ملخص المحتوى في الصفحة رقم 1
GASOLINE AUGER DRILL
1.5 HP
Model 95346
ASSEmbLy AND OPERAtION INStRUctIONS
Due to continuing improvements, actual product may differ slightly from the product described herein.
CAUTION!
Your Warranty Is Voided If:
You do not operate the Auger Drill with the proper 25:1 unleaded fuel/2-cycle oil mix in its fuel tank. Never run
the Engine with an improper fuel mix, low or no fuel mix. Running the Engine with an improper fuel mix, low
or no fuel mix, will permanently damage the unit.
You do no
ملخص المحتوى في الصفحة رقم 2
SPECIFICATIONS Engine Specifications 1.5 HP / 52cc / Single Cylinder / 2-Stroke / Recoil Start Fuel Required 25:1 Unleaded Gasoline (89 octane or better) & 2 Cycle Oil Mixture Fuel Tank Capacity 0.26 Gallon Recommended Gear Oil SAE 80 – 90 Weight Gear Oil Rotation Single Rotation Only (Clockwise) Drilling Speed 150 RPM Maximum Drilling Depth 1’ 10” Auger Diameter 4” Overall Bit Length 2’ 6-3/4” Long Cutting Edge Length 2’ Long Drive Shaft 7/8” Diameter x 1-1/2” Long Accessories Auger Bit / Fuel
ملخص المحتوى في الصفحة رقم 3
GENERAL SAFETY RULES AND PRECAUTIONS wARNING! READ AND UNDERSt AND ALL INStRUctIONS f ailure to follow all instructions listed below may result in electric shock, fire, and/or serious injury. SAVE tHESE INStRUctIONS WORK AREA 1. Keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. 2. Do not operate power tools in explosive atmospheres, such as in the pres- ence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or
ملخص المحتوى في الصفحة رقم 4
2. Do not use the Auger Drill if the Kill Switch does not turn it off. Any tool that cannot be controlled with its Kill Switch is dangerous and must be replaced. 3. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. 4. Maintain tools with care. Properly maintained tools are less likely to malfunction and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. 5. Check for mi
ملخص المحتوى في الصفحة رقم 5
4. Never leave the Auger Drill unattended when it is running. Turn off the Engine before leaving. 5. Do not allow children and other unauthorized people to handle or play with the Auger Drill. Never leave the drill unattended in an area accessible to children. 6. Always maintain a firm grip on the Auger Drill with both hands and be aware of the strong start-up torque of the tool. 7. Always keep your thumb near the Kill Switch in the event the Auger Drill must be turned off immediately. 8.
ملخص المحتوى في الصفحة رقم 6
3. When spills of fuel or oil occur, they must be cleaned up immediately. Dis- pose of fluids and cleaning materials as per any local, state, or federal codes and regulations. Store oil rags in a covered metal container. 4. Never store fuel or other flammable materials near the Auger Drill. 5. Do not smoke, or allow sparks, flames, or other sources of ignition around the Auger Drill. 6. Keep grounded conductive objects, such as tools, away from exposed, live electrical parts and connections
ملخص المحتوى في الصفحة رقم 7
ADDITIONAL PRECAUTIONS 1. DANGER! People with pacemakers should not use this tool. This tool produces strong electromagnetic fields that can cause pacemaker interference or pacemaker failure. People with pacemakers should consult their physician(s) for advice. 2. WARNING! The warnings and precautions discussed in this manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be
ملخص المحتوى في الصفحة رقم 8
PRE-START INSTRUCTIONS Fill the Fuel Tank 1. IMPORTANT! Your warranty is voided if you do not operate the Auger Drill with the proper 25:1 fuel mix in its Fuel Tank (89). Never run the Engine with an improper fuel mix, low or no fuel mix. Running the Engine with an improper fuel mix, low or no fuel mix will permanently damage the unit. 2. To obtain the proper 5:1 fuel mix, combine 5 parts unleaded gasoline (89+ octane) with 1 part -cycle oil in the provided Fuel Mix Container (36a).
