ملخص المحتوى في الصفحة رقم 3
Table of CT on T en s Refrigerator Safety .......................................................................1 Unpack Refrigerator ....................................................................9 Design Specifications ...............................................................2-6 Anti-tip Blocking ..........................................................................9 Product Dimensions ....................................................................2 Water Line Connection
ملخص المحتوى في الصفحة رقم 4
d esign s PC e C ifi a Tions PRCT odu d imensions ◊ The depth from the front of the top grill (w/o decorator panel) to the back of the refrigerator chassis is 25 1/4” (641mm). ◊ The depth from the rear of the top grill to the back of the refrigerator chassis is 23 13/16” (605mm). ◊ The power cord is 40” (1016mm) long. ◊ The height from the top of the top grill to floor with the leveling legs in the down position is 83 3/8” (2118mm) ◊ The height from the top
ملخص المحتوى في الصفحة رقم 5
d esign s PeCifiCa Tions CusT om o veRyla Panels (A) The decorator panels for overlay models cover the door trim for H Grille Panel an attractive, seamless look that flows into the overall design of the room. This application is often accomplished by using three panels: the decorative front panel, a spacer panel of .10-inch thickness, and a 1/4-inch backer panel. (see page 4) W W W (B) Dispenser Freezer Panel H (C) (D) Non-Dispenser Refrigerator Freezer Panel Panel H H2 H1 W1 W2 W
ملخص المحتوى في الصفحة رقم 6
d esign s PC e C ifi a Tions Overlay Panel Specifications NOTES: (See Illustrations on page 3.) ◊ Use counter sink screws for attaching the backer panel to the front panel. 42-Inch Model 48-Inch Model ◊ On 42” custom panels watch location of handle mounting BACKER PANEL due to under cut of front panel. (A) Grille Panel ◊ For freezer dispenser front panels, remove fountain trim W Width 40 1/4” (1022mm) 46 1/4” (1175mm) and tape to the backside of the backer panel. Note recycle symbol should b
ملخص المحتوى في الصفحة رقم 7
d esign s PeCifiCa Tions Custom Toe Kickplate Specifications ® If using custom toe kickplate with your Dacor Built-In Refrigerator, refer to the following specifications. Angled cut for thicker plates Panel thicker than 3/16" 6 1/4" 5 5/8" 15/16" Typ 4 13/16" (A) 7/8" (A) (A) Cut out for Dispenser (B) (B) (B) (B) 3 3/4" 5/16" 3" 2 3/16" Typ R. 1/2" 1 13/16" Allow relief here for 3/4" Typ dispenser models with panels thicker than 3/16" 1 1/8" Typ “C” Model Hole “A”Dia. Hole “B”Dia. Overall Lengt
ملخص المحتوى في الصفحة رقم 8
d esign s PeCifiCa Tions 90° Door Stop 90˚ Door Opening (Top View) Both doors are designed to open 135°. To restrict one or both doors to a 90° opening, use the door stops supplied in this kit. Cabinet Trim 23 7/8" to Rear of Cabinet Door Closed 0" 1/4" 1/2" 3/4" Door 1" Panel 1 1/4" 1 1/2" 1 3/4" 2" 2 1/4" 2 1/2" Door Open 2 3/4" 3" @ 90˚ 3 1/4" 3 1/2" Lower Hinge Plate 3/4" Overlay Panel Door Stop Mounting Hole 90° Door Stop With the doors closed, screw a door stop into the underside of the
ملخص المحتوى في الصفحة رقم 9
i nsT alla Tion s PeCC ifi a Tions Tools and PaRTs l C o a Tion RequiRemenTs ® Your Dacor refrigerator can be recessed in an opening between IMPORTANT: cabinets or installed at the end of a cabinet run using a side panel ◊ Installer: Leave these Installation Instructions with the to enclose the refrigerator. homeowner. WARNING ◊ Homeowner: Keep these Installation Instructions for future ExPLOSION HAzARD – Keep flammable material and vapors, reference. Save these Installation Instructions f
ملخص المحتوى في الصفحة رقم 10
i T ns alla Tion s PC e C ifi a Tions Rough-In Dimensions e CTR le iCal RequiRemenTs ◊ The solid sofit or ceiling should be within 1” (25mm) above WARNING the refrigerator. If the solid sofit is higher than 1” (25mm) or ELECTRICAL SHOCK HAzARD – Plug into a grounded 3- one is not available, then the refrigerator must be braced to prong non-GFCI outlet. Do not remove ground prong. Do not prevent tipping during use. If the anti-tip blocking is need. use an adapter. Do not us an extension cor
