ملخص المحتوى في الصفحة رقم 1
Operating Instructions and Parts Manual
24-inch Pneumatic Planishing Hammer
Model PH-24T
WALTER MEIER (Manufacturing) Inc.
427 New Sanford Road
LaVergne, Tennessee 37086 Part No. M-756121
Ph.: 800-274-6848 Revision A 05/2011
www.waltermeier.com Copyright © 2011 Walter Meier (Manufacturing) Inc.
ملخص المحتوى في الصفحة رقم 2
Warranty and Service Walter Meier (Manufacturing) Inc., warrants every product it sells. If one of our tools needs service or repair, one of our Authorized Service Centers located throughout the United States can give you quick service. In most cases, any of these Walter Meier Authorized Service Centers can authorize warranty repair, assist you in obtaining parts, or perform routine maintenance and major repair on your JET® tools. For the name of an Authorized Service Center in your area ca
ملخص المحتوى في الصفحة رقم 3
Table of Contents Warranty and Service..........................................................................................................................2 Table of Contents ...............................................................................................................................3 Introduction ........................................................................................................................................3 Specifications for PH-24T Planishing
ملخص المحتوى في الصفحة رقم 4
1. Read and understand the entire owner’s manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3. Replace the warning labels if they become obscured or removed. 4. This planishing hammer is designed and intended for use by properly trained and experienced personnel only. If you are not familiar with the proper and safe operation of a planishing
ملخص المحتوى في الصفحة رقم 5
20. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 21. Do not overreach. Keep proper footing and balance at all times. 22. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for which it was not designed. The right tool will do the job better and more safely. 23. Use recommended accessories; improper accessories may be hazardous. 24. Ma
ملخص المحتوى في الصفحة رقم 6
Specifications for PH-24T Planishing Hammer Model ...................................................................................................................................................................PH-24T Stock Number ...................................................................................................................................................... 756121 Electrical Power: Incoming Power ......................................................................
ملخص المحتوى في الصفحة رقم 7
Features and Terminology Figure 1 - Features 7
ملخص المحتوى في الصفحة رقم 8
Unpacking, Mounting and Assembly Operation 1. With the help of an assistant, carefully Keep hands clear of hammer uncrate the planishing hammer. A tab is and anvil area at all times! Failure to comply welded to the top tube if you choose to use may cause serious injury! a hoist to set up the machine. Referring to Figure 3: 2. Determine the most suitable location for your planishing hammer based on the 1. Connect the air compressor to the quick planned usage of the machine. Larger c
ملخص المحتوى في الصفحة رقم 9
To remove the entire driver from the hammer barrel, push the tab on the air hammer housing and pull down on the driver. To reinstall the hammer drive, orient the notch toward the general direction of the tab, and push driver upward while still pushing back on the tab. When the driver is properly inserted, the tab will snap back into place. Make sure driver and dies are properly inserted before operating machine. Figure 4 6. Plug the planishing hammer into the power supply. 7
ملخص المحتوى في الصفحة رقم 10
Assembly Drawing for PH-24T Planishing Hammer 10
ملخص المحتوى في الصفحة رقم 11
Ordering Replacement Parts To order parts or reach our service department, call 1-800-274-6848 Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately. Parts List for PH-24T Planishing Hammer Index No. Part No. Description Size Qty 1 .................... P H 24T-1 ..................Frame ..............................................
ملخص المحتوى في الصفحة رقم 12
Index No. Part No. Description Size Qty 22 .................. PH24-22 ..................Elbow Air Fitting..........................................1/4" ............................ 1 23 .................. PH24-23 ..................Air Fitting Connector ...................................1/4" ............................ 5 24 .................. PH24-24 ..................Hose Clamp ...............................................Ø10-16 mm ................ 6 25 .................. PH24-25 .......
