ملخص المحتوى في الصفحة رقم 1
Owner's Manual
I CRAFTSHAN I
46"- 2 STAGE SNOW THROWER
TRACTO R ATTAC HM ENT
Model No. 486.248462
• Safety
CAUTION:
• Assembly
Before using this product, read
• Operation
this manual and follow all
• Maintenance
Safety Rules and
• Parts
Operating Instructions.
IMPORTANT - READ THIS FIRST!!!
For Missing Parts or Assembly Questions
Please Call 217-726-6366
Mon.-Fri. 7 am - 5 pm CST.
FAX 217-726-2032 or e-mail info@agri-fab.com
Missing parts will be sent UPS in 24 hours directly to your home.
Sears
ملخص المحتوى في الصفحة رقم 2
ACCESSORIES ......................................................... 2 SERVICE AND ADJUSTMENTS ............................ 16 SAFETY RULES ........................................................ 3 STO RAG E ................................................................ 17 FULL SIZE HARDWARE CHART ............................. 4 TROUBLESHOOTING ............................................. 17 CARTON CONTENTS ............................................... 5 REPAIR PARTS ILLUSTRATION ........
ملخص المحتوى في الصفحة رقم 3
Any power equipment can cause injury if operated improperly or if the user does not understand how to operate the equipment. Exercise caution at all times, when using power equipment. • Read this owner's manual carefully and know how • Stop the engine whenever you leave the operating to operate your snow thrower and how to stop the position, before unclogging the snow thrower or unit and disengage the controls quickly. making any adjustments or inspections. • Never allow children to operate the
ملخص المحتوى في الصفحة رقم 4
SHOWN ACTUAL SIZE H \ \ _J NOT SHOWN ACTUAL SIZE Two shear bolts (R) and hex lock nuts (S) are provided as _ jT replacement parts for the spiral augers. Store in a safe place until needed. (See page 16.) REF. QTY. DESCRIPTION REF. QTY. DESCRIPTION A M 2 Bowed Washer 2 Hex Bolt, 3/8" x 1-1/2" B N 6 Washer, 1/4" 12 Hex Bolt, 3/8" x 1" C O 2 Washer, 5/16" 2 Hex Bolt, 5/16" x 1-3/4" D P 2 Washer, 3/4" 6 Hex Bolt, 1/4" x 1" E 2 Carriage Bolt, 5/16" x 1-3/4" Q 4 Hairpin Clip, 1/8" F R 2 Shear Bolt 6 C
ملخص المحتوى في الصفحة رقم 5
CARTON CONTENTS 1. Frame Bracket, R.H. 2. Frame Bracket, L.H. 10. Side Brace Arms (2) 3. Hanger Bracket, L.H. 11. Chute Crank Assembly 4. Hanger Bracket, R.H. 12. Lift Handle with Cable 5. Side Plate, L.H. 13. Clutch/Idler Assembly 6. Side Plate, R.H. 14. Drive "V" Belt 7. Cross Brace 15. Auger "V" Bett (Attached to Housing Assembly) 8. Plastic Weight Keg 16. Anti-rotation Bracket 9. Weight Tray 17. Chute and Control Cable Assembly 18. Housing Assembly Hardware Package (Stored inside Plastic Keg
ملخص المحتوى في الصفحة رقم 6
TOOLS REQUIRED FOR ASSEMBLY ASSEMBLING PARTS TO TRACTOR FRAME 7/16" Wrenches (2) Right hand (R.H.) and left hand (L.H.) are determined 1/2" Wrenches (2) from the operators position while seated on the tractor. 9/16" Wrenches (2) (t) 5/8" Wrench or Adjustable Wrench • Remove the hex bolt from the threaded hole at the (t) 11/16" Wrench or Adjustable Wrench top front corner of R.H. front suspension bracket. (t) 3/4" Wrench or Adjustable Wrench Remove the nut from the carriage bolt at the top Knife
ملخص المحتوى في الصفحة رقم 7
