ملخص المحتوى في الصفحة رقم 1
Owner's Manual
with Assembly Instructions
For Model M0412
Please read this manual and save it
with your original sales receipt.
Tools needed for assembly: Phillips Screwdriver, Hammer
and Safety Scissors (all not included). Use only with
®
®
a Power Wheels 12 Volt Rechargeable Battery and
®
Power Wheels 12 Volt Charger with Type 12V Connector
(both included).
Cruiser
Product features may var P Product features may var roduct features may vary y from the picture above. y from the picture abov
ملخص المحتوى في الصفحة رقم 2
A T TABLE OF CONTENTS ABLE OF CONTENTS A Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2 B Warnings and Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 C Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ملخص المحتوى في الصفحة رقم 3
WARNINGS AND CAUTIONS B ELECTRICAL HAZARD WARNING • Battery can fall out and injure a child if vehicle tips over. Always use battery retainer. • PREVENT FIRE - Never modify the electrical system. Alterations could cause a fire resulting in serious injury and could also ruin the electrical system. - Use of the wrong type battery or charger could cause a fire or explosion resulting in serious injury. ® ® - Use of Power Wheels components in products other than Power Wheels vehicles could
ملخص المحتوى في الصفحة رقم 4
C PARTS • If you experience a problem with this product, or are missing a part, please call us at 1-800-348-0751, rather than return this product to the store. • Please identify all parts before assembly and save all packaging material until assembly is complete to ensure that no parts are discarded. • Metal parts have been coated with a lubricant to protect them during shipment. Wipe all metal parts with a paper towel to remove any excess lubricant. Exhaust Pipe Set Left - Inner Hal
ملخص المحتوى في الصفحة رقم 5
A TABLE OF CONTENTS PARTS C Long Hex Bushing - 2 Hex Bushing - 2 Right Handlebar Left Handlebar Mirror Clamp Mirror Lens - 2 Handgrips - 2 Axle Bushing - 2 Handlebar Harness 12 Volt Battery 12 Volt Charger Left Mirror Right Mirror Left Shock Set Right Shock Set .354" .437" .354 Cap Nut - 2 .437 Cap Nut - 4 Inner Outer Outer Inner 3 1 #8 x /4" Screw - 63 #8 x /2" Screw - 4 Tachometer Cover Air Cleaner Cover For your convenience, we included extra fasteners! Note: Tighten and loosen all screws wit
ملخص المحتوى في الصفحة رقم 6
D A TABLE OF CONTENTS PARTS PICTURE Note: Some parts shown are assembled on both sides of the vehicle. 44 20 43 44 3 28 18 42 34 32 20 17 35 5 33 2 27 4 29 15 16 11 23 31 26 30 14 9 12 24 13 19 10 25 36 30 4 7 21 14 21 8 22 38 29 41 37 6 1 12 30 39 40 1 Vehicle Frame 12 Wheel Axle - 2 23 Fork Axle 34 Right Mirror Parts Not Shown 2 Vehicle Body 13 Air Cleaner 24 Front Fork Cover 35 Wire Cover 3 #8 x /4" Screw - 63 3 Seat 14 Steering Bushing - 2 25 Fender 36 Horn 1 #8 x /2" Screw - 4 4 Wheel -
ملخص المحتوى في الصفحة رقم 7
BATTERY CHARGING E ELECTRICAL HAZARD WARNING CAUTION • Battery can fall out and injure a child if Use the charger in dry locations only. vehicle tips over. Always use battery retainer. About Thermal Fuses • PREVENT FIRE ® Your Power Wheels 12 volt battery is equipped with a built-in - Never modify the electrical system. thermal fuse. The thermal fuse is a self-resetting safety device Alterations could cause a fire resulting which automatically “trips” and shuts down operation of the in s
ملخص المحتوى في الصفحة رقم 8
E BATTERY CHARGING Battery Retainer B 12V Battery Battery A Charger Connector 2 A • Plug the charger connector into the battery . B • Plug the charger into a standard wall outlet . 1 Notes: - If power flow to the wall outlet is controlled by a switch, make • Loosen the two screws holding the battery retainer to the sure the switch is “ON”. vehicle body. - Use the charger only in a wall outlet. Do not plug the charger • Remove the screws and the battery retainer. Set the battery into
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY F WARNING Vehicle Children can be harmed by small parts, Frame sharp edges and sharp points in the vehicle's Vehicle unassembled state, or by electrical items. Body Care should be taken in unpacking and assembly of the vehicle. Children should not handle parts, including the battery, or help in assembly of the vehicle. Large Rectangular Opening 2 Vehicle 3 • Insert four #8 x /4" screws through the vehicle body and into Body Square the vehicle frame. Make sure the holes in th
ملخص المحتوى في الصفحة رقم 10
F ASSEMBLY Peg Right Exhaust Pipe - Inner Half Vehicle Body Hole Tab Left Footboard Stabilizer Wheel Slots Tab Vehicle Frame Left Side View 4 6 (Right Side) • Fit the tabs on the left footboard into the slots in the left side • Separate the exhaust set pieces. Note the R (right side) and L of the vehicle frame. Make sure both tabs are in the slots. (left side) markings on the inside of each piece. Hint: You may need to squeeze the left footboard in order to • Fit the inner half of the ri
ملخص المحتوى في الصفحة رقم 11
ASSEMBLY F Right Exhaust .437" Pipe - Outer Half Wheel Axle .437 (Large Diameter) Cap Nut 8 • Fit the outer half of the right exhaust pipe (R) to the inner half of the right exhaust pipe. 11 • Separate the fork axle from the two wheel axles. (The fork axle is shorter than the wheels axles.) Set the fork axle aside for Right Exhaust assembly step 33. Pipe • Place a .437 (large diameter) cap nut on a flat surface, inside up. • Fit the end of a wheel axle into the cap nut. • Tap the opposite
ملخص المحتوى في الصفحة رقم 12
F ASSEMBLY Saddlebag Notch Axle Bushing Tab Groove Rear Rear Fork Fork Arm Arm Wheel (with Hex Bushings) 16 • Lift the pretend buckles on a saddlebag to open the saddlebag. • Fit the tab on the back surface of the saddlebag into the notch Back View 14 on one side of the rear fender. 3 • Insert three #8 x /4" screws through the holes on the inside of • Position the vehicle assembly so that the back is facing you. the saddlebag. • While holding the hex bushings in place, position the wheel
ملخص المحتوى في الصفحة رقم 13
ASSEMBLY F Headlight Lens Front Fork Assembly Headlight Center Headlight Assembly Holes Housing 20 18 • Position the headlight assembly with the lens down on a flat surface. • Fit the headlight lens onto the headlight housing. • Fit the front fork assembly onto the back of the headlight 3 assembly, as shown. • Insert three #8 x /4" screws into the headlight lens and tighten. • Insert two #8 x ¾" screws through the center holes in the front fork assembly and into the headlight assembly.
