ملخص المحتوى في الصفحة رقم 1
M-855
Industrial
Motherboard
User’s Manual
Recycled Paper
60070024IHA00
ملخص المحتوى في الصفحة رقم 2
ملخص المحتوى في الصفحة رقم 3
© Copyright 2004 ADLINK Technology Inc. All Rights Reserved. Manual Rev. 1.00: August 16, 2004 The information in this document is subject to change without prior notice in order to improve reliability, design, and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advis
ملخص المحتوى في الصفحة رقم 4
Getting Service from ADLINK Customer Satisfaction is top priority for ADLINK Technology Inc. If you need any help or service, please contact us. ADLINK TECHNOLOGY INC. Web Site http://www.adlinktech.com Sales & Service Service@adlinktech.com TEL +886-2-82265877 FAX +886-2-82265717 Address 9F, No. 166, Jian Yi Road, Chungho City, Taipei, 235 Taiwan Please email or FAX your detailed information for prompt, satisfactory, and consistent service. Detailed Company Information Company/Orga
ملخص المحتوى في الصفحة رقم 5
Table of Contents Chapter 1 Introduction.................................................................................1 1.1 Unpacking Checklist .................................................................2 1.2 Features .....................................................................................3 1.3 System Block Diagram.............................................................5 1.4 Specifications...........................................................................
ملخص المحتوى في الصفحة رقم 6
ملخص المحتوى في الصفحة رقم 7
1 Introduction ® The M-855 series combines the high performance and exceptional value of the Intel ® 855GME chipset with a full-featured, next generation, industrial board. The Intel ® ® 855GME advanced chipset supports socket 478-pins Intel Pentium M processors ranging from 1.30GHz to 1.80GHz, and up to 2GB DDR SDRAM memory on its ® 400/533MHz FSB. It includes an integrated LVDS and VGA, an onboard Intel 82541 Gigabit Ethernet controller (supporting 10/100/1000 Base-TX Ethernet), audio
ملخص المحتوى في الصفحة رقم 8
1.1 Unpacking Checklist 1. Take out the M-855 series unit from the carton box, check if the unit is properly secure in its plastic bag. 2. Check the contents of the carton box: Industrial Board Installation Guide ATA-66/100 HDD ribbon cable Floppy ribbon cable S-ATA & Power cable (1 Set) Driver CD COM3 ribbon cable (1 Set) External K/B & M/S cable (for RS-232/422/485) (6-pin to 6-pin) 2 • Introduction
ملخص المحتوى في الصفحة رقم 9
Low profile heat sink with fan I/O Shield Note: M-855 OEM versions with non-standard configurations may vary in function or contents according to request. CAUTION: This board must be protected from static discharge and physical shock. Never remove any of the socketed parts except at a static-free workstation. Use the anti-static bag shipped with the ! product to handle the board. Wear a wrist strap grounded through one of the system's ESD Ground jacks while servi
ملخص المحتوى في الصفحة رقم 10
56.05 16.80 29.50 25.42 21.75 6.50 6.22 11.96 38.10 35.97 26.13 21.64 Figure 1: I/O back panel layout M-855 Series Overview Function M-855 ® Chipset Intel 855GME LVDS VGA Gigabit Ethernet 40-pins EIDE interface 2 Type II CF socket 1 Parallel ports 1 Serial ports 4 PCI slots 3 USB 2.0 ports (two for USB cable) 6 Audio Line-out pin-header 1 Fan connector 2 4 • Introduction
ملخص المحتوى في الصفحة رقم 11
1.3 System Block Diagram Socket 478-pins for VRM Clock Intel Pentium M ADDR CTRL DATA 400/533 MHz FSB LVDS or VGA LCD / CRT GMCH (855GME) Device DDR266/333 X2 732 Micro FCBGA IDE Primary Intel ATA100 AC97 82541 Audio 10/100/1000 Codec IDE Secondary Base-TX ICH4 CF Socket 421 BGA USB2.0 USB Port 0/1 PCI BUS USB Port 2/3 USB Port 4/5 S-ATA S3112 Super I/O W83627HF FWH SATA Port 1/2 FINTEK F81216D Keyboard Mouse Floppy COM1/2 LPT Port COM3/4 Figure 2: System Block Diagram Introduction
