ملخص المحتوى في الصفحة رقم 1
Electronic Disc
Sander
180 mm (7”)
MODEL GV7000C
003426
DOUBLE
INSULATION
INSTR U CTION MANU AL
WARNING:
For your personal safety, READ and UNDERSTAND before using.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
www.makitatools.com
ملخص المحتوى في الصفحة رقم 2
SPECIFICATIONS Model GV7000C Abrasive disc diameter 180 mm (7”) No load speed (RPM) 2,500 - 4,700/min. Overall length 210 mm (8 - 1/4”) Net weight 2.0 kg (4.4 lbs) Spindle thread 5/8” • Manufacturer reserves the right to change specifications without notice. Specifications may differ from country to country. GENERAL SAFETY RULES USA002-2 (For All Tools) WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or seri
ملخص المحتوى في الصفحة رقم 3
5. Avoid body contact with grounded sur- 14. Use safety equipment. Always wear eye faces such as pipes, radiators, ranges and protection. Dust mask, non-skid safety refrigerators. There is an increased risk of shoes, hard hat, or hearing protection must electric shock if your body is grounded. be used for appropriate conditions. Ordinary eye or sun glasses are NOT eye protection. 6. Do not expose power tools to rain or wet conditions. Water entering a power tool will Tool Use and Care increase t
ملخص المحتوى في الصفحة رقم 4
24. When servicing a tool, use only identical SERVICE replacement parts. Follow instructions in 23. Tool service must be performed only by the Maintenance section of this manual. qualified repair personnel. Service or main- Use of unauthorized parts or failure to follow tenance performed by unqualified personnel Maintenance instructions may create a risk of could result in a risk of injury. electric shock or injury. USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. W
ملخص المحتوى في الصفحة رقم 5
cause loss of control leading to personal 11. Do not touch the workpiece immediately injury. after operation; it may be extremely hot and could burn your skin. 6. Hold the tool firmly. 12. Check that the workpiece is properly sup- 7. Keep hands away from rotating parts. ported. 8. Make sure the abrasive disc is not con- 13. Pay attention that the wheel continues to tacting the workpiece before the switch is rotate after the tool is switched off. turned on. 14. This tool has not been waterproofed
ملخص المحتوى في الصفحة رقم 6
FUNCTIONAL CAUTION: DESCRIPTION • Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003407 Switch action CAUTION: • Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the “OFF” 1 position when released. 2 • Switch can be locked in “ON” position for ease of operator comfort during extended use. Apply caution 1. Switch trigger when locking tool in “ON” position and maintain firm 2. L
ملخص المحتوى في الصفحة رقم 7
The tool equipped with electronic function are easy to oper- ate because of the following features. • Electronic constant speed control Possible to get fine finish, because the rotating speed is kept constantly even under the loaded condition. • Soft start feature Soft start because of suppressed starting shock. ASSEMBLY CAUTION: • Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003412 Installing side grip (auxiliary handle) & cover CAUTION: •
ملخص المحتوى في الصفحة رقم 8
003414 Installing or removing abrasive disc 1 Mount the rubber pad onto the spindle. Fit the abrasive disc 2 on the rubber pad and screw the lock nut onto the spindle. 3 4 1. Lock nut 2. Abrasive disc 3. Rubber pad 4. Spindle 003418 To tighten the lock nut, hold the spindle with the wrench so 1 that it cannot revolve, then use the lock nut wrench and securely tighten clockwise. 2 To remove the disc, follow the installation procedure in reverse. 1. Lock nut wrench 2. Wrench OPERATION 003421 Sandi
ملخص المحتوى في الصفحة رقم 9
001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Replace when they wear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brushes should be replaced at the same time. Use only iden- tical carbon brushes. 1 1. Limit mark 003423 Use a screwdriver to remove the brush holder caps. Take out 1 the worn carbon brushes, insert the new ones and secure the brush holder caps. 2 To maintain product SAFETY and RELIABILITY, repairs
ملخص المحتوى في الصفحة رقم 10
Memo 10
ملخص المحتوى في الصفحة رقم 11
Memo 11
ملخص المحتوى في الصفحة رقم 12
Memo 12
ملخص المحتوى في الصفحة رقم 13
First-Class Postage Required Post Office will not deliver without proper postage. Makita U.S.A., Inc. 14930 Northam Street La Mirada, CA 90638-5753 Fold 13 Cut
ملخص المحتوى في الصفحة رقم 14
MAIL THIS PORTION Your answers to the following questions are appreciated. 1. This product was purchased from: 3. How did you learn about this product: Home Center Other ( ) Magazine Radio Hardware/Lumber Store From Dealer Exhibition Tool Distributor Newspaper From Friend Industrial Supply Store Display Previous Usage Construction Supply Catalog Other ( ) 2. Use of the product is intended for: 4. Most favored points are: Construction Trade Design Repair Se
ملخص المحتوى في الصفحة رقم 15
FACTORY SERVICE CENTERS 1-800-4-MAKITA RETAIN THIS PORTION FOR YOUR RECORDS ARIZONA FLORIDA MISSOURI PENNSYLVANIA 3707 E. Broadway Rd., Ste. 6 750 East Sample Road 9876 Watson Road 1704 Babcock Blvd. Phoenix, AZ 85040 Pompano Beach, FL 33064 St. Louis, MO 63126-2221 Pittsburgh, PA 15209 (602) 437-2850 (954) 781-6333 (314) 909-9889 (412) 822-7370 CALIFORNIA GEORGIA NEBRASKA PUERTO RICO 41850 Christy St. 4680 River Green Parkway NW 4129 S. 84th St. 200 Guayama St. Fremont, CA 94538-5107 Duluth,
ملخص المحتوى في الصفحة رقم 16
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • lead from lead-based paints, • crystalline silica from bricks and cement and other masonry products, and • arsenic and chromium from chemically-treated lumber. Your risk from these exposures varies, depending on how often you do this type of
