ملخص المحتوى في الصفحة رقم 1
Table of Contents
About This Guide .............................................................................................................................................. 1
National Conventions ...................................................................................................................................... 1
FCC Notice ..................................................................................................................................................
ملخص المحتوى في الصفحة رقم 2
About This Guide This guide describes the monitor's features, setup, and operation. information in this document is subject to change without notice. The sections are as follows: Safety Instructions: lists safety information. Setup: describes the initial setup process. Using the Monitor: gives an overview of how to use the monitor. Drivers: provides driver installation instructions for Windows. Technical Support: provides tips and solutions for common problems. Produ
ملخص المحتوى في الصفحة رقم 3
FCC Notice FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructio
ملخص المحتوى في الصفحة رقم 4
HG Declaration SAFETY: Lamp Disposal LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS. FOR MORE INFORMATION, CONTACT THE ELECTRONIC INDUSTRIES ALLIANCE AT WWW.EIAE.ORG. Precautions WARNING: Use of controls, adjustments, or procedures other than those specified in this documentation may result in exposure to shock, electrical hazards, and/or mechanical hazards. Read and follow these precautions when connecting an
ملخص المحتوى في الصفحة رقم 5
Setup stand and base Please setup or remove the base following below steps. Adjusting Viewing Angle For optimal viewing it is recommended to look at the full face of the monitor, and then adjust the monitor's angle to your own preference. Hold the stand so you do not topple the monitor when you tilt the monitor's angle. You are able to adjust the monitor's angle from 5° to 15 ° . NOTE: Do not press the LCD screen to change the viewing angle. It may cause damage or break
ملخص المحتوى في الصفحة رقم 6
Connecting Cables Cable Connections On Back of Monitor and Computer 1. Power 2. Analog Turn off your computer before performing the procedure below. 1. Connect the power cable to the AC port on the back of the monitor. 2. Connect one end of the 15-pin D-Sub cable to the back of the monitor and connect the other end to the computer's D-Sub port. 3. Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, see
ملخص المحتوى في الصفحة رقم 7
Wall Mounting Preparing to Install an Optional Wall Mounting Arm This monitor can be attached to a wall mounting arm which can be purchased separately. Disconnect power before this procedure. Follow these steps: 1. Remove the stand & base. 2. Follow the manufacturer's instructions to assemble the wall mounting arm. 3. Place the wall mounting arm onto the back of the monitor. Line up the holes of the arm with the holes in the back of the monitor. 4. Insert the 4 screws into the ho
ملخص المحتوى في الصفحة رقم 8
Setting Optimal Resolution The recommended resolution for this monitor is 1600 by 900. To setup the monitor to this resolution, follow the steps below. 1. Click START. 2. Click SETTINGS. 3. Click CONTROL PANEL. 4. Double click DISPLAY. 5. Click SETTINGS. 6. Set the resolution SLIDE-BAR to 1600 by 900 7
ملخص المحتوى في الصفحة رقم 9
External Controls Press the power button to turn the monitor on or off. The other control knobs are located at front panel of the monitor (See Figure Below). By changing these settings, the picture quality can be adjusted to your personal preferences. 1 .Auto / Exit 2 .Eco mode (DCR) / < 3 .4:3 or wide / > 4 .Menu / Enter 5 .Power 8
ملخص المحتوى في الصفحة رقم 10
Menu Illustration Press the MENU-button to activate the OSD window. Press< or > to navigate through the functions. Once the desired function is highlighted, press the MENU-button to activate it. If the function selected has a sub-menu, press or again to navigate through the sub-menu functions. Once the desired function is highlighted, press MENU-button to activate it. Press< or > to change the settings of the selected function. To exit and save, select the exit function. If you
ملخص المحتوى في الصفحة رقم 11
