ملخص المحتوى في الصفحة رقم 1
OUTDOOR STORAGE
OUTDOOR STORAGE BUILDING
OWNER’S MANUAL
MODEL 6424
30” OUTDOOR STORAGE EXTENSION KIT
Copy
ملخص المحتوى في الصفحة رقم 2
**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY** BEFORE BEGINNING ASSEMBLY Identify and inventory all parts using the checklist boxes on the Parts List. Keep the hardware bags and their contents separate. If any parts are missing, call our Customer Service Department. SAFETY INSTRUCTIONS Failure to follow these safety instructions may result in serious injury or property damage. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of
ملخص المحتوى في الصفحة رقم 3
HARDWARE IS ACTUAL SIZE (Unless otherwise indicated) AB AA AC AD TA TB 117 108 114 TE TJ TD TI 110 125 TF TK AE TH If you are Installing a New Shed 1. Check contents of boxes and compare to parts listed on the Parts List. 2. Follow instructions that came with your shed, but add extra floor panel, wall panels, Roof Cap and Skylight at appropriate points in the assembly. If you are Extending an Existing Shed 1. Remove any bolts or screws being used to anchor the shed to the ground. 2. Remove any o
ملخص المحتوى في الصفحة رقم 4
**Save all hardware for re-assembly!** 1 a. Remove last three skylights. 2 a. Remove the back 3 roof caps. 3 a. Remove the back Roof panels and Roof support bars. 4
ملخص المحتوى في الصفحة رقم 5
4 a. Remove the next Roof panels and Roof support bars. 5 a. Remove the Roof Truss. 5
ملخص المحتوى في الصفحة رقم 6
6 a. Remove the last two Side Wall Panels. Note: If you’re adding onto a side entry shed, remove the panels (in gray) from the side of the shed rather than removing the back of the shed. If you’re adding on to both sides, remove the panels (in gray) from both sides of the shed (as illustrated), and follow the remaining steps. 7 a. Slide the back section of the shed away from the front. You will need to tip the back section forward slightly in order to disconnect the floor panels Be sure th
ملخص المحتوى في الصفحة رقم 7
Assemble Window 8 TF (1) a. Remove plastic sheeting from Window (AE) and slide Window into slot TH (4) on the Window Wall Panel (125). Attach a Window Latch (TK) above each corner of the Window as shown. When tightening screws (TH), be sure that Window Latches will slide freely. Do not overtighten. Insert screw (TF) TK (2) into the hole in the window. Set panel aside. AE Insert window with bent edge at top and pointing away from the wall. Place Screw (TF) in this hole to keep window fro
ملخص المحتوى في الصفحة رقم 8
9 a. Add new Floor Panel (110). Then, slide the back section into place and connect the floor panels (you will need to tip the panels forward slightly to connect the panels). Tip up one floor panel and line up tabs and then lay floor panel flat. 10 a. Add Wall Panels (108). Insert a wood block directly under the tab you want to insert, then slide block to next tab and repeat. 8
ملخص المحتوى في الصفحة رقم 9
11 Assemble Truss TF (6) TE (6) a. Attach Brace (AC) to two Roof Truss Channels (AB) (one on each side of Brace. Secure Brace with Screws (TF) and Nuts (TE). Follow picture above to connect Brace to a Truss Channel at each end of the Brace. The nut goes on outside of the truss. b. Use Truss Connector (TA) to attach Roof Truss Channels at top. Secure with Screws (TF) and Nuts (TE). Before completely tightening, lay assembly on its side to be sure Channels and Brace are parallel. Complet
ملخص المحتوى في الصفحة رقم 10
c. Slide a Threaded Rod through the Truss Support Brace and the top of the Truss Connector. TD (2) TB TB d. Secure the top and bottom of the Threaded Rod with a 1/4” Cap Nut (TD). TD WARNING Do not overtighten the Cap Nut. TD 10
ملخص المحتوى في الصفحة رقم 11
12 a. Add Truss. 13 a. Add Roof Panels (114) and Roof Supports (AD). Roof Panel Ridge Roof Panel Wall b. Add a center Roof Cap (117). 11
ملخص المحتوى في الصفحة رقم 12
14 a. Add next Truss. 15 a. Add Roof Panels (114) and Roof Supports (AD). b. Add a center Roof Cap (117). 12
ملخص المحتوى في الصفحة رقم 13
16 a. Add Roof Panels (114) and Roof Supports (AD). b. Add the last Center Roof Cap (117) and the End Roof Cap. 17 a. Add Skylights 13
ملخص المحتوى في الصفحة رقم 14
® Enhance your Lifetime Outdoor Shed by purchasing the following Shed Accessories: Model # 0110 Corner Shelf (2 pack) Two 10” radius shelves with hardware. 0130 30” Shelf Kit w/ hardware (3 pack) Three 30” x 10” Steel-Reinforced Shelves with shelf brackets and hardware. 0150 90” Shelf Kit w/ hardware One 90” x 9” Steel-Reinforced Shelf with shelf bracket and hardware. 0113 16” Pegboard Strips w/ hardware Two sixteen inch Pegboard Strips with hooks. Great for hanging large items such as: r