ملخص المحتوى في الصفحة رقم 9
OPERATION Starting and Stopping 1. WARNING! Always wear safety equipment. When operating the Auger Drill, always wear ANSI-approved safety impact eye goggles, hearing protection, heavy duty work gloves, sturdy work boots, and head protection. 2. Place the Auger Drill on its side with its Auger (33a) resting upon the ground surface location that is to be drilled. Make sure that no debris, clothing, or other objects are near the auger bit. Keep all bystanders away. CHOKE (76) PRIMER (95) F
ملخص المحتوى في الصفحة رقم 10
6. WARNING! The Auger (33a) should never turn at idle. If it is turning at idle, turn the Idle Stop Idle Screw of the Carburetor Screw (shown right) counterclock- Location wise to reduce the idle RPM and stop the Auger, or imme- diately discontinue using the Auger Drill and contact a quali- fied service technician to make the adjustment. 7. Once the Engine is started, set the Choke (6) to its open position. 8. If the Engine does not start, press the Primer (95) again. Set the Cho
ملخص المحتوى في الصفحة رقم 11
ملخص المحتوى في الصفحة رقم 12
INSPECTION, MAINTENANCE, AND CLEANING 1. WARNING! Always make sure the Spark Plug (51) is removed and the engine has cooled completely prior to performing any service, maintenance, or cleaning of the Auger Drill. 2. Before each use: Inspect the general condition of the Auger Drill. Check mis- alignment or binding of moving parts, cracked or broken parts, dull or damaged Auger (33a), and any other condition that may affect the safe operation of the tool. If abnormal noise or vibration occ
ملخص المحتوى في الصفحة رقم 13
TROUBLESHOOTING Problem Possible Cause Possible Solution Engine will not start. 1. Low or no fuel in fuel tank or 1. Fill fuel tank with proper 5:1 unleaded improper fuel/-cycle oil mix. gasoline/-cycle oil mix. 2. Not enough fuel getting to 2. Press primer 3-4 times. Set choke to carburetor. “START”. Then attempt to start engine. 3. Faulty spark plug. 3. Clean or replace spark plug. 4. Contaminated fuel. 4. Have a qualified service technician empty old fuel from fuel tank. Then, refill
ملخص المحتوى في الصفحة رقم 14
PARTS LIST - ENGINE Part Description Qty. Part Description Qty. 1 Set Screw (M5 x 1) 1 49 Bolt (M5 x 18) 4 Gasket 1 50 Cylinder Cover 1 3 Reel 1 51 Spark Plug 1 4 Starter Rope 1 5 Spark Plug Clip Reed 1 5 Spiral Spring 1 53 Spark Plug Cover 1 6 Rewind Starter Assy. 1 54 Spark Plug Cap 1 Starter Handle 1 55 Cap Cover 1 8 Handle Clip 1 56 Top Cover 1 9 Screw (M5 x 0) 6 5 Screw (M5 x 0) 1 10 Crankcase Gasket 1 58 Muffler Insulator 1 11 Nut (M8) 1 59 Muffler 1 1 Startup Claw 1 60 Socket He
ملخص المحتوى في الصفحة رقم 15
ASSEMBLY DIAGRAM - ENGINE SKU 95346 For technical questions, please call 1-800-444-3353 PAGE 15
ملخص المحتوى في الصفحة رقم 16
PARTS LIST - GEARBOX UNIT Part Description Qty. Part Description Qty. 1a Starting Flange 1 1a Bolt (M6 x 1) 1 a Oil Seal (0 x 5 x ) 1 a Washer 1 3a Washer 1 3a Paper Underlay 1 4a Washer 1 4a Screw (M6 x 16) 6 5a Fender Ring (4) 1 5a Cushion Frame 1 6a Bearing (604) 1 6a Liner Tube 5 a Worm Gear 1 a Washer 10 8a Gearbox 1 8a Washer (6) 1 9a Hex Head Screw (M6 x 5) 4 9a Hex Head Screw (M6 x 30) 5 10a Stud (M6) 4 30a Screw 4 11a Nut (M6) 4 31a Nut 4 1a Washer 1 3a Was
ملخص المحتوى في الصفحة رقم 17
PARTS LIST & ASSEMBLY DIAGRAM - FRAME Part Description Qty. Part Description Qty. 1b Frame (Complete) 1 6b Kill Switch Bracket 1 b Handle 1 b Screw (M1 x 0) 3b Tie Strip 3 8b Accelerator Cable 1 4b Handle 1 9b Bushing 1 5b Kill Switch 1 10b Speed Control 1 SKU 95346 For technical questions, please call 1-800-444-3353 PAGE 1
ملخص المحتوى في الصفحة رقم 18
Emission Control System Warranty United States Emission Control Defects Warranty Statement ® The United States Environmental Protection Agency (herein EPA), and Harbor Freight Tools (herein HFT) are pleased to explain the emission control system warranty on your 1995 and later Small Off-Road Engine (herein engine). Within the United States, new off-road, spark-ignition engines certified for model year 1997 and later, must meet similar standards set forth by the EPA. HFT must warrant the emi
ملخص المحتوى في الصفحة رقم 19
Emission Control System Warranty - continued Harbor Freight Tools Emission Control Defects Warranty Provisions 5. Service and Maintenance Component parts which are not scheduled for replacement as required maintenance or are scheduled only for regular inspection to the effect of “repair or replace as necessary” are warranted for the warranty period. Any warranted part which is scheduled for replacement as required maintenance is warranted for the period of time up to the first scheduled replac
