ملخص المحتوى في الصفحة رقم 1
16 SPEED FLOOR DRILL PRESS
Model 43378
SEt uP AnD OPERAtIng InStRuctIOnS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE tHIS MAnuAL.
ملخص المحتوى في الصفحة رقم 2
Specifications 120 VAC, 60 Hz, 3/4 HP, 1750 RPM; 5.8 amps 36ZJ Motor (with load) E105017 220, 300, 430, 480, 590, 650, 720, 850, 950, 16 Spindle Speeds 1600, 1900, 2000, 2500, 2900, and 3600 RPM Spindle Stroke: 3-1/8 inches; Taper: MT2 Column 2-7/8 (diameter) inches Base Dimensions 10-1/8 x 17-1/2 inches; Slots: 5/8” Throat Depth 6-5/8 inches (of 13 inch swing) Chuck Capacity 7/64 to 5/8 inches; Taper: JT3 Table Slot 5/8 inches Table Rotation 360°; Tilt: 45° (left and right) Table Size 11-5/8
ملخص المحتوى في الصفحة رقم 3
do the work of a larger industrial tool. There are certain applications for which this tool was designed. Do not modify this tool and do not use this tool for a purpose for which it was not intended. 7. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically non-conductive clothes and non-skid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 8. use eye and ear protection. Always wear
ملخص المحتوى في الصفحة رقم 4
19. Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 20. use proper size and type extension cord. If an extension cord is required, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to
ملخص المحتوى في الصفحة رقم 5
VIbRAtIOn HAzARD This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury: 1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical check-ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impair
ملخص المحتوى في الصفحة رقم 6
5. Never place hands and arms near the workpiece to avoid the possibility of the work piece coming loose and striking you. 6. Before drilling, turn on the motor and check for bit wobble or machine vibration. If this is found, correct the problem before drilling. 7. Set the proper spindle speed for the specific drilling operation. 8. When finished with the Drill Press, always press the Switch to the OFF position, and remove the Lock Key. 9. Do not mount (or adjust) the workpiece
ملخص المحتوى في الصفحة رقم 7
Assembly Assembly hardware is located in separate bags. Each bag contains the necessary parts for each assembly step. Remove all packing and protective material from the Drill Press com- ponents. 1. Position the base (B6) on a level floor. It is recommended to bolt the Base to the floor using appropriate hardware (not supplied). Column Support (B4) Hex Screws (B5) Table Crank (B8) Arm Locking Handle (B16) 2. Place the column Support (B4) on the Base, aligning the mounting holes. 3. Insert fou
ملخص المحتوى في الصفحة رقم 8
8. Using two people, lift the Head Assembly up and onto the Column (B1). It should slide down on the Column Tube as far as it will go. Align it so that it faces straight forward, inline with the Base. 9. Screw in two Set Screws (21), into each side of the Head (1) and tighten with the Allen wrench. Head Assembly Hex Screw (17) Washer (15) Belt Tension Lock Knob (18) Hex Nut (14) Belt Tension Motor (13) Lever (19) Head Lock Set Screws (21) 10. Mount the Motor (13) onto the Head Assembly (se
ملخص المحتوى في الصفحة رقم 9
- Push the Motor up until the top of the pulleys align. Hold Motor in place. - Using a wrench, tighten four Hex Nuts (14) supporting the Motor. - Turn the Belt Tension Lever (19) counterclockwise to release belt tension. 13. Install V-belts (A1). Refer to the photos on page 7. - Turn the Belt Tension Lever (19) and move the pulleys closer together. - Place the Idler Pulley (A19) on the Idler Pivot (A20), and into the Pulley Cover center hole (See the Pulley Assembly Drawing at the end of t
ملخص المحتوى في الصفحة رقم 10
Operation Warning: Avoid personal injuries. before operating this machine, review all Safety Warnings and Precautions listed on pages 2 through 5. 1. Loosen the Arm Locking Handle (B16) and turn the Table Crank (B8) to adjust the Table height to accommodate the workpiece being drilled. 2. Open the Chuck and insert the drill bit in the center. Tighten with the Chuck Key (A16). 3. Secure the workpiece (and backup material) to the Table using a vise and/or clamp. The workpiece sits on the backup
