ملخص المحتوى في الصفحة رقم 1
T8001F, T8024F Flush Mount
Programmable Thermostat
INSTALLATION INSTRUCTIONS
3. Installer must be a trained, experienced service
APPLICATION
technician.
4. After installation is complete, check out product
The T8001F Thermostat provides single-stage,
operation as provided in these instructions.
programmable temperature control for 24 Vac heating-
cooling systems with manual changeover from heat to
cool. The T8024F Thermostat provides multistage
CAUTION
electronic control of single-zone heat
ملخص المحتوى في الصفحة رقم 2
T8001F, T8024F FLUSH MOUNT PROGRAMMABLE THERMOSTAT YES NO NO 5 FEET [1.5 METERS] NO M11338 Fig. 1. Typical location of thermostat. All wiring must comply with local electrical codes and ordinances. Disconnect the power supply to prevent electrical shock or equipment damage. WALL The shape of the terminals permits insertion of straight or wraparound wiring connections; either method is acceptable. A letter code is located near each terminal for identification. See Fig. 3 and 4. NOTE: To ensu
ملخص المحتوى في الصفحة رقم 3
T8001F, T8024F FLUSH MOUNT PROGRAMMABLE THERMOSTAT T8001 THERMOSTAT TERMINAL FOR STRAIGHT FOR WRAPAROUND SCREW INSERTION STRIP STRIP 7/16 IN. (11 MM) G 5/16 IN. (8 MM) C G R W 2 B C Y O 2 W2 HEAT R COOL RELAY DAMPER Y2 2 1 FAN COMPRESSOR HEAT W1 L1 CONTACTOR RELAY DAMPER (HOT) B L2 Y TRANSFORMER O 1 POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD PROTECTION AS REQUIRED. M20212 2 CAN BE USED FOR CHANGEOVER VALVE ON SINGLE-STAGE HEAT PUMP SYSTEMS. Fig. 4. T8024F wiring connections. M12566 Fig
ملخص المحتوى في الصفحة رقم 4
On Hold Select Fan PM TUE System Auto Cool Off Heat T8001F, T8024F FLUSH MOUNT PROGRAMMABLE THERMOSTAT 1. Enter Installer Setup. Setting Fan Operation (Fuel) Switch a. Use ▲ or ▼ keys to set the temperature set- (T8001F Only) point to 52°F (11°C). The fan operation (fuel) switch is preset at the factory in the F position. See Fig. 9. This is the correct setting for SET most systems. If this system is an electric heat system, set the switch to the E position. The E setting allows the HT. fan
ملخص المحتوى في الصفحة رقم 5
T8001F, T8024F FLUSH MOUNT PROGRAMMABLE THERMOSTAT 3. Setting Number of Cool/Heat Stages (T8024F Only). a. Press ▲ to display number of cool stages. M12588A c. Press the ▲ key to display control algorithm configuration default. M20216 b. Press ▼ to change number of cool stages. M14691 d. Press the ▲ key again to change control algo- rithm to C1 or C3. C1 = Standard control algorithm. M20215 C3 = Aggressive control algorithm (can c. Press ▲ to display number of heat stages. cause overshooting)
ملخص المحتوى في الصفحة رقم 6
On Hold Select Fan PM TUE System Auto Cool Off Heat T8001F, T8024F FLUSH MOUNT PROGRAMMABLE THERMOSTAT OPERATION Setting FAN and SYSTEM Switches Setting Current Time and Day Fan and system settings are controlled manually by 1. To Set Current Time. using the switches located at the bottom of the a. Press Select twice. thermostat case. See Fig. 11. SET FAN Switch PM Fan switch settings are: On: The fan runs continuously. Use for improved air M12591A circulation and air quality. Auto: Normal sett
ملخص المحتوى في الصفحة رقم 7
T8001F, T8024F FLUSH MOUNT PROGRAMMABLE THERMOSTAT CHECKOUT 1. Slide the SYSTEM switch to Cool and the FAN Heating switch to Auto. 1. Slide the SYSTEM switch to Heat and the FAN 2. Press the ▼ key to lower the temperature setting switch to Auto. several degrees below the room temperature; the 2. Press and hold the ▲ key to raise the temperature cooling equipment should start. The fan starts and setting several degrees above the room tempera- stops with the cooling equipment. ture; the heat
ملخص المحتوى في الصفحة رقم 8
T8001F, T8024F FLUSH MOUNT PROGRAMMABLE THERMOSTAT Home and Building Control Home and Building Control Honeywell Honeywell Limited-Honeywell Limitée 1985 Douglas Drive North 35 Dynamic Drive Golden Valley, MN 55422 Scarborough, Ontario M1V 4Z9 69-14653 G.H. Rev. 9-01 Printed in Mexico www.honeywell.com/yourhome
