ملخص المحتوى في الصفحة رقم 1
Back to Contents Page
w17e/W17q LCD Monitor
User’s Guide
• Preface
• Safety and Maintenance Guidelines
• Setup
• Using the Monitor
• Installing Drivers and Using the Auto-Adjustment Feature
• Technical Support FAQs
• Specifications
• LCD Monitor Quality and Pixel Policy
• Agency Regulatory Notices
The only warranties for HP products and services are set forth in the express warranty statements accompanying such
products and services. Nothing herein should be construed as constitut
ملخص المحتوى في الصفحة رقم 2
Back to Contents Page Preface About This Guide • Notational Conventions About This Guide This guide is intended for anyone who uses the w17e / W17q LCD Monitor. It describes the monitor’s features, setup, and operation. The sections are as follows: • Safety and Maintenance Guidelines • Setup • Using the Monitor • Installing Drivers and Using the Auto-Adjustment Feature • Technical Support FAQs • Specifications • LCD Monitor Quality and Pixel Policy • Agency Regulatory Notices No
ملخص المحتوى في الصفحة رقم 3
Back to Contents Page Safety and Maintenance Guidelines Important Safety Information � Safety Precautions � Maintenance Guidelines � Cleaning the Monitor Important Safety Information The power cord is designed for use with your monitor. To use a different cord, use only a power source and connection compatible with this monitor. For information on the correct power cord set to use with your monitor, Power Cord Set Requirements. see WARNING: To reduce the risk of electric shock or damag
ملخص المحتوى في الصفحة رقم 4
Maintenance Guidelines To enhance the performance and extend the life of your monitor: • Do not open your monitor cabinet or attempt to service this product yourself. If your monitor is not operating properly or has been dropped or damaged, contact your Hewlett-Packard authorized dealer, reseller, or service provider. • Adjust only those controls that are described in the operating instructions. • Turn your monitor off when not in use. You can substantially increase the life expectancy of
ملخص المحتوى في الصفحة رقم 5
Back to Contents Page Setup Base and Tilt � Cables � Wall Mounting Arm Base and Tilt Attaching the Base � Removing the Base � Adjusting the Tilt Attaching the Base 1 Set the panel face-down on a flat, protected surface. 2 Align the pedestal slots with the panel tabs and insert (A). 3 Slide the pedestal to the right to lock it into place (B). 4 Lift the panel and lower the pedestal onto the base until the push tab locks. WARNING: Be careful to avoid pinching or scraping fingers when
ملخص المحتوى في الصفحة رقم 6
Removing the Base 1 Push the release tab and raise the pedestal off the base. 2 Set the panel face-down on a flat, protected surface. 3 Slide the pedestal to the left to unlock it from the base (A). 4 Remove the pedestal from the panel (B). WARNING: Be careful to avoid pinching or scraping fingers when attaching the base. CAUTION: To prevent damage, avoid applying pressure to the panel front.
ملخص المحتوى في الصفحة رقم 7
Adjusting the Tilt For optimal viewing, adjust the screen tilt to your own preference, as follows: 1 Face the front of the monitor and hold the stand so that you do not topple the monitor while changing the tilt. 2 Adjust the tilt by moving the monitor’s top edge toward or away from you. CAUTION: To avoid breakage or other damage, do not touch the LCD screen while changing the tilt.
ملخص المحتوى في الصفحة رقم 8
Back to Contents Page Cables Attaching the Cables Attaching the Cables Attach the provided VGA cable to this monitor. Connectors are on the back of the monitor. 1 Turn off your computer. 2 Connect the built-in monitor speakers to the computer, using the audio cable (green connector).
ملخص المحتوى في الصفحة رقم 9
3 Connect one end of the 15-pin D-Sub VGA cable (blue connector) to the back of the monitor and connect the other end to the computer VGA port. 4 Connect one end of the power cord to the back of the monitor and plug the other end into a grounded outlet. 5 Turn on your monitor and computer. If your monitor displays an image, installation is complete. If it does not display an image, see Technical Support FAQs and Using the Monitor.
ملخص المحتوى في الصفحة رقم 10
Back to Contents Page Wall Mounting Arm Preparing to Install a Wall Mounting Arm (Not supplied) � Installing a Wall Mounting Arm Preparing to Install a Wall Mounting Arm (Not supplied) This monitor can be attached to a wall mounting arm that you purchase separately. CAUTION: Before disassembling the monitor, turn off the monitor power, and disconnect all power, video, and audio cables. 1 Disconnect the cables from the monitor. 2 With the panel face-down on a protected surface,
ملخص المحتوى في الصفحة رقم 11
Back to Contents Page Using the Monitor Operating Instructions • External Controls � LED Indicators � Settings � Setting the Optimal Resolution � Adjusting the Volume � Locking the OSD � Adjusting OSD Settings � OSD Menu Operating Instructions Control buttons are located on the front of the panel, as shown in the illustration following. Use the Menu button to adjust the display settings to your personal preferences: • Set up the monitor, attach the cables, and adjust the tilt as desc
ملخص المحتوى في الصفحة رقم 12
External Controls A Auto-configuration / Exit B Volume decrease / Left navigation C Volume increase / Right navigation D Menu / Enter E Power F LED indicator LED Indicators Status LED Color Full Power Mode Green Power Save Mode Amber See Technical Support FAQs for more information.
ملخص المحتوى في الصفحة رقم 13
Back to Contents Page Settings Setting the Optimal Resolution • Adjusting the Volume � Locking the OSD � Adjusting OSD Settings � OSD Menu Setting the Optimal Resolution The recommended resolution for this monitor is 1440 by 900. To configure the monitor to this resolution, complete the setup procedure and make sure that the monitor is connected to the computer. Turn the monitor on and do the following: 1 Click the Windows Start Button , and then click Control Panel. 2 Under Appeara
ملخص المحتوى في الصفحة رقم 14
Adjusting OSD Settings 1 Press the Menu button to activate the OSD menu. 2 Press + or – on the monitor front panel to navigate through the functions. Once the desired function is highlighted, press the Menu button again to activate it. If the selected function has a sub-menu, it will be displayed. Press + or – again to navigate through the sub-menu functions. Once the desired sub-function is highlighted, press the Menu button to activate it. 3 Press + or – to change the settings of the sel
ملخص المحتوى في الصفحة رقم 15
Main Menu Sub-Menu Main Menu Item Icon Sub-Menu Item Icon Description (continued) Image Position H. Position Adjust the horizontal position of the picture V. Position Adjust the vertical position of the picture Color Temp. Warm N/A Recall warm color temperature