ملخص المحتوى في الصفحة رقم 1
®
INFINITY
Residential Elevator
Roped Hydraulic Residential Elevator
Planning Guide
ASME A17.1 - 2000 Part 5 Section 5.3
CAN/CSA B44 - 2000 Part 5 Section 5.3
Effective April 1, 2004
®
ELEVATORS and LIFTS
ملخص المحتوى في الصفحة رقم 2
INFINITY Residential Elevator Introduction This planning guide is designed to assist architects, contractors, home owners and elevator professionals in planning for an INFINITY Residential Elevator to meet the requirements of ASME A17.1 Part 5, Section 5.3 and CAN/CSA B44 Part 5, Section 5.3. We strongly recommend that you contact the code authority having jurisdiction in the area(s) where the elevator will be installed to become familiar with all the legal requirements governing the installa
ملخص المحتوى في الصفحة رقم 3
INFINITY Equipment for Residential Elevator Residential Elevator This elevator meets the requirements of ASME A17.1 Part 5, Section 5.3 and CAN/CSA B44 Part 5, Section 5.3 for a Residential Elevator General Safety Devices Rated Load: 750 lbs. (340kg) or 1000 lbs. (454kg) Easy access emergency manual lowering Nominal Speed: 36 fpm (.18 ms) Upper and lower terminal limits 2 Stop up to 10' travel (Up to 50' optional) Manual reset slack rope safety switch Data Plates, capacity tags and rope tags Au
ملخص المحتوى في الصفحة رقم 4
INFINITY Hoistway and Cab Configurations Residential Elevator Choice of Five Variations Important Note: Finished hoistway dimensions must include the drywall. Determine the fire rating of the hoistway, the type and layers of sheet rock and build only off shop drawings specific to your project. Available Cab Dimensions (Clear Inside): 35" x 48" 35" x 54" 35" x 60" Type 1 (S) - Enter/Exit Same Side Type 2 (W) - Enter/Exit Opposite Side LENGTH LENGTH Clear Cab Finished Clear Cab Finished Length
ملخص المحتوى في الصفحة رقم 5
INFINITY Hoistway and Cab Configurations Residential Elevator Type 5 (S) - Enter/Exit Same Side Diagram of Elevator Shaft (Opposite Sling) Overhead Elevator Guide LENGTH Rails Hydraulic Lifting Cylinder 3/8" Wire Rope Cable Elevator Cab Cab see chart Operating Panel Clear Cab Finished Side Entrance Length Hoistway Length Center Lines Cab Gate 48" 54 1/4" 27 1/8" 54" 60 1/4" 30 1/8" Pit 60" 66 1/4" 33 1/8" X X + 6 1/2" (X + 6 1/4") / 2 Hoistway Overhead Clearance Infinity Cab Height Ov
ملخص المحتوى في الصفحة رقم 6
INFINITY Specifications for Part 5.3 Compliance Residential Elevator PART 1 - GENERAL PART 2- PREPARATORY WORK BY OTHERS SCOPE 2.1 The following preparatory work to accommodate/receive the elevator is to To furnish all labor, materials and equipment necessary or required to be done by others. fully complete the installation of the elevator as indicated on the Drawings and Specifications. This suggested specification is intended to 2.1.1 cover the complete installation of the Concord INFINITY
ملخص المحتوى في الصفحة رقم 7
INFINITY Continued Specifications for Part 5.3 Compliance Residential Elevator PART 4 – PRODUCT DATA 4.2.10 AUTOMATIC LIGHTS Overhead lights in the car compartment shall turn ON automatically when 4.1 MANUFACTURER/PRODUCT the elevator door is opened and will stay on while the elevator is in use. The elevator shall be the CONCORD INFINITY Residential Elevator The elevator lights will shut off by a timer when the elevator is not in use. manufactured by Concord Elevator Inc. Toll Free (800) 661-
ملخص المحتوى في الصفحة رقم 8
INFINITY Continued Specifications for Part 5.3 Compliance Residential Elevator 4.15.3 4.10 CABLE Guides shall be bolted through the hoistway enclosure with back-up Minimum of two 3/8" (10 mm) IWRC Galvanized Aircraft Cables. Minimum breaking strength of 14,400 lbs. each. plates, washers and nuts. Subject to architects’ alterations and approval. 4.16 CAR SLING 4.11 SAFETY DEVICE A "slack/broken cable" safety device shall be supplied which will stop 4.16.1 and sustain the elevator and its rated
ملخص المحتوى في الصفحة رقم 9
INFINITY Wood Hoistway Construction Residential Elevator Suggested Support Wall Wood Construction Note: The drawings on this page are for reference only. Building structural engineer to ensure that the building and hoistway will support all loads imposed by the lift equipment. Fire rating of hoistway is subject to local building codes. CPG-INFVER01 © 2004, Concord Elevator Inc. Page 9 of 12
ملخص المحتوى في الصفحة رقم 10
INFINITY Wood Construction Sectional View Residential Elevator Wood Construction Plan View Rail Bracket CPG-INFVER01 © 2004, Concord Elevator Inc. Page 10 of 12
ملخص المحتوى في الصفحة رقم 11
INFINITY Masonry Construction Elevation View Residential Elevator BLOCK WALL (8" MINIMUM) Masonry Construction Plan View Rail Bracket Note: For 8" Block Use Thru Bolts CPG-INFVER01 © 2004, Concord Elevator Inc. Page 11 of 12 (See Note 1)
ملخص المحتوى في الصفحة رقم 12
INFINITY Elevator Rail Support Wall Residential Elevator Drawing Notes 1 See Elevator Drawing for rail bracket spacing and pit depth. 2 Wall lateral support spacing: - for 2" x 4" studs, use 6' -10" (2090 mm) max. - for 2" x 6" studs, use 13' -6" (4120 mm) max. 3 Sheathing installation: install sheets vertically full width of shaft or min. centred on rail brackets. 4 Connectors to resist horizontal load but allow vertical movement. For Wood, use 2" x ¼" cap screw lag bolts. General Specificat
