ملخص المحتوى في الصفحة رقم 1
WS-8007U
Radio Controlled Moon Phase Clock
Instruction Manual
ملخص المحتوى في الصفحة رقم 2
TABLE OF CONTENTS Topic Page Inventory of Contents/ Additional Equipment 3 About WWVB 3 Quick Set-Up Guide 3 Detailed Set-Up Guide Battery Installation 4 Program Mode Function Buttons 5 Time Zone Setting 5 DST (Daylight Saving Time) Setting 6 Language Selection 6 Time Setting 6 Calendar Setting 7 12/24-Hour Setting 7 Selecting °F or °C 7 Features & Operations Changing the Display Mode 8 The Alarm 8-9 Moon Phase 9 Indoor Temperature 9 Mounting 10 Maintenance & Care 11 Trou
ملخص المحتوى في الصفحة رقم 3
INVENTORY OF CONTENTS 1) WS-8007U 2) Instruction manual and warranty card. ADDITIONAL EQUIPMENT (not included) 1) Two fresh 1.5V AA batteries. 2) Three wall-hanging screws. 3) Appropriate screwdriver for screws. ABOUT WWVB (Radio Controlled Time) The NIST (National Institute of Standards and Technology—Time and Frequency Division) WWVB radio station is located in Ft. Collins, Colorado, and transmits the exact time signal continuously throughout the United States at 60 kHz. T
ملخص المحتوى في الصفحة رقم 4
A) MOON PHASE CLOCK 1) Remove the battery cover, located on the backside of the moon phase clock and directly below the function buttons. 2) Observe the correct polarity, and install 2 AA batteries. 3) Replace the battery cover. Note: After the batteries have been installed a tone will sound, and all the LCD’s (Liquid Crystal Display) will briefly light up. Then the indoor temperature, the date as “1/ 1”, the weekday as “MON”, and the Moon Phase will be displayed. Also, the time wi
ملخص المحتوى في الصفحة رقم 5
Your clock will automatically set up with Eastern Time Zone, Daylight Saving Time On, English for the language, 12 hour clock (AM/PM) and °F for temperature. I) FUNCTION BUTTONS There are 4 function buttons located on the backside of the Moon Phase Clock. The function buttons are labeled: “SET”, “+”, “ALM” and “SNZ”. II) TIME ZONE SETTING 1) Hold down the “SET” button for 2 seconds, the default setting “-5EST” will flash in the Date LCD. 2) Press and release the “+” button to se
ملخص المحتوى في الصفحة رقم 6
IV) LANGUAGE SELECTION FOR THE WEEKDAY 1) The default language “US” will be flashing in the time LCD. 2) Press and release the “+” button to select the desired language. There are 3 languages to select from: US English F French E Spanish 3) Press and release the “SET” button to confirm the language setting and to advance to manually set the time. V) TIME SETTING Note: When the WWVB signal is found, that time will over-ride the manually set time. 1) The hour “12” will be
ملخص المحتوى في الصفحة رقم 7
9) Press and release the “SET” button to confirm the date and to set the weekday. 10) The default weekday “MON” (depends on selected language) will flash. 11) Press and release the “+” button to select the appropriate weekday. 12) Press and release the “SET” button to confirm the calendar settings and to advance to select either 12 or 24-hour time display. VII) 12/24-HOUR SETTING 1) The “12” hour time display will be flashing in the time LCD. 2) Press and release the “+” button to to
ملخص المحتوى في الصفحة رقم 8
2) Press and release the “+” button to set the alarm hour. 3) Press and release the “ALM” button to confirm the hour and to move to set the alarm minutes. 4) The alarm minutes flash. 5) Press and release the “+” button to set the alarm minutes. 6) Press and release the “ALM” button to confirm and to exit the alarm setting mode. Note: The alarm will be automatically set to sound when exiting the alarm- setting mode, indicated by the alarm icon to the right of the time- ((( •))) B) ACT
ملخص المحتوى في الصفحة رقم 9
Waxing Moon Phases Waning Moon Phases New Moon Full Moon Crescent Moon Gibbous First Quarter Moon Last Quarter Moon Gibbous Crescent Moon IV) INDOOR TEMPERATURE The Indoor Temperature appears on the right side of the Date LCD. The temperature is checked every 10 seconds, and updated whenever there is a change. MOUNTING Hanging Holes Function Buttons Foldout Table Stands There are two possible ways to mount the moon phase clock: use of the foldout
ملخص المحتوى في الصفحة رقم 10
II) WALL MOUNTING 1) Using a straightedge, horizontally space at 3- 15/16 of an inch (100.58mm) three screw positions on a wall. 2) Install three mounting screws (not included) into a wall within transmission range—leaving approximately 3/16 of an inch (5mm) extended from the wall. 3) Place the moon phase clock onto the screws, using the hanging holes on the backside. Gently pull the moon phase clock down to lock the screws into place. MAINTENANCE & CARE • Extreme tempera
ملخص المحتوى في الصفحة رقم 11
2) Check batteries. 3) Contact La Crosse Technology. Note: For any questions not answered, contact La Crosse Technology with the contact information found at the end of this instructional manual. SPECIFICATIONS Temperature: Measuring range: 32 °F to 122 °F with 0.2 °F resolution (0 °C to 50 °C with 0.1 °C resolution) Checking intervals: Every 10 seconds Power source: Battery type: 2 x AA, IEC LR6, 1.5V (Alkaline) Battery life: Approximately 12 months Dimensions (L x W x H): 11.4
ملخص المحتوى في الصفحة رقم 12
For warranty work, technical support, or information contact: La Crosse Technology, Ltd 2809 Losey Blvd. S. La Crosse, WI 54601 Phone: 608.782.1610 Fax: 608.796.1020 e-mail: support@lacrossetechnology.com (warranty work) sales@lacrossetechnology.com (information on other products) web: www.lacrossetechnology.com FCC ID: OMO-01RX (receiver) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: 1. THIS D
