ملخص المحتوى في الصفحة رقم 1
CORDLESS DRILL KIT-18V
CORDLESS DRILL KIT-18V
Model 44849
ASSEMBLY INFORMATION
ASSEMBLY INFORMATION
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failur
ملخص المحتوى في الصفحة رقم 2
SPECIFICATIONS Battery 18V, Ni-Cd Rechargeable Speed 0-900 RPM, Reversible Torque Settings 6 Chuck 3/8” Keyless Drill Weight 4.3 lb. Length 9” Included Bits 6 Pc. Screw. Set; 6 Pc. Drill Set; Magnetic Extension Bit SAVE THIS MANuAL You will need the manual for the safety warnings and precautions, assembly instruc- tions, operating and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the invoice number on the inside of the front cover. Keep the manual
ملخص المحتوى في الصفحة رقم 3
10. CHECK FOR DAMAGED PARTS. Before using this product, carefully check that this tool will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this tool. Replace or repair damaged or worn parts immediately. 11. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical replacement parts. Only use accessories intended for use with this product. Approved accessories are available from Harbor Fr
ملخص المحتوى في الصفحة رقم 4
the work area, moving the tool from one location to another, handing the tool to another person, etcetera. 8. READ ALL INSTRuCTIONS AND WARNINGS ON THE BATTERY BEFORE CHARG- ING THE BATTERY. 9. TO AVOID ACCIDENTS, CHARGE THE BATTERY THAT IS SuPPLIED WITH THIS PRODuCT ONLY. Do not use a different charger with this battery. 10. TO AVOID DAMAGE TO CABLE AND PLuG, NEVER PuLL THE CABLE TO DISCON - NECT THE CHARGER. Do not use the Charger if the Cable or Plug are damaged. 11. DO NOT TOuCH THE BATT
ملخص المحتوى في الصفحة رقم 5
uNPACKING When unpacking, check to make sure all parts shown on the Parts List (page 10) are included. If any parts are missing or broken, please call Harbor Freight Tools at the number shown on the cover of this manual as soon as possible. To Charge The Battery: 1. The Battery (11) does not come charged from the manufacturer. Before use, you must charge the Battery. FIGuRE A 2. Plug the Battery Charger into the electrical outlet. BATTERY (11) FIGuRE B 3. Insert the Battery (11) into the B
ملخص المحتوى في الصفحة رقم 6
4. The red light on the Charger turns on when you insert the Battery into the Battery Charger, indicating that the electric current is charging the Battery. If the red light does not come on, recheck the Transformer cord connection or try a different electrical outlet. The red light will shut off when the Battery is fully charged, and then the green light will turn back on automatically. 5. The Battery (11) will charge in approximately 1 to 1-1/2 hours. Do not charge the Bat- tery for lon
ملخص المحتوى في الصفحة رقم 7
To Insert And Remove Drill Bits And Drivers: REVERSING SWITCH TRIGGER BATTERY FIGuRE D 1. Set the Reversing Switch (16) to the “LOCKED” (Center) position. (See Figure D.) 2. Hold the Chuck firmly while turning the forward section of the Chuck counterclockwise. This opens the Chuck to accept the drill bit. Insert the drill bit into the chuck fully. 3. Turn the forward section of the Chuck clockwise while holding the Chuck firmly in place to tighten the Chuck around the drill bit shaft. Ma
ملخص المحتوى في الصفحة رقم 8
OPERATING INSTRuCTIONS Note: All parts below refer to the parts listed on pages 11 and 12 of this manual. To Operate The Reversing Switch: 1. The three-position Reversing Switch is located on top of the Trigger. (See Figure D.) 2. When the Reversing Switch is in the center, the Drill is in a “locked” position. 3. When the Reversing Switch is pressed to the right, the rotation of the Drill will be counter- clockwise (typically for removing fasteners or freeing drill bits). 4. When the Reversing
ملخص المحتوى في الصفحة رقم 9
Drill Bit Selection: 1. Always use sharp drill bits. Sharp bits are less likely to bind when drilling. 2. Use the proper bit for the job. There are many types of bits designed for specific purpos- es. Check the information on the bit’s packaging for proper usage. 3. Do not use bits larger than the rated capacity of the drill; gear damage or motor overload may result. Drilling An Object: CAuTION: Do not operate the Drill before placing the Drill Bit on the material. 1. Avoid overloading the
ملخص المحتوى في الصفحة رقم 10
CLEANING AND MAINTENANCE Caution: Always disconnect this tool from its electrical power supply before performing any cleaning, servicing, or maintenance. 1. Keep the Drill exterior free of oil or grease. Use only a mild soap and damp cloth when cleaning. Do not use a flammable or combustible solvent. Do not immerse this product in a liquid or allow a liquid to flow inside the tool. 2. Before each use, examine the general condition of the Drill. Check for loose screws, mis- alignment, bin
ملخص المحتوى في الصفحة رقم 11
PLEASE READ THE FOLLOWING CAREFuLLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UN
ملخص المحتوى في الصفحة رقم 12
PARTS ASSEMBLY #19 Battery Charger (not shown) Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts. Rev 03a SKU 44849 For technical questions, please call 1-800-444-3353. Page 12
ملخص المحتوى في الصفحة رقم 13
ELECTRICAL SCHEMATIC Rev 03a SKU 44849 For technical questions, please call 1-800-444-3353. Page 13
ملخص المحتوى في الصفحة رقم 14
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installa- t