ملخص المحتوى في الصفحة رقم 12
1.4 Specifications Processor: ® ® - Intel Pentium M processor with socket 478-pins package - Processor operating at 1.3GHz and up to 1.8GHz - System bus frequency at 400 / 533 MHz FSB ® Make sure you use the correct CPU (Pentium M processor). Using a standard Pentium® 4 CPU may crash the system. Chipset: ® - Intel 855GME + ICH4 AGPset DRAM Module: - 2 x 184-pin DIMM socket - DDR 266/333 memory - Support DDR SDRAM up to 2GB (max.) LVDS & VGA: ® - Intel 855GME Chip
ملخص المحتوى في الصفحة رقم 13
Rear I/O Connectors: - PS/2 Mouse and PS/2 style Keyboard - D-Sub 25-pins Printer port connector D-Sub 9-pins COM1 Serial port connector for RS-232 D-Sub 15-pins VGA connector - 2 x USB2.0 connectors - RJ-45 Ethernet and 2 x USB2.0 connectors - Audio for Line-In, Line-Out, MIC phone jack (Optional) Internal I/O Connectors (pin-header): - 3 x Serial ports, COM2 for RS-232 and COM3 / 4 for RS-232/422/485 (Serial cable with bracket) - 2 x USB2.0 connectors (USB cable with bracket
ملخص المحتوى في الصفحة رقم 14
ملخص المحتوى في الصفحة رقم 15
OPEN CLOSED OPEN CLOSED 2 Installation 2.1 System Installation CPU Installation Carefully follow the steps below to install the CPU: 1. Check and confirm that the jumpers are correctly set for the CPU you are going to install (figure 3). 2. Take the screwdriver and releasing screw-nut of the Socket 478. 3. Rotate mark of screw-nut to face the “OPEN”. 4. Align the pins of the CPU against the pinholes of the Socket 478. Be sure to pay attention to the orientation of the CPU.
ملخص المحتوى في الصفحة رقم 16
8. Push down the opposite side of the ZIF clip and hook it. 9. Connect the cooling fan cable to the socket as shown below. Be careful not to place the cable on the CPU cooling fan. Removing a CPU: 1. Before removing the CPU, turn off the power and wait for about 20 minutes until the heat radiation plate of the cooling fan and the CPU cools down. 2. Rotate mark of screw-nut to face the “OPEN”. 3. To remove the CPU. WARNING: The CPU and the heat radiation plate are hot and can
ملخص المحتوى في الصفحة رقم 17
Figure 5 display the notch marks and what they should look like on your DIMM memory module. DIMMs have184 pins and two notches that will match with the onboard DIMM socket. DIMM modules are installed by placing the chip firmly into the socket at a 90-degree angle and pressing straight down (figure 6) until it fits tightly into the DIMM socket. Figure 5: DIMM Memory and 184-pins Socket Figure 6: Memory Installation Carefully follow the steps below i
ملخص المحتوى في الصفحة رقم 18
To remove the DIMM, use your fingers or a small screwdriver to carefully push away the plastic tabs that secure the DIMM at each end. Lift it out of the socket. Make sure you store the DIMM in an anti-static bag. Only use the same size and manufacturer of memory modules. Setting Jumpers and DIP Switches There are jumpers and DIP-switches on the M/B of the M-855 Series. The jumpers can be set for various operations. Figure 7: Jumper Connector For any three-pin
ملخص المحتوى في الصفحة رقم 19
2.2 Board Layout CN1 CN2 CN4 CN6 CN3 CN5 (Optional) CN7 CN8 CN9 DIMM1 DIMM2 CN13 CN14 JP1 JP2 CN15 CN25 JP3 CN10 CN11 CN12 CN16 CN17 CN18 SATA1 CN19 SATA2 JP4 JP7 CF II JP5 CN21 JP6 CN22 CN20 CN24 CN23 Figure 8: Jumper and Connector Locations Installation • 13
ملخص المحتوى في الصفحة رقم 20
2.3 Jumper Settings Jumper Location Description: Use the information in the following table to change the jumpers and the DIP switches. Jumpers Functions JP1 COM3 Port Setting Select JP2 COM4 Port Setting Select JP3 CPU Type Setting Select JP4 Watchdog Timer Setting Select JP5 Clear CMOS Setting Select JP6 Power Management Setting Select A description on setting the jumpers to enable/disable or change functions is illustrated below. Please refer to the diagrams below for jump
