, please call 1-800-444-3353. Page 17
ملخص المحتوى في الصفحة رقم 18
WiRiNG diAGRAM REV 05/06 SKU 92504 For technical questions, please call 1-800-444-3353. Page 18
