ملخص المحتوى في الصفحة رقم 1
Installation & Operating Manual
The Harman FireLuxe Direct Vent Gas Stove
With Top Cooking Burner System
WARNING: If the information in these in-
This appliance may be installed in an after-
structions is not followed exactly, a fire or
market, permanently located manufactured
explosion may result causing property dam-
home (USA only) or in a mobile home, where
age, personal injury or loss of life.
not prohibited by local codes.
- Do not store or use gasoline or other flam-
This app
ملخص المحتوى في الصفحة رقم 2
AVERTISSEMENT: Assurez-vous de bien suivre les instructions données dans cette notice pour réduire au minimum le risque d’incindie ou d’explosion ou pour éviter tout dommage matériel, toute blessure ou la mort. - Ne pas entreposer ni utilizer d’essence ni d’autres vapeurs ou liquides inflammables dans le voisinage de cet appareil ou de tout autre appareil. - QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ: • Ne pas tenter d’allumer d’appareil. • Ne touchez à aucan interrupteur. Ne pa
ملخص المحتوى في الصفحة رقم 3
TABLE OF CONTENTS IMPORTANT SAFETY INFORMATION 4 SPECIFICATIONS 5 INSTALLATION 6 MASSACHUSETTS REQUIREMENTS 7 VENTING 8 ASSEMBLY 14 LIGHTING AND OPERATION 23 REMOTE CONTROL HANDSET OPERATION & PROGRAMMING 26 MAINTENANCE 28 PARTS LIST 30 WARRANTY 31 3
ملخص المحتوى في الصفحة رقم 4
IMPORTANT SAFETY INFORMATION The installation must conform with local codes or, in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1 or the Canadian Installation Code, CAN/CGA B149. A manufactured home (USA only) or mobile home OEM installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 or when such a standard is not applica- ble, the Standard for Manufactured Home Installations, ANSI/BCSBCS A225.1, or Standard
ملخص المحتوى في الصفحة رقم 5
SPECIFICATIONS MAIN BURNER Natural Gas Propane (LP) Input Rating-Btu/hr 36000 36000 Min. Input-Btu/hr 23000 23000 Orifice-DMS #34 #50 COOKING BURNER Input Rating-Btu/hr 12000 12000 Min. Input-Btu/hr 3500 3500 Orifice-DMS #52 #
ملخص المحتوى في الصفحة رقم 6
INSTALLATION Several issues must be addressed when selecting a suitable location for your FireLuxe. The minimum clearances to combustible construction are listed below. In addition, access to the gas supply and electrical supply must be considered. The location of the stove will also affect the venting requirements and you must be certain the location will allow compliance with the venting requirements shown on pages 8 – 13. You must also insure that your installation provides adequat
ملخص المحتوى في الصفحة رقم 7
INSTALLATION NOTE: If you will be installing the optional warming shelves, make sure to plan for the additional width that they occupy. For the details, see the information included with the warming shelf kit. The gas stove is shipped with a flexible connector that has a 1/2” NPT female connection. The gas supply piping should have a separate gas shutoff valve and a 1/8” NPT plugged tapping upstream of the valve. The stove and its main control valve must be disconnected from the gas su
ملخص المحتوى في الصفحة رقم 8
VENTING The FireLuxe Gas Stove has been tested and listed for installation with 4” X 6 5/8” Simpson DuraVent GS, AmeriVent Direct, Security Secure Vent and Selkirk DT direct venting components. For specific installa- tion requirements, follow the installation instructions included by the venting manufacturer with the venting system components you have chosen. The total vent length may not exceed 40 feet, including vertical rise and horizontal run. The vent lengths are measured from the
ملخص المحتوى في الصفحة رقم 9
VENTING Example 2 Fuel = Propane (LP) Vertical Rise = 6 feet 3 INLET AIR Horizontal Run = 8 feet Elbows = 3 Equiv. Horizontal Run = 16 feet (8+4+4) Air Restrictor Setting = C Exhaust Restrictor Setting = 3 C EXHAUST Example 3 Fuel = Natural Gas Vertical Rise = 22 feet Horizontal Run = 0 feet INLET AIR Elbows = 0 7 ⅜ Equiv. Horizontal Run = 0 feet Air Restrictor Setting = E ½ Exhaust Restrictor Setting = 7 ⅜ E½ EXHAUST Example 4 Fuel = Propane (LP
ملخص المحتوى في الصفحة رقم 10
VENTING NATURAL GAS VENTING VERTICAL RISE IN FEET 10 IF YOUR VENTING CONFIGURA- TION FALLS ABOVE THIS DOT- TED LINE, SEE PAGE 12 HORIZONTAL RUN IN FEET
ملخص المحتوى في الصفحة رقم 11