ملخص المحتوى في الصفحة رقم 14
F ASSEMBLY Switch Cover Right Peg Handlebar Switch Grip Area Additional Hole 24 22 • Fit the peg on the right mirror through the hole in the right Right Handlebar handlebar and the switch. • Locate the right handlebar . The right handlebar has an • While holding the two parts firmly together, insert two #8 x ¾" additional hole in the grip area. screws into the switch and tighten. • Fit the switch to the right handlebar, making sure the screw hole in the switch aligns with the screw hole
ملخص المحتوى في الصفحة رقم 15
ASSEMBLY F Front Fork Assembly Handlebar Upper Hole in Harness Front Fork DO NOT insert the plug through End of the lower hole Wire Cover in the front fork! Fork Cover Plug Back View 28 • Turn the front fork assembly around so the back is facing you. • Slide the end of the wire cover into the upper hole in the front fork, as shown. Upper Front View 26 Hole • Position the front fork so that it is upright and facing you. • Insert the handlebar harness plug through the upper hole in Left
ملخص المحتوى في الصفحة رقم 16
MT TM F ASSEMBLY Front View Handlebar B Harness A Handlebar Harness Handlebar Harness See Inset Handlebars 30 Tab 32 • Align the screw holes in each handlebar with the screw holes in the front fork. • First, insert two #8 x ¾" screws through the lower holes in the • Fit the handlebar harness behind the A front fork and into each lower hole in each handlebar and tab in the vehicle frame neck. Tab hand tighten. Do not tighten the screws completely. These screws will be tightened in step
ملخص المحتوى في الصفحة رقم 17
TM TM TM ASSEMBLY F .354 (Small Diameter) Neck of Cap Nut Vehicle Body .354" B A Handlebar Steering Assembly Stop 34 Front Fork 36 Assembly Fork Axle • First, fit the tab on the steering stop into the curved slot in the A lower steering bushing . • Slide the fork axle up through the bottom of the front fork, • Hold the steering stop in place. through the frame neck and steering stop, and out the top of • Then, slide the handlebar assembly on the vehicle frame neck the front fork. B and
ملخص المحتوى في الصفحة رقم 18
F ASSEMBL ASSEMBLY Y F PUSH HERE Tank Seat Tab Seat Tab Tabs Slot Right Side View 38 • Balance the sound box on the vehicle body. (The speaker should face down.) 40 • Fit the tabs at the bottom of the tank under the front end of the vehicle body. • Fit the tab on the front of the seat into the slot near the tank. • Lower the tank on the vehicle frame, making sure that the two • Push down firmly near the back of the seat to “snap” it to small square openings in the tank fit over the buttons o
ملخص المحتوى في الصفحة رقم 19
ASSEMBLY F Tachometer Inner Right Shock Inner Left Shock Fork Cover Outer Left Outer Right Shock Shock 44 • The shock sets may be held together by rubber bands to aid 42 in assembly. After completing assembly step 44, remove and throw away the rubber bands. • Fit the tachometer to the fork cover. • Fit the inner and outer left shock halves together (they are • Insert two #8 x ¾" screws into the tachometer and tighten. labeled on the inside with an “L”). Insert a #8 x ¾" screw into the ho
ملخص المحتوى في الصفحة رقم 20
F ASSEMBL ASSEMBL YY F Wheel 18 18 Guide Guide Guide Guide 20 20 Wheel Axle 21 21 19 19 Shock Shock Front Wheel Wheel (with Long 46 Hex Bushings) 48 • Before applying labels to the front wheel, wipe the wheel with a clean, dry cloth to remove any dust or oils. • While holding the long hex bushings in place, position the • Apply labels to both sides of the front wheel as shown in wheel between the shocks. the illustration. • Being careful to keep the shocks correctly positioned, align the IM