ملخص المحتوى في الصفحة رقم 11
i nsT alla Tion i TR ns uCTions u nP aCk RefRigeRa TR o a nTi -TP i b loCking Blocking the Refrigerator WARNING If there is a solid sofit or ceiling above the unit and the clearance TIP OvER HAzARD – Refrigerator is top heavy and tips easily is 1” (25mm) or less you will not need to block the unit. For when not completely installed, Keep doors taped closed until installations with clearances of more than 1” (25mm), you must refrigerator is completely installed. Use two or more people to u
ملخص المحتوى في الصفحة رقم 12
i nsT alla Tion i nsTRuCTions l evel u niT w a TR e l ine ConneCTion ◊ Slide the unit in place and raise the front and rear levelers ◊ Before attaching the copper tubing to the unit, flush at least until the unit touches the brackets. (Use a 3/8” socket to 2qt (1.9L) of water through the copper tubing into a bucket to raise and lower the unit.) get rid of any particles in the water line. ◊ Check to see whether the refrigerator is level left to right, by ◊ Check for leaks around the saddle v
ملخص المحتوى في الصفحة رقم 13
i nsT alla Tion i nsTRCT u ions Panel Installation for Dispenser Models i T ns all CT us om Panels 1. Power switch needs to be off. Switch located in machine Panel Installation compartment area (see User Guide). Before you begin installing panels, refer to the “Custom Panel Specifications” for overlay models and verify that you are working 2. Remove magnetic strip on door trim. Use of tape may be with the panel design called for in your installation. If you have required removing the magnet
ملخص المحتوى في الصفحة رقم 14
i nsTTion alla i nsTRuCTions 7. Remove the four #15 Terminals Torx plastic collar screws from the fountain/escutcheon collar. Control Panel 7 8. Place the fountain/ escutcheon collar onto Stainless Steel Splashguard the backer panel. Use tape to hold in place. Spill Tray Grille 8 CAUTION 9. Open the freezer door WARNING – Do not exceed the panel dimensions shown in the chart on and slide panel onto page 4 for the grille panel. If the decorator panel is larger than specified, it may res
ملخص المحتوى في الصفحة رقم 15
i nsT alla Tion i nsTRuCTions Side Panel Installation 1/4" side panel fitted up to 1/4" side panel fitted up to ® the cabinet trim (top view) the cabinet trim (top view) If using side panels with the Dacor Built-In Refrigerator, on Freezer side. on Refrigerator side. they will need to be 1/4-inch thick. Slide the panel into position and secure with screws indicated by the shaded Backside of Unit Backside of Unit area. A 3/16-inch spacer is required between the cabinet and side panel. A 1/2-i
ملخص المحتوى في الصفحة رقم 16
i T ns alla Tion i nsTRuCTions i nsT alla Tion CheCklisT The importance of the proper installation of your Dacor Built-In Refrigerator cannot be overemphasized. Proper installation is the responsibility of the homeowner. IMPORTANT: To ensure a safe and proper installation, the following checklist should be competed by the installer to ensure that no part of the installation has been overlooked. Any questions or problems with this installations should be ® ® directed to your Dacor dealer or
ملخص المحتوى في الصفحة رقم 17
n oTes
ملخص المحتوى في الصفحة رقم 18
n oTes
ملخص المحتوى في الصفحة رقم 19
ملخص المحتوى في الصفحة رقم 20
The information and images in this book are the copyright property of Distinctive Appliances, Inc. Neither this book nor any information or images contained herein may be copied or used in whole or in part without the express written permission of Distinctive Appliances, Inc. Web Site: www.dacor.com Phone: (800) 793-0093 ©Distinctive Appliances, Inc. all rights reserved.
ملخص المحتوى في الصفحة رقم 1
Installat Ion Instruct Ions
Bu Ilt -In r efr Igerators
Part No. 100500 Rev. A
ملخص المحتوى في الصفحة رقم 2
