ملخص المحتوى في الصفحة رقم 1
ملخص المحتوى في الصفحة رقم 2
PUBLICATION ISSUED BY: Olivetti S.p.A. Gruppo Telecom Italia Via Jervis, 77 - 10015 Ivrea (ITALY) www.olivetti.com Copyright © 2006, Olivetti All rights reserved The mark affixed to the product certifies that the product satisfies the basic quality requirements. The manufacturer reserves the right to carry out modifications to the product described in this manual at any time and without any notice. ENERGY STAR is a U.S. registered mark. The ENERGY STAR program is an energy reduction pl
ملخص المحتوى في الصفحة رقم 3
CAUTIONS Caution label on the unit The label ( ) in the fusing area of the unit indicates the following: : Caution, risk of danger : Caution, hot surface Cautions on using the unit Follow the cautions below when using this unit. Warning: • The fusing area is hot. Exercise care in this area when removing misfed paper. Do not look directly at the light source. Doing so may damage your eyes. Do not switch the unit rapidly on and off. After turning the unit off, wait 10 to 15 seconds before tur
ملخص المحتوى في الصفحة رقم 4
Cautions on handling Be careful in handling the unit as follows to maintain the performance of this unit. Do not drop the unit, subject it to shock or strike it against any object. Do not expose the drum cartridge to direct sunlight. Doing so will damage the surface (green portion) of the drum cartridge, causing smudges on copies. Store spare supplies such as drum cartridges and TD cartridges in a dark place without removing from the package before use. If they are exposed to direct sunli
ملخص المحتوى في الصفحة رقم 5
CONTENTS 1 INTRODUCTION 5 MAKING COPIES USING THE MANUALS................. 4 COPY FLOW ...............................46 1 PART NAMES................................ 5 ORIGINAL PLACEMENT.............47 OPERATION PANEL ..................... 6 SET THE COPY QUANTITY .......49 EXPOSURE ADJUSTMENT/ 2 SETTING UP THE UNIT PHOTO COPYING.......................50 REDUCTION/ENLARGEMENT/ SETUP PROCEDURE................... 7 2 ZOOM ..........................................52 CHECKING PACKED COMPONENTS AND
ملخص المحتوى في الصفحة رقم 6
INTRODUCTION 1 This chapter provides basic information for using the unit. USING THE MANUALS In addition to this printed manual an online manual is also provided. To get full use of all features and functions of this product, be sure to familiarize yourself with both manuals. This printed manual provides all installation and setup instructions as well as instructions in the use of all copier functions. The online manual contains the following information. Online manual Provides you with infor
ملخص المحتوى في الصفحة رقم 7
PART NAMES 1 Power switch 10 Original table 1 Handle 11 Operation panel 2 Power cord socket 12 Front cover 3 Fusing unit release lever 13 Paper tray 4 Transfer charger 14 Side cover 5 Charger cleaner 15 Side cover open button 6 Bypass paper guides 7 Paper output tray 8 Paper output tray extension 9 5
ملخص المحتوى في الصفحة رقم 8
OPERATION PANEL 11 ON LINE key and indicator Original to copy key and indicators 1 Lights up when the unit is used as a Two-sided copies from printer and scanner. For description of one-sided originals. the ON LINE indicator, see Turn on Long Edge or "INDICATORS ON THE OPERATION Turn on Short Edge PANEL" (p.31). can be selected. 12 Power save indicator Exposure mode selector key and 2 Lights up when the unit is in a power indicators save mode. (p.55, p.56) Use to sequentially select the
ملخص المحتوى في الصفحة رقم 9
SETTING UP THE UNIT 2 Follow the installation procedure below to use the unit properly. If the unit does not function properly during setup or use, or if a function cannot be used, see "TROUBLESHOOTING THE UNIT" (p.62). 2 SETUP PROCEDURE When using the unit for the first time, setup the unit following the procedure shown below. 1 Open the package, and make sure that all the accessories are supplied with the unit. (p.8) 2 Remove the protective materials. (p.9) 3 Install the TD cartridge. (p.10
ملخص المحتوى في الصفحة رقم 10
CHECKING PACKED COMPONENTS AND ACCESSORIES Open the carton and check if the following components and accessories are included. If anything is not included or is damaged, contact your authorized Service representative. PREPARING THE UNIT FOR INSTALLATION Be sure to hold the handles on 1 both sides of the unit to unpack the unit and carry it to the installation location. 8 Power cord
ملخص المحتوى في الصفحة رقم 11
