ملخص المحتوى في الصفحة رقم 1
C
E
N
R
G
OF F
T
I
PROPANE PATIO HEATER
WARNING: For Outdoor Use Only.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
2. Extinguish any open flame.
3. if odor continues ,immediately
call gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or
other flammable vapors or liquids
in the vicinity of this or any other
appliance.
CAUTION: Retain these instructions
for future use.
C E R T I F I E D
Model No.:SRPH02S
Master Contract N
ملخص المحتوى في الصفحة رقم 2
TOOLS AND PARTS NEEDED FOR ASSEMBLY CARBON MONOXIDE HAZARD DANGER This appliance can produce carbon monoxide which has no odor. Using it in an enclosed space can kill you. Never use this appliance in an enclosed space such as a camper, tent, car or home. TOOLS NEEDED: WARNING: Improper installation, adjustment, alteration, services or maintenance can cause injury, 7/16 Wrench " death or property damage. 3/8 Open " End Wrench Read the installation, operating and maintenance Adjustable
ملخص المحتوى في الصفحة رقم 3
PARTS 9 1 Center Reflector Cap 1 10 4 Reflector Cap 2 1 1 Head Assembly 3 4 1 Gas Hose 2 5 1 Post 1 Cylinder Cover 6 15 16 7 3 Post Mounts 1 Cylinder Base 8 9 15 M6 Nuts 3 18 6mm Washers 10 6 5mm Washers 11 12 5 4mm Washers 13 x 5 M4 8 Bolts 4 14 6 M5 8 B x olts 13 5 15 x 12 M6 10 Bolts 16 3 M6 x70 double pointed bolts 17 1 Regulator 1 Cylinder (Not Supplied) 18 6 9 10 11 12 14 13 7 14 15 1
ملخص المحتوى في الصفحة رقم 4
PRECAUTIONS NOTE: PLEASE READ THE FOLLOWING SAFETY RULES At least once a year, the unit should be inspected for the WARNING presence of spiders, spider webs or other insects. Check the This appliance must only be used outdoors. Using this product in an enclosed area may cause heater immediately if any of the following exist: injury, death or property damage. 1. The smell of gas in conjunction with extreme yellow Read the instructions before use. colored tips of the burner flames. This applian
ملخص المحتوى في الصفحة رقم 5
IGNITER BATTERY INSTALLATION Instruction For Battery Installing Remove igniter button by turning counter clockwise. Install “AAA” battery with positive terminal up as indicated in diagram. Replace igniter button. Ignition button Control knob Replace Battery Ignition button AA battery 5
ملخص المحتوى في الصفحة رقم 6
ASSEMBLY NOTE: Assembly of this heater requires Step 1 basic mechanical skills. Proper assembly is the responsibility of the installer. 5 Step 1 ---- Attach Post to Base Assembly Attach the post to the post mounts using M5 X 8 bolts (6 pcs) and 5mm washers (6 pcs) 14 11 7 Step 2 ---- Attach Cylinder Cover to Post Mounts Step 2 Attach the cylinder cover to the post mounts by sliding over post as indicated. 6 7 6
ملخص المحتوى في الصفحة رقم 7
ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly Step 3 is the responsibility of the installer. Step 3 ---- Attach Head Assembly to Post 3 Load head assembly by inserting gas hose into post. Insert head assembly into post. Tighten securely using M4 X 8 Bolts (5 pcs) and 4mm washers (5 pcs). 4 13 12 5 Step 4 Step4 ---- Attach Double Threaded Bolts to Head Assembly 10 Attach M6 X 70 double threaded bolts (3 pcs) and 6mm washers (3 pcs) to the top of he
ملخص المحتوى في الصفحة رقم 8
ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly Step 5 is the responsibility of the installer. 9 10 1 Attach Center Reflector to Reflector Step 5 ---- Attach center reflector to the top of reflector (4 pcs) with M6 X 10 mm screws (12 pcs), 6mm washers (12 pcs) and nuts (12 pcs). 15 2 Step 6 ---- Attach Center Reflector and Reflector to the top of Head Assembly Step 6 9 Attach center reflector and reflector to the top 10 of head assembly by sliding over
