ملخص المحتوى في الصفحة رقم 1
Cordless Driver Drill
Equipped with Electric Brake
MODEL 6071D
MODEL 6071DW
With Fast Charger
MODEL 607lDWK
With Fast Charger and Carrying Case
INSTRUCTION MANUAL
SPEC IF I CAT IONS
Cdpacitics
-
No load speed Dimensions IL x W x HI Net weight
Stcel Wood Wood screw
10 11111, 4 5 mm x 20 mini 1 ~~ 6oo R,m,n I 220 mm x 49 mm x 215 mm 115kg
13 a"! 1 13'16" x 3 4"1 (8~518" x 1 7'8" x 8 1!2"1 1 12 5 Ibs!
Battery Cartridge 7000 1 - Model DC7100 Fast Charger
Dimensions Net
IL x W x HI 1
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
ملخص المحتوى في الصفحة رقم 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't operate tool when you are t
ملخص المحتوى في الصفحة رقم 4
IMPORTANT SAFETY INSTRUCTIONS 1. SAVE THESE INSTRUCTIONS - This manual 25 50 100 150 Length of Cord (Feet) AWG Size of Cord 18 18 18 16 9. Do not operate charger with damaged cord or plug - replace them im- mediately. IO. Do not operate charger if it has received a sharp blow, been dropped, or other- wise damaged in any way; take it to a qualified serviceman. 11. Do not disassemble charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incor
ملخص المحتوى في الصفحة رقم 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (5OOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. Do not short the battery cartridge: (1) Do not touch the terminals with any condu
ملخص المحتوى في الصفحة رقم 6
Installing or removing battery cartridge 0Always switch off the tool before inser- tion or removal of the battery cartridge. j .To remove the battery cartridqe, pull out the set plate on the bottom if the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery cartridge with the it into groove in the housing and slip place. Snap the set plate back into place. Be sure to close the set plate ful
ملخص المحتوى في الصفحة رقم 7
Selecting correct Phillips bit Nominal diameter (mm) Use the chart to determine the best size Bit No. Wood screw that you driver bit for the size of screw 2.1 - 2.7 (3/32" - 1/8") wish to use. No. 2 3.1 - 4.5 (118"- 3/16") Selecting slotted bit Use a slotted bit that properly fits the screw slot. Use of a bit that is too small will damage the screw and/or bit. Installing or removing driver bit CAUTION : Always be sure that the tool is switched off and the battery cartridge is remov
ملخص المحتوى في الصفحة رقم 8
to stop. CAUTION : Before inserting t..e battery cartridge into the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Reversing switch action This tool has a reversing switch to change the direction of rotation. Slide the revers- Reversing switcd ing switch to the right for clockwise rota- tion or to the left for counterclockwise. CAUTION : 0 Always check the direction of rotation before operation. .Use the reversing
ملخص المحتوى في الصفحة رقم 9
Bubble level This tool is equipeed with a bubble level to Bubble level aid in holding the tool horizontally. Simply center the bubble in the sight window. 7 Screwdriving operation Place the point of the driver bit in the screw head and apply pressure to the tool. Start the tool slowly and then increase the speed gradually. Release the trigger just as the screw bottoms out. The electric brake will then stop the tool immediately, pre- venting the screw and/or bit from being damaged.
ملخص المحتوى في الصفحة رقم 10
Drilling operation 0 Drilling in wood When drilling in wood, best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. 0 Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a centerpunch and hammer at the point to be drilled. Place the point of the bit in the indentation and start drilling. Use a cutting lubricant when drilling metals. The exceptions
ملخص المحتوى في الصفحة رقم 11
MAINTENANCE CAUTION : Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11
ملخص المحتوى في الصفحة رقم 12
ACCESSORIES CAUTION : These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons, be used only in the proper and intended manner. The accessories or attachments should Bits Fast charger Model DC7100 Part No. 113109-0 0 Rubber pad assembly 0 Battery cartridge 7000 Part No. 632002-4 Part No. 123001 -2 0 Wool bonnet 0 Battery cover Part No. 743401-6 Pa
ملخص المحتوى في الصفحة رقم 13
0 Tool holster 0 Battery holster has some bits storage space Holster holds extra battery Use holster to carry drill only after Part No. 823033-3C removing bit. Part No. 823033-3A Part No. 823033-3E (Genuine holster) 0 Steel carrying case Part No. 823087-3 (Steel case) Part No. 181372-3 (Plastic Case) 13
ملخص المحتوى في الصفحة رقم 14
10 mm (3/8") CORDLESS DRIVER DRILL Model 6071D Note: The switch and other part configurations may differ from country to country. MODEL 6071D 1 14
ملخص المحتوى في الصفحة رقم 15
MOUEL 6071U Apr 21 86 EN 'EM A&, DESCRIPTION ,,!& DESCRIPTION Drill Chuck S10 la I Tube Pan Head Screw M5x18 11 7 Pan Head Screw M4x22 IWilh Wdhherl 12 1 Gear set Plat0 Plane Bearing 5 13 1 Houstng L 14 Motor 1 Swrtch Holder 6 15 1 Plane Bearing 3 Swmh 16 1 Gear Couplele 13 58 17 Housing R 1 Plane Bearing 3 I Bubble Level 18 1 Name Plate ~ Note The switch and other part speclflcalions m,iy differ fronl country to country 15 I:,',"
ملخص المحتوى في الصفحة رقم 16
f’ MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every hlakita tool is thoroughly inspected and tested before leaving the factory. It IS warranted to he free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any troubkdevelop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or ma
