ملخص المحتوى في الصفحة رقم 1
OUTDOOR TEMPERATURE TRANSMITTER:
WS-8157
ATOMIC CLOCK WITH OUTDOOR WIRELESS TEMPERATURE
AND WEATHER FORECAST
Instruction Manual
Holder
FEATURES:
ATOMIC CLOCK:
Hanging holes
• Remote transmission of outdoor temperature to the atomic clock by 433 MHz signals
LCD1 • Wall mounting case
display
Function keys
TO INSTALL AND REPLACE BATTERIES IN THE ATOMIC CLOCK
LCD2
The atomic clock uses 2 x AA, 1.5V batteries
ملخص المحتوى في الصفحة رقم 2
To display the alarm time in normal mode display Alkaline batteries are recommended for use in both units. Avoid using rechargable To exit the setting modes batteries. NOTE: Do not set the clock until the outdoor temperature is displayed. ATOMIC CLOCK LCD SCREEN DESCRIPTIONS 1. Place batteries in the outdoor transmitter first, then into the atomic clock. DO NOT The atomic clock's LCD is divided into 2 sections and once the batteries are inserted, all the PRESS ANY BUTTONS FOR 10 M
ملخص المحتوى في الصفحة رقم 3
MANUAL SETTINGS Note: Weather Icons If the atomic clock has already successfully received the WWVB time signal and displays the correct time and date, then the Manual settings can be skipped. There are 3 possible weather icons that will be displayed in the LCD 2: After completion of the above described procedures in “Setting up” the manual setting modes can be entered by pressing and holding the SET key for 3 seconds. The following settings can now be Sunny—indicates that th
ملخص المحتوى في الصفحة رقم 4
attempts the WWVB tower icon will flash. If reception has been unsuccessful, then the WWVB tower • -8 PST (Pacific time), icon will not appear but reception will still be attempted the following hour. • -9 ALA (Alaska time), • -10 HAW (Hawaii time). WWVB time reception takes place from 12:00 am through 6:00 am each day (attempts WWVB • "GMT” will be displayed if set to GMT (0). reception every full hour within this time frame). When the time signal is received for example at 1:00 2.
ملخص المحتوى في الصفحة رقم 5
OUTDOOR TEMPERATURE TRANSMITTER: °C OR °F TEMPERATURE SETTING The temperature is measured and transmitted to the atomic clock every 1 minute. The atomic clock 1. The characters “°C” or “°F” will start flashing on LCD1 (Default setting °F). By use of the + key will update the temperature display every 5 minutes. select “°C” for temperature display in degrees Celsius or “°F” for degrees Fahrenheit. The range of the outdoor temperature transmitter may be affected by the temperature. At co
ملخص المحتوى في الصفحة رقم 6
1. Press the + key. The display should now show the month&date/weekday/seconds/outdoor In case the atomic clock is not able to detect the WWVB-signal (disturbances, transmitting distance, temperature. etc.), the time can be manually set (please refer to notes on Manual time setting) . 2. Press the + key a second time and the display will now show the month&date/weekday/indoor temperature/seconds. 3. Press the + key third time and the display will now show the month&date/seconds/indoor
ملخص المحتوى في الصفحة رقم 7
WALL MOUNTING 3) Remove the protective strip from the other side of the tape. Position the outdoor temperature 1) Using a straightedge, horizontally space at 2-3/4 of an inch (70 mm) three transmitter in the desired location, ensuring that the atomic clock can receive the signal. screw positions on a wall. TROUBLESHOOTING: 2) Install three mounting screws (not included) into a wall within transmission Problem: The LCD is faint. range—leaving approximately 3/16 of an inch (5mm) extended
ملخص المحتوى في الصفحة رقم 8
CARE AND MAINTENANCE: LIABILITY DISCLAIMER: • Avoid placing the units in areas prone to vibration and shock as these may cause damage. • The manufacturer and supplier cannot accept any responsibility for any incorrect readings and • Avoid areas where the units can be exposed to sudden changes in temperature, i.e. direct any consequences that occur should an inaccurate reading take place. sunlight, extreme cold and wet/moist conditions as these will lead to rapid changes which reduces • Thi
ملخص المحتوى في الصفحة رقم 9
WARRANTY INFORMATION La Crosse Technology provides a 1-year warranty on this atomic clock. Contact La Crosse Technology immediately upon discovery of any defects covered by this warranty. Before sending the atomic clock in for repairs, contact La Crosse Technology. The atomic clock will be repaired or replaced with the same or similar model. This warranty does not cover any defects resulting from improper use, unauthorized repairs, faulty batteries, or the clocks inabili