Menu Icon Definition Luminance Adjust Range Description Brightness 0-100 Backlight Adjustment Contrast 0-100 Contrast from Digital-register. Standard Mode Standard Text Mode Text Internet Mode Internet Eco mode Game Mode Game Movie Mode Movie Sports Mode Sports Gamma1 Adjust to Gamma1 Gamma Gamma2 Adjust to Gamma 2 Gamma3 Adjust to Gamma 3 DCR Enable dynamic contrast ratio On Image
ملخص المحتوى في الصفحة رقم 12
Adjust Picture Phase to reduce Phase 0-100 Horizontal-Line noise Adjust the horizontal position of H.Position 0-100 the picture. Adjust the vertical position of V.Position 0-100 the picture. Color Temp. Recall Warm Color Warm 6500K Temperature from EEPROM. Recall Normal Color Normal 7300K Temperature from EEPROM. Recall Cool Color Temperature Cool 9300K from EEPROM. Recall SRGB Color sRGB Temperature from EEPROM. Red Red Gain from Digital-register
ملخص المحتوى في الصفحة رقم 13
Brightness 0-100 Adjust Frame Brightness Contrast 0-100 Adjust Frame Contrast Adjust Frame horizontal H. position Position Position V.position Adjust Frame vertical Position Bright Frame on or off Disable or Enable Bright Frame OSD Setup Adjust the horizontal position of H.Position 0-100 OSD Adjust the vertical position of V.Position 0-100 OSD Timeout 5-120 Adjust the OSD Timeout Adjust the transparence of Transparence 0-100 OSD Language Select the OS
ملخص المحتوى في الصفحة رقم 14
Select timing to turn off the Off Timer 0~24hrs monitor. Show the information of the Information main image and sub-image source Reset Reset yes or no Reset the menu to default Exit Exit Exit the main OSD Notes: 1)If the product has only one signal input, the item of "Input Select" is disabled. 2) If the product screen size is 4:3 or input signal resolution is wide format, the item of "Image Ratio" is disabled. 3) One of DCR, Color Boost, and Picture Bo
ملخص المحتوى في الصفحة رقم 15
LED Indicators Status LED Color Full Power Mode Green or Blue Active-off Mode Orange or red I-Menu software Welcome to use “i-Menu” software by ENVISION. i-Menu makes it easy to adjust your display settings by mouse. 14
ملخص المحتوى في الصفحة رقم 16
Drives Windows 2000 1. Start Windows® 2000 2. Click on the 'Start' button, point to 'Settings', and then click on 'Control Panel'. 3. Double click on the 'Display' Icon. 4. Select the 'Settings' tab then click on 'Advanced...’ 5. Select 'Monitor' - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active. Click on 'Properties' button. Please follow the steps given below. 6. Click on
ملخص المحتوى في الصفحة رقم 17
Windows XP 1. Start Windows® XP 2. Click on the 'Start' button and then click on 'Control Panel'. 3. Select and click on the category 'Printers and Other Hardware' 4. Click on the 'Display' Item. 5. Select the 'Settings' tab then click on the 'Advanced' button. 6. Select 'Monitor' tab - If the 'Properties' button is inactive, it means your monitor is properly configured. Please stop installation. - If the 'Properties' button is active, click on 'Properties' button. Please follow
ملخص المحتوى في الصفحة رقم 18
Technical Support Frequently Asked Questions Problem & Question Possible Solutions Make sure the power button is ON and the Power Cord is properly Power LED Is Not ON connected to a grounded power outlet and to the monitor. In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer & video card. Check with your computer manufacturer. Also check the monitor's video cable and make sure none of No Plug & Play the pins are bent. Make
ملخص المحتوى في الصفحة رقم 19
Product Specifications Model name H2062 Driving system TFT Color LCD Viewable Image Size 508.5mm diagonal Pixel pitch 0.2768mm(H) x0.2768mm(V) LCD Panel Video R, G, B Analog interface Separate Sync. H/V TTL Display Color 16.7M Colors Dot Clock 108Mhz Horizontal scan range 30 kHz - 80 kHz Horizontal scan Size(Maximum) 442.8 mm Vertical scan range 55 Hz - 75 Hz Vertical scan Size(Maximum) 249.1mm Optimal preset resolution 1600 x 900 (60 Hz) Highest preset resolution 1600 x 900
ملخص المحتوى في الصفحة رقم 20
EPA ENERGY STAR ® ENERGY STAR® is a U.S. registered mark. As an ENERGY STAR® Partner, ENVISION International (Europe) GmbH has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Preset Display Modes HORIZONTAL VERTICAL STAND RESOLUTION FREQUENCY(kHZ) FREQUENCY(Hz) VGA 640×480 @60Hz 31.469 59.94 VGA 640×480 @67Hz 35 66.667 VGA 640×480 @72Hz 37.861 72.809 VGA 640×480 @75Hz 37.5 75 Dos-mode 720×400 @70Hz 31.469 70.087 SVGA 800×600 @5
