ملخص المحتوى في الصفحة رقم 1
Users Manual
RemotePoint Onyx
Page 1
ملخص المحتوى في الصفحة رقم 2
Thank Yuo Thank you for purchasing a RemotePoint Onyx Presentation Remote. We know you had other choices and we appreciate that you chose Interlink Electronics by SMK-Link for your wireless needs. So that we may better serve you in the future, please register online at www.smklink.com/register. Wnarra T Y 30-Day Money Back Guarantee 2-Year, Limited Warranty Page 2
ملخص المحتوى في الصفحة رقم 3
FCC Certification This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a CLASS B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection agai
ملخص المحتوى في الصفحة رقم 4
Notice: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Extension cables are not recommended, if used, they must be shielded in order to comply with the emission limits. IC Certification The term “IC” before the certification/registration number only signifies that the Industry Canada technical specifications were met. Declaration of conformity Manufacturer: SMK-Link Electronics, Inc.
ملخص المحتوى في الصفحة رقم 5
Connecting the USB Receiver • Remove the USB receiver from the remote. • Insert the USB receiver into any available USB port on the computer. Computer You can use a USB extension cable for computers with difficult to reach USB ports or to reposition the receiver. Page 5
ملخص المحتوى في الصفحة رقم 6
Installing the Batteries Step 1: Take out the USB receiver or plug Remove receiver or plug prior to installing batteries. Cover can not be removed when inserted. Step 2: Open Remote Turn the remote upside down and push on the eject slider to release the outer cover. Step 3: Remove Cover Separate the outer cover from the remote by gently pulling on the top and bottom in opposite directions. Once separated, turn the remote over. Page 6
ملخص المحتوى في الصفحة رقم 7
Step 4: Add Batteries O p e n t h e b a t t e r y compartment by pressing down on the latch. Insert the batteries per the diagram on the remote. Step 5: Set the Clock Set the clock by pressing the clock set button. The hour will start blinking. Use the following keys to set the time. Increase value Decrease value Move to next digit Done For PC users, there is a Clock Setting Utility available at http://www.smklink.com/support/downloads.html Page 7
ملخص المحتوى في الصفحة رقم 8
Step 6: Reassemble Reassemble your remote by closing the battery door and sliding the outer cover over the remote until it clicks into place. Presenting Next Slide: Advance to the next slide. Previous Slide: Return to the previous slide. Start Presentation: Press this to start your presentation. Starts from your current posi- tion. Blank Screen: Use the blank screen button to hide your presentation while you make a key point. Press again to reveal the presen- tation. Page 8
ملخص المحتوى في الصفحة رقم 9
Using the Laser Pointer Press the button on the front of the remote to activate the laser pointer. The laser pointer can be used to highlight important points on slides and graphs. Using with a Macintosh The remote control has three different compatibility modes. The light on the USB receiver will blink one to three times every second or so to tell you which mode your receiver is currently set to. Mode 1: Windows computers running Microsoft PowerPoint. Mode 2: Macintosh computers
ملخص المحتوى في الصفحة رقم 10
To switch modes you will need a pointy object, such as a paper clip. While the receiver is plugged into a USB port, press down on the recessed button on the receiver. Each time you press the button, it will move to the next mode. Once set, the mode is remembered for next time. Troubleshooting Problem: When you plug the receiver into the remote the light on the next slide button blinks repeatedly for several minutes. Solution: The remote and the receiver are unable to pair. Unplug the r
ملخص المحتوى في الصفحة رقم 11
For Product Support Please Contact SMK-Link Electronics 3601-B Calle Tecate Camarillo, CA 93012 USA TEL 888 696 3500 FAX 805 987 6665 SMKLINK.COM P/N 94-01441 Rev. C Page 11
