ملخص المحتوى في الصفحة رقم 1
USER’S GUIDE
COLOR MONITOR
Model No : 910TF
CTL
S/N : 9978626520
ملخص المحتوى في الصفحة رقم 2
IMPORTANT SAFEGUARDS FEDERAL COMMUNICATIONS COMMISSION 1. Read all of these instructions. 12. For added protection for this RADIO FREQUENCY INTERFERENCE STATEMENT monitor during a lightning storm, 2. Save these instructions for later use. or when it is left unattended and unused for long periods of time, NOTE : This equipment has been tested and found to comply with the limits 3. Unplug this monitor from the unplug it from the wall outlet. This wall outlet before cleaning. Do not for a Class
ملخص المحتوى في الصفحة رقم 3
CONTENTS INTRODUCTION This manual explains how to correctly install, operate and get the Introduction ............................................................................. 1 best performance from your monitor. Please read this user’s Product Features ................................................................. 2 guide carefully before installing your monitor, then keep it near your monitor for quick reference. Setup .................................................................
ملخص المحتوى في الصفحة رقم 4
SETUP PRODUCT FEATURES CONNECTING THE SIGNAL CABLE AND POWER • The convenient and user-friendly on-screen display allows for CORD easy and accurate adjustments of horizontal and vertical screen size and position, geometry and screen color. 1. Turn off the computer and monitor. • The monitor supports a safe working environment in strict compliance with the MPR II standard for low emissions. 2. Connect the 15 pin D-sub connector to the output port of the
ملخص المحتوى في الصفحة رقم 5
OPERATION & ADJUSTMENT Key Process Control Panel ENGL SH DEUTSCH ESPAÑOL FRANCA S TAL ANO • Move cursor to the right window on the OSD window. • Increase the value of any selected function. • Move cursor to the left window on the OSD window. • Decrease the value of any selected function. • Launch OSD(On-Screen Display) MENU window. MENU • Move cursor to the high window on the OSD Start window. • Increase the value of V.size or V.center. • Move cursor to the low window on the OSD window. • D
ملخص المحتوى في الصفحة رقم 6
OSD Functions ICON CONTROL FUNCTION ICON CONTROL FUNCTION Adjust the horizontal picture moire H. MOIRE cancellation. LANGUAGE Select language for OSD (5 languages). Adjust the vertical picture moire V. MOIRE cancellation. Adjust the position of the display H. CENTER & horizontally(left or right) and vertically V. CENTER (up or down). FOCUS Adjust the focus image. Choose different preset color temperatures COLOR TEMP or set your own customize
ملخص المحتوى في الصفحة رقم 7
SPECIFICATIONS ICON CONTROL FUNCTION CDT Size 19-inch DynaFlat Display horizontal & vertical frequency STATUS Diagonal visible image area 18-inch and polarity. Dot Pitch 0.25 mm YES : VESA DPMS operation. Synchronization Horizontal 30 - 95 KHz POWER SAVER NO : NO DPMS operation. Vertical 50 - 160 Hz Plug and Play DDC1/2B/CI Display a RGB Color Bar to determine TEST PATTERN whether the screen color is expressed Power Saving EPA, VESA DPMS, Nutek Compliant normally or not
ملخص المحتوى في الصفحة رقم 8
DESCRIPTION FOR D-SUB CONNECTOR TROUBLESHOOTING Symptom Check Signal Pin No picture. Check if power switch and computer power switch Red 1 are in the on position. Green 2 Blue 3 Check if the signal cable is correctly connected to GND 4 the video card. GND 5 GND-Red 6 Check if the pins of D subconnector are not bent. GND-Green 7 GND-Blue 8 Check if the computer is in the power- saving mode. +5Vdc 9 GND-H.Sync 10 POWER LED is not Check if power switch is in the on position. GND-V.Sync 11 lit. Bi
