Audiovox SP-6CD دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

INSTALLATION MANUAL
SP-6CD
6 - DISC CD CHANGER SYSTEM
MODELSP-6CD

ملخص المحتوى في الصفحة رقم 2

PACKING LIST MAIN UNIT Changer INSTALLATION PARTS Bracket (L) Bracket (R) Self-TappingScrew (M5 x 12) 1 pc. 1 pc. 4 pcs. HexagonalBolt 5 Meter DIN cable Seals with Washer (8 pin) M5x8 4 pcs. 1 pc. 1 pc. OTHER ACCESSORY CDMagazine Index seal sheet Installation Owner's Manual guide 1 pc. 1 pc. 1 pc. 1 pc. 1

ملخص المحتوى في الصفحة رقم 3

BEFOREINSTALLINGTHEUNIT Transport lock screws ThemechanismintheCDchangeris"locked"intoplaceduringshipmentbythe transportscrews. Besuretoremovethescrewspriortoinstallation. l Caution l Afterremovingthetransportlockscrews,placethesuppliedsealsoverthescrew holes. Thesesealsareusedtokeepdustoutoftheunit,whichcouldcauseamalfunction. InstallationandWiringPrecautions Topreventashort-circuit, 1 l Besuretoturnofftheignitionandremovethenegative(-)batterycable,priortoinstallation. l Connectpowerwireslast.

ملخص المحتوى في الصفحة رقم 4

SETTING THEANTI-VIBRATION SPRINGS This unit can be installed horizontally (suspended), vertically, and at a 45° angle. Once the installation position has been decided, it's necessarytosetthepositionofthebuilt-inanti-vibrationspringsinsidetheunit. Pleasedothisbeforeperformingtheprocedure. Vibration may cause the disc to skip if the unit is used before properly setting the anti-vibration springs. l At the time of shipping, the built-in anti-vibration springs is set for horizontal installation "H".

ملخص المحتوى في الصفحة رقم 5

PROCEDURE FORVERTICALINSTALLATION 1 l Confirmthatthebuilt-inanti-vibrationspringsonboththeleftandright sides are set to the vertical installation position "V". l Attachbracket(L)andbracket(R)usingthehexagonalbolts(M5x8). Determine the mounting location and drill four mounting holes. 2 Never mount the unit near the fuel tank. Drill holes 4mm in diameter. Secure the unit in place, using four self-tapping screws (M5 x 12). 3 Self-tapping screw (M5 x 12) PROCEDUREFOR45°ANGLE INSTALLATION 1 l Confirm

ملخص المحتوى في الصفحة رقم 6

PROCEDUREFORMOUNTINGUNDERREARDECK 1 l Confirmthatthebuilt-inanti-vibrationspringsonboththeleftandright sides are set to the horizontal installation position "H". l Attachbracket(L)andbracket(R)usingthehexagonalbolts(M5x8). 2 Determine the mounting location and drill four mounting Attach the CD changer using four self-tapping screws 3 holes. (M5 x 12). 4mm 5

ملخص المحتوى في الصفحة رقم 7

DIN cable (8-pin) VEHICLEWIRING Mating 8-pin DIN socket on rear of compatible radio chassis (see Note 1 below). Car Stereo with CD Changer Controls CD changer NOTE: 1. Check with your Audiovox car audio dealer to be sure your stereo is directly compatible with this CD changer. 2. Wiring instructions for use with FM Modulator/Commander Systems are included with the CDC-MC1, CDC-MCR2, P-MC3 and P-MCR4 accessories. 6