Remove all pieces of tape shown in the illustration below. Then 2 open the original cover/SPF and remove protective materials. After that, take out the bag containing the power cord and TD cartridge. 2 12 cpm model 15 cpm model 12 cpm model 15 cpm model SCAN HEAD LOCKING SWITCH The scan head locking switch is under the original table. If the switch is locked ( ), the unit will not operate. Unlock the switch () as shown below. 9
ملخص المحتوى في الصفحة رقم 12
INSTALLING THE TD CARTRIDGE Open the side cover. 1 Push gently on both sides of the 2 front cover to open the cover. Remove the TD cartridge from the bag. Hold the cartridge on 3 both sides and shake it horizontally four or five times. Hold the tab of the protective cover and pull the tab to your side to remove the cover. 4 or 5 times Gently insert the TD cartridge 4 until it locks in place while pushing the lock release button. 10
ملخص المحتوى في الصفحة رقم 13
Close the front cover and then 5 the side cover by pressing the round projections near the side cover open button. When closing the covers, be sure to close the front cover securely and then close the side cover. If the covers are closed in the wrong order, the 2 covers may be damaged. 11
ملخص المحتوى في الصفحة رقم 14
CONNECTING THE POWER CORD If you use the unit in a country other than the country where the unit was purchased, you will need to make sure that your local power supply is compatible with your model. If you plug the unit into an incompatible power supply, irreparable damage to the unit will result. Ensure that the power switch of 1 the unit is in the OFF position. Insert the attached power cord into the power cord socket at the rear of the unit. Plug the other end of the power cord into th
ملخص المحتوى في الصفحة رقم 15
About the scan head The scan head lamp remains on constantly when the unit is in the ready condition (when the Start indicator is illuminated). The unit adjusts the scan head lamp periodically to maintain copying quality. At this time, the scan head moves automatically. This is normal and does not indicate unit trouble. Initial settings of operation panel When the unit power is on, the operation panel will revert to the initial settings when the time set with the "Auto clear time" setting (p
ملخص المحتوى في الصفحة رقم 16
LOADING PAPER 3 Follow the steps below to load paper into the tray. PAPER For best results, use only paper recommended by OLIVETTI. Type of paper Type of media Size Weight feeding 2 Paper tray Standard paper A4 56 to 80g/m B5 A5 Letter Legal Invoice 2 Single bypass Standard paper and A4 52 to 128g/m ** thick paper B5 A5 B6 A6 Letter Legal Invoice Special Transparency A4 media film Letter Envelope* International DL International C5 Commercial 10 Monarch * Do not use non-standard envelopes, and en
ملخص المحتوى في الصفحة رقم 17
LOADING THE PAPER TRAY Raise the handle of the paper tray 1 and pull the paper tray out until it stops. Remove the pressure plate lock. Rotate the pressure plate lock 2 in the direction of the arrow to remove it while pressing down the pressure plate of the paper tray. 3 Store the pressure plate lock which has been removed in step 2. 3 To store the pressure plate lock, rotate the lock to fix it on the relevant location. Pressure plate lock Adjust the paper guides on the paper tray to the c
ملخص المحتوى في الصفحة رقم 18
Fan the paper and insert it into the tray. Make sure the edges go 5 under the corner hooks. Do not load paper above the maximum height line ( ). Exceeding the line will cause a paper misfeed. Gently push the paper tray back into the unit. 6 After loading paper, to cancel the blinking without restarting copying, press the clear ( ) key. The in the display will go out and the start ( ) indicator will light up. Be sure that paper is free of rips, dust, wrinkles, and curled or bent edges.
ملخص المحتوى في الصفحة رقم 19
BYPASS FEED (including special paper) The single bypass can be used to feed standard paper, transparency film, labels, envelopes, and other special purpose paper. Paper measuring from A6 to A4/Legal and in the weight range 2 2 of 52 to 128g/m can be used in this tray. (For paper weighing from 104 to 128g/m , A4 is the maximum size.) The single bypass can hold one sheet of paper. The original image must be smaller than the paper or media for copying. If the original image is bigger than
ملخص المحتوى في الصفحة رقم 20
Note for loading envelopes Envelopes must be fed narrow side into the feed slot one sheet at a time. Do not use non-standard envelopes, and envelopes that have metal clasps, plastic snappers, string closures, windows, linings, self-adhesive, patches or synthetic materials. Do not use envelopes that are filled with air or envelopes that have labels or stamps attached. Envelopes of which the surface is not flat because of embossing may cause the prints to become smudged. Under high hum