Assemble the L.H. hanger bracket to the left side of • Remove the mower stop bracket and its two bolts and nuts from the R.H. side of the tractor frame as the tractor frame using two 3/8" x 1" hex bolts, two 3/8" lock washers and two 3/8" hex lock nuts as shown in figure 3. shown in figure 5. • If the tractor has a muffler guard at the front of the R.H. foot rest, remove the bottom bolt and nut, and the washer which is located between the guard and \ \ the tractor frame. See figure 3. LH. HANGER
ملخص المحتوى في الصفحة رقم 8
ASSEMBLY OF SNOW THROWER ATTACHING CLUTCH/IDLER ASSEMBLY Place the lift handle into the lift bracket on the right side of the snow thrower. Fasten the handle to the IF YOUR MOWER DECK SIZE IS OTHER THAN 48" bracket using two 5/16" x 1-3/4" hex bolts, 5/16" • Before attaching the clutch idler assembly to the lock washers and 5/16" hex nuts. See figure 9. tractor, measure the outer diameter of the tractor's engine pulley. If the diameter of the pulley is less than 6", move the 3/32" hairpin clip i
ملخص المحتوى في الصفحة رقم 9
Remove the nylon tie which fastens the chute crank rod to the crank support tube. Assemble the crank support tube (flat side) to the two brackets on the left side of the thrower housing using two 3/8" x 1-1/2" hex bolts, 3/8" lock washers and 3/8" hex lock nuts. See figure 11. / CHUTE CRANK ASSEMBLY 3/8" x 1-1/2" 5/16"LOCK HEX BOLT WASHER 5/16" HEX NUT FIGURE 13 LEFT SIDE VIEW Coat the top of the ring around the discharge CRANK " 3/8" LOCK opening with general purpose grease. See figure 14. SUPP
ملخص المحتوى في الصفحة رقم 10
MOUNTING SNOW THROWER TO TRACTOR ASSEMBLING THE BELTS NOTE: The help of another person may be required to IMPORTANT: The tapered "V" section of the belts must mount the snow thrower to the front of the tractor. be seated into the grooves of the V-pulleys. • Place the tractor and snow thrower on a flat, level DRIVE BELT surface. • Remove the two outside 1/8" hairpin clips which • Remove the plastic tie from the auger belt and are assembled to the L.H. and R.H. tension adjust- extend the belt out
ملخص المحتوى في الصفحة رقم 11
AUGER BELT • Raise the snow thrower to the transport position. • Make sure the auger belt is correctly assembled to • Place the auger belt around the bottom rear pulley the snow thrower. The belt must pass over the top on the clutch/idler assembly and between the two of the auger pulley and then twist 1/4 turn to pass pulleys on the lower idler arm. Keep the flat idler underneath the two side idler pulleys on the snow pulley to the outside of the belt. See figure 18. thrower. The "V" side of the
ملخص المحتوى في الصفحة رقم 12
ATTACHING WEIGHT TRAY TO TRACTOR • Place the weight keg on the weight tray and fill with approximately 100 lbs. of dry sand. • Secure the keg with the rubber tarp strap hooked • Loosen the two hex bolts and nuts which fasten the into the holes in the cross brace. See figure 20. top of the tractor drawbar to the rear of the tractor frame. See figure 19. • Assemble the notched end of the side brace arms down onto both loosened bolts. Do not tighten yet. See figure 19. • Fasten the weight tray to t
ملخص المحتوى في الصفحة رقم 13
KNOW YOUR SNOW THROWER Read this owner's manual and safety rules before operating your snow thrower. Compare the illustration below with your snow thrower to familiarize yourself with the various controls and their locations. ;ER CHUTE T,LT .ANDLE LIFT HANDLE CRANK ROD UPPER CHUTE LOWER CHUTE LEVELING SHOE (Behind housing) SCRAPER PLATE SKID SHOE / SPIRAL AUGERS, R.H.& L.H. UPPER AND LOWER DISCHARGE CHUTE Controls CHUTE TILT HANDLE Pivots the Upper Chute up or down to control the angle and dista