ملخص المحتوى في الصفحة رقم 11
2. Mark the desired hole depth on the side of the workpiece. 3. Loosen the Depth Locking Screw Lock. 4. Turn the Feed Handle counterclockwise to bring the tip of the drill bit down, next to the hole depth mark. 5. Turn the Depth Stop Collar counterclockwise until it stops moving. 6. Tighten the Depth Locking Screw. 7. Turn the Drill Press ON and turn the Feed Handle counterclockwise until it drills the hole and stops at the set depth. 8. Turn the Drill Press OFF. using the Depth Scale to Measu
ملخص المحتوى في الصفحة رقم 12
Maintenance Warning: before performing any maintenance to this machine, remove the line cord from the electrical outlet. Removing the chuck and Arbor During this procedure, refer to the Pulley and Spindle Assembly Drawing. 1. Adjust the Depth Stop Collar to hold the Chuck at a depth of three inches. 2. Align the key holes in the Spindle Shaft (A13) and the Quill (A11) by turning the Chuck by hand. 3. Insert the Wedge Drift Key (A17) into the key holes. 4. Lightly tap the Wedge Drift Key with a
ملخص المحتوى في الصفحة رقم 13
6. With the screwdriver still in place, loosen the (inner) Hex Nut (38) until the Quill Spring Cap notch disengages from the Spring Seat (42) -- about 1/8 inch. Quill Spring Cap (39) Hex Nut (38) - Inner Quill Spring Cap Notches Hex Nut (38) - Outer 7. Turn the screwdriver counterclockwise and engage the next Spring Cap notch. Leave the screwdriver in place. 8. Tighten the (inner) Hex Nut just enough to engage the notch. If this Hex Nut is too tight, it will restrict (up and down) Chuck-Arbor
ملخص المحتوى في الصفحة رقم 14
t roubleshooting SYMPt OM POSSIbLE cAuSE SOLutIOn - Incorrect spindle speed - Change spindle speed Drill bit burns or - Dull drill bit - Replace with new bit smokes - Drilling too slowly - Drill faster - Lacking lubrication - Lubricate cutting area - Belt tension set wrong - Adjust belt tension Makes unusual - Spindle dry - Lubricate spindle noise - Loose spindle pulley - Check pulley nut - Loose motor pulley - Tighten Set screws - Bent bit - Replace drill bit - Worn Spindle Bearings - Replace s
ملخص المحتوى في الصفحة رقم 15
Head Assembly Parts List Item # Description Item # Description 1 Head w/pointer and trim 24 Feed Handle 2 Cable Clamp 25 Spindle Feed Shaft 3 Pan Head Screw, M5x12 26 Collar Depth Stop, w/Scale 4 Hex Screw, M8x16 27 Stop Pin 5 Adjusting Lever 28 Connector Wire 6 Motor Support Bracket 29 Lock Washer, Ext., 5mm 7 Motor Support Bracket 30 Pan Head Screw, M5x12 8 Motor Mount 31 Switch 9 Lock Washer, o12 33 Switch Plate Cover 10 Hex Nut, M12x1.75 34 Pan Head Screw, ST4.2x9.5 11 Motor Pulley 35 Switch
ملخص المحتوى في الصفحة رقم 16
Head Assembly Drawing 41 42 SKU 43378 Page 16
ملخص المحتوى في الصفحة رقم 17
Pulley and Spindle Assembly Parts List Item # Description A1 V Belt, M24 A2 Pulley Nut A3 Spindle Pulley A4 Pulley Insert A5 Ball Bearing A6 Spacer A7 Retaining Ring, 17 mm A8 Retaining Ring, 11 mm A9 Ball Bearing A10 Quill Gasket A11 Quill A12 Ball Bearing A13 Spindle Shaft A14 Arbor A15 Chuck A16 Chuck Key A17 Wedge Drift Key A18 Ball Bearing A19 Idler Pulley A20 Idler Pivot A21 Knob A22 Pan Head Screw, M5x8 A23 Pulley Cover A24 Washer, HD Screw, M16x12 A25 Foam Washer Rev 07i SKU 43378 Page 1
ملخص المحتوى في الصفحة رقم 18
Pulley and Spindle Assembly Drawing When ordering a part from this drawing, add an “A” prefix to the part number. Rev 07i SKU 43378 Page 18
ملخص المحتوى في الصفحة رقم 19
base and t able Assembly Parts List Item # Description B1 Column B2 Rack B3 Set Screw, Hex. Socket, M10x12 B4 Column Support B5 Hex Head Screw, M10x40 B6 Base B7 Table Support w/ Indicator B8 Table Crank B10 Gear Pin B11 Set Screw, Socket, M6x10 B12 Bevel Table Lock Screw B13 Table Clamp B14 Arm w/ Scale B15 Table B16 Arm Locking Handle B17 Helical Gear B18 Worm B19 Collar Rev 07i SKU 43378 Page 19
ملخص المحتوى في الصفحة رقم 20
base and t able Assembly Drawing When ordering a part from this drawing, add a “B” prefix to the part number. Rev 07i SKU 43378 Page 20