ملخص المحتوى في الصفحة رقم 9
ASSEMBLY NOTE: Assembly of this heater requires basic mechanical skills. Proper assembly Step 7 is the responsibility of the installer. Step 7 ---- Connect Gas Line to Cylinder Attach Gas hose to regulator with 3/8 inch open end wrench and adjustable wrench. Attach regulator to cylinder. Tighten securely. Move cylinder to the plate of base assembly. Step 8 Step 8 ---- Check for leaks Your Patio Heater has been checked at all factory connections for leaks. To check the connection of the gas
ملخص المحتوى في الصفحة رقم 10
ASSEMBLY Step 9---- Lower Cylinder Cover onto Cylinder Base Step 9 Lower the cylinder cover onto the cylinder base . 6 8 Step 10---- Disconnect Cylinder When Storing or Transporting Step 10 1) Turn off the heater. 2) Raise the cylinder cover onto the post mounts. 3) Turn off the valve on the cylinder. 4) Disconnect the regulator from the cylinder. 6 7 10
ملخص المحتوى في الصفحة رقم 11
n n r r u u t t o o t t h h s s u u L L P P O O W W F F F F O O OPERATION WARNING: DO NOT attempt to operate heater until you have WARNING read and understand all precautions. Failure to do so can result in serious personal injury, death or property damage. FOR YOUR SAFETY: If at any time you are unable to light Before Turning Gas Supply ON burner and smell gas, wait 5 minutes to Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a allow gas to dissipate be
ملخص المحتوى في الصفحة رقم 12
n n r r u u t t o o t t h h s s u u L L P P O O W W F F F F O O OPERA OPERATION TION Note: The flame pattern at the emitter grid should be visually checked whenever the heater is operated. Normally the burner flame is blue, but little yellow flame is acceptable. If flames extend beyond the surface of the emitter grid, flame is lifting off the or there is a black soot (carbon) accumulating on the emitter grid or reflector, the heater should be turned off immediately. The heater should not
ملخص المحتوى في الصفحة رقم 13
LOCATING HEATER FOR USE BE CAREFUL: WHEN CERTAIN MATERIALS OR ITEMS ARE Stored, ABOVE, BESIDE OR UNDER THIS HEATER WHILE IN USE, THEY WILL BE SUBJECT TO RADIANT HEAT AND COULD BE SERIOUSLY DAMAGED. 36" This heater is primarily used for the heating of outdoor patios, decks, pool and spa areas. Always make sure that adequate fresh air ventilation is provided. Follow the spacing 24" 24" tolerances shown in Figure 1. The minimum clearances, shown in Figure 1, must be maintained at all times. The
ملخص المحتوى في الصفحة رقم 14
MAINTENANCE/CLEANING/STORAGE MAINTENANCE : Visually check To enjoy years of outstanding performance from your heater make sure you perform the following maintenance activities on a regular basis: Keep exterior surfaces clean. Emitter Screen Use warm soapy water for cleaning. Never use flammable or corrosive cleaning agents. While washing your unit, be sure to keep the area around the burner and pilot assembly dry at all times. If the gas control is Yellow Tip exposed to water in any way, DO NO
ملخص المحتوى في الصفحة رقم 15
TROUBLESHOOTING PROBLEM PROBABLE CAUSE SOLUTION Pilot will not light Gas valve may be OFF Turn the gas valve ON Fuel Tank empty Refill LP gas tank Orifice blocked Clean or replace orifice Purge air from lines, with knob Air in supply system in pilot position, depress and hold in, to release air. Loose connection Check all fittings Dead battery Replace battery Pilot will not stay on Debris around pilot Clean dirty area Loose co
