ملخص المحتوى في الصفحة رقم 1
OWNER'S MANUAL
AERATO R SPREADER
MODEL:
AS-30 BH
AS-40 BH
Assembly
Installation
Operation
Repair Parts
For use with Lawn/Garden
Tractors
For the latest product updates and setup tips:
Important: This manual contains information for the safety of
Visit us on the web!
persons and property. Read it carefully before assembly and
www.brinly.com
operation of the equipment!
L-1711-BH.-3
ملخص المحتوى في الصفحة رقم 2
CONGRATULATIONS on your new Brinly-Hardy Lawn Aerator. It has been designed, engineered, and manufactured Keep all nuts, bolts and screws tight to be sure the equipment to give you the best possible dependability and performance. is in safe working condition. Should you experience any problem you can not easily The vehicle and attachment should be stopped and inspected remedy, please do not hesitate to contact our knowledgable for damage after striking a foreign object. The damage customer
ملخص المحتوى في الصفحة رقم 3
REFERENCE Tools Required for Assembly: * ½" wrench (2) * 3/4" wrench (2) * Pair work gloves OR * Hammer * 10" Adjustable wrench (2) A note about nuts used in the assembly of your Aerator Spreader: 1. Jam Nuts and Hex Nuts spin freely on the bolt threads. Usually a lock washer is used to lock the nut securely in place. Hex Nut Jam Nut 2. Lock Nuts and Nylon Lock Nuts provide resistence after several turns on the bolt threads. A wrench is normally req
ملخص المحتوى في الصفحة رقم 4
51 37 13 53 34 54 7 11 2 30 6 27 44 52 40 15 10 8 25 23 44 40 56 1 4 33 37 50 38 12 49 18 20 57 46 52 36 23 44 44 1 14 3 55 46 40 40 24 31 40 44 31 58 27 21 11 39 2 20 9 13 40 43 17 52 48 44 35 34 37 16 26 19 22 41 5 42 45 29 47 41 47 32 28 47 Parts Reference 4. L-1711-BH.-3
ملخص المحتوى في الصفحة رقم 5
Parts List AS-302 AS-402 REF. NO. DESCRIPTION QTY. PART NO. R-774 1 R-774 Flat Washer - Large 2 B-1674P *2 B-1674P 5/16" Hex Lock Nut 3 B-6520 *3 B-6520 Transport Lock 1 B-4030 4 B-4030 1/4" Wing Nut 1 B-6407 5 B-6407 Aerator Tine Assembly 8 or 11 B-5922 6 B-5922 Brinly Logo Decal 1 B-4701-10 7 B-5718-10 Hopper Assembly 1 K-653 8 K-654 Agitator Kit (Hwd.Incl.) 2 B-5474-10 9 B-5720-10 Agitator Shaft Assembly 1 B-4709-10 10 B-5726-10 Shutter Assembly 1 B-4713 11 B-4713 1/2" Washer
ملخص المحتوى في الصفحة رقم 6
Figure 1. Tighten securely Nut to be tight against tube not against wheel. Qty. 4 (41)Hex Jam Nut, 1/2" Qty. 2 (45)Lock Washer, 1/2" Qty. 6 Wheel to turn Qty. 2 (47)Flat Washer, 1/2" (32)Hex Bolt, 1/2" x 3-1/2" freely. Figure 2. Qty. 4 (34)Hex Bolt, 5/16" x 2" Hopper Towbars Qty. 4 Qty. 4 (44)Lock Washer, 5/16" (40)Hex Nut, 5/16" 6. L-1711-BH.-3
ملخص المحتوى في الصفحة رقم 7
Figure 3. Qty. 2 (37)Hex Bolt, 5/16" x 3" Qty. 2 Qty. 2 (40)Hex Nut, 5/16" (44)Lock Washer, 5/16" Qty. 1 Towbars (50)Drawbar Pin 1/2" x 2-1/2" Qty. 1 (51)Hairpin Cotter (NOT TO SCALE) Figure 4. Qty. 2 Qty. 2 (46)Flat Washer, 5 /16" (31)Hex Bolt, 5/16" x 3/4" Hopper Transport Plate Qty. 2 (40)Hex Nut, 5/16" Qty. 2 (44)Lock Washer, 5/16" L-1711-BH.-3 7.
ملخص المحتوى في الصفحة رقم 8
Figure 5. Towbars Qty. 2 (13)Cap Tube Qty. 2 (37)Hex Bolt, 5/16" x 3" Qty. 2 (2)Hex Lock Nut, 5/16" Do not over tighten nut, Wheel Support must pivot. Wheel Support Figure 6. Install Grip (not shown) Wheel Support Lift Handle Qty. 2 (40)Hex Nut, 5/1 Qty. 2 (42)Carriage Bolt, 5/16" x 1-3/4" Qty. 2 (44)Lock Washer, 5/16" 8. L-1711-BH.-3
ملخص المحتوى في الصفحة رقم 9
Make sure Lever points Figure 7. forward. Install Grip (not shown) Qty. 1 (31)Hex Bolt, 5/16" x 3/4" Qty. 1 (44)Lock Washer, 5/16" Qty. 1 (40)Hex Nut, 5/16" OPERATION WHEN TO USE: The recommended operating speed is slightly faster than a Your Aerator-Spreader should not be used when lawn brisk walk- 3 to 5 MPH. Set the throttle/gear selector to conditions are too wet or too dry. This can be determined by obtain this speed. To obtain this speed Calibrate your tractor digging a small amount
ملخص المحتوى في الصفحة رقم 10
OPERATION Continued... Set the spreader flow control at the approximate flow control setting. FLOW CONTROL ADJUSTMENT Place 5 pounds of material in the Hopper. Weigh the Open and Close: The material flow is shut off by moving material before and after spreading 100 square feet to Control Lever to the left and locking into "V" notch on determine amount of material used. calibration plate. Move unit to measure area, lower aerator tines, open Flow Control Lever. Drive the 40 ft. course, stop
ملخص المحتوى في الصفحة رقم 11
Limited Warranty Brinly-Hardy Company warrants only to the original retail purchaser that this product will remain free of defects in workmanship and materials under normal use and service for a period of two (2) years (NOTE: ninety (90) days for commercial or rental use) commencing with the date of purchase. Any parts found to be defective within the warranty period will be replaced, with proof of date of purchase, at Brinly-Hardy Company's expense. Our obligation under this warranty is expr