VENTING PROPANE (LP) GAS VENTING VERTICAL RISE IN FEET 11 IF YOUR VENTING CONFIGURA- TION FALLS ABOVE THIS DOT- TED LINE, SEE PAGE 12 HORIZONTAL RUN IN FEET
ملخص المحتوى في الصفحة رقم 12
VENTING PLEASE NOTE: If your specific venting configuration falls in a box in the venting charts (on pages 10 & 11) that is above the dotted line ( ), you must use one of the approved direct vent venting systems that utilizes a stainless steel inner liner. The dotted line corresponds to a total vent length of 30 feet includ- ing vertical rise and horizontal run. This requirement is part of the ANSI standards and is based on testing conducted to determine where the exhaust ga
ملخص المحتوى في الصفحة رقم 13
VENTING VENT TERMINAL CLEARANCES Venting terminals shall not be recessed into a wall or siding. 13
ملخص المحتوى في الصفحة رقم 14
ASSEMBLY UNPACKING AND PLACING THE FIRELUXE By now, you will have removed the shipping carton from the base pallet. The FireLuxe is shipped on spe- cially designed shipping supports that keep the weight of the stove off the legs to avoid damaging them dur- ing transit. Cut the strapping that secures the stove to the pallet. The stove must be lifted straight up to dis- engage it from the shipping brackets. The best place to lift is at the base of the stove sides. The stove top and front
ملخص المحتوى في الصفحة رقم 15
ASSEMBLY LOGS AND EMBERS Slide the logs and packing out of the firebox and set on the floor. Carefully unpack each of the four logs and three loose ember pieces. The logs and embers are somewhat fragile and will not survive being dropped from any significant height. Remove the protective cover material from the top of the burner. Each of the four logs is unique and must be placed in a precise location on top of the burner. The burner and log system is designed to facilitate correct p
ملخص المحتوى في الصفحة رقم 16
ASSEMBLY Place the left front log next. Again, there is a recess on the burner top that corresponds to the shape of the flat base of the log. Place the left end of the log in the recess and rest the right end on the left rear log using the illustration below as a guide. Place the right front log last. Again, place the flat base of the log in the corresponding recess in the burner top per the illustration below. LEFT FRONT LOG RIGHT FRONT LOG There are three loose ember pieces. Each
ملخص المحتوى في الصفحة رقم 17
ASSEMBLY When correctly placed, the logs and embers will look like the illustration below. After the logs and embers have been placed, the next step is to replace the glass panel and frame. Carefully pick up the glass and glass frame assembly by grasp- ing the sides of the frame and using your thumbs and fingers to hold the glass in place within the gasket and frame. With the glass frame (and glass) at a slight angle (leaving room for your fingers between the frame and the firebox) in
ملخص المحتوى في الصفحة رقم 18
ASSEMBLY Be sure that the inner and outer gaskets are in COVER their proper positions. Install and tighten the PLATE four screws. Finally, install the vent starter section in the rear vent position. Again, OUTER make sure that the inner and outer gaskets are GASKETS in their proper positions and install and INNER tighten the four screws. GASKETS At this time, you will also want to install the optional cast iron plate that fills in the top vent cutout on the stove top. With t
ملخص المحتوى في الصفحة رقم 19
ASSEMBLY Next, reinstall the top. This is a gravity fit. Carefully align the inner edge of the top with the outer edges of the sides and front. Lower the top down into place. Check to see if it is level and push down as needed to get the proper alignment relative to the aesthetic details on the front and sides. Finally, install the top cooking grate. This simply sits over the burner. A raised border on the stove top de- fines the cooking grate position. BATTERY INSTALLATION OR REPLA
ملخص المحتوى في الصفحة رقم 20
ASSEMBLY The main heating valve battery pack is located at the center rear of the stove. A removable valve access panel covers the valve components and simply lifts up and off the stove back. The batteries are located in the control module next to the actual valve. The battery access cover lifts and slides off to expose the four AA batteries. Note the orientation of each battery as you replace the old with new as this is critical to the operation of the control. Use only high quality