ملخص المحتوى في الصفحة رقم 14
HOW TO USE YOUR SNOW THROWER • In extremely deep snow, raise the snow thrower from the ground to remove the top layer and drive forward only until the tractors front tires reach the CAUTION: Never direct discharge uncleared bottom layer of snow. Depress the towards bystanders or windows. Do not & tractor's clutch-brake pedal and allow the spiral allow anyone in front of unit. auger to clear the snow. Reverse the tractor and lower the snow thrower to the ground. Drive the CONTROLLING SNOW DISCHAR
ملخص المحتوى في الصفحة رقم 15
CUSTOMER RESPONSIBILITIES • Read and follow the maintenance schedule and the maintenance procedures listed in this section. MAINTENANCE SCHEDULE Fill in dates as you Service Dates complete regular service. Check for loose fasteners x Check belts for wear x x x Check scraper and shoes for wear x x Cleaninq Lubrication Section x CHECK FOR LOOSE FASTENERS LUBRICATION • Before each use make a thorough visual check of • Oil all pivot points on snow thrower lift mechanism. the snow thrower for any bol
ملخص المحتوى في الصفحة رقم 16
CAUTION: Before servicing or adjusting SKID SHOE, LEVELING SHOE ADJUSTMENT the snow thrower, shut off the engine, (The snow thrower must be attached to the tractor for remove the spark plug wire(s), set the correct adjustment of the shoes.) & parking brake and remove the key from the tractor ignition. • The skid shoes regulate the distance the scraper plate is raised above the plowing surface. They are REPLACING AUGER BELT mounted on each side of the spiral auger housing. • Raise the snow throwe
ملخص المحتوى في الصفحة رقم 17
STORAGE RECOMMENDATIONS PARTS TO REMOVE AT END OF SEASON • Remove the "V" belt from the engine pulley and the • Lower the snow thrower to the ground and remove it from the tractor. clutch/idler assembly. See figure 16 on page 10. • Remove the clutch/idler assembly. (The two hanger • Clean the snow thrower thoroughly. Wash off any brackets and the two frame brackets should not salt deposits which may have dried on the thrower create any interference with the mower deck and and housing. may be lef
ملخص المحتوى في الصفحة رقم 18
REPAIR PARTS FOR MODEL 486.248462 46" SNOW THROWER 106 105 13 52 40 51 61 106 58 57 I 60 30 59_ 107 22 13 62 "7 13 .11 95 33 104 94 103 46 13- 10 47 _ 19 23_ 14 20 14 38 108 34 ! 15 29 61 13 2 21 42 31 39 14 71 39 18 86 35 .. 38 65 112 .110 37 8_7__._ _. 109 38 39 38 / / _J_ 38 88 _87 111 100 80 68 18
ملخص المحتوى في الصفحة رقم 19
REPAIR PARTS FOR MODEL 486.248462 46" SNOW THROWER REF. PART QTY. DESCRIPTION REF. PART QTY. DESCRIPTION NO. NO. NO. NO. 1 63576 1 Housing Assembly 58 684-0061 1 Chute Crank Assembly 2 64517 U-Joint 1 Impeller Assembly 59 784-5149 1 3 47368 Roll Pin, 1/8" x 5/8" 2 Spring Pin, 5/16" x 1-3/4" 60 43850 2 4 47369 Flat Washer, 3/8" 2 Spring Pin, 3/16" x 1-3/4" 61 43070 8 5 63772 Chute Crank Bracket, Rear 1 Spiral Assembly, R.H. 62 24300 1 6 63771 Chute Crank Bracket, Front 1 Spiral Assembly, L.H. (No
ملخص المحتوى في الصفحة رقم 20
REPAIR PARTS FOR MODEL 486.248462 46" SNOW THROWER \ 53 33 34 64 52 51 31 37 35 \ 36 54 19 13 ! 20 19 18 14 19 14 15 19 13 17 28 19 20 22 _28 54 26 2 ,.....,20 39 45 \ 24 44 12 \8 29 / I 51 A 52 58 30 59 51 52 49 47 26 54 2O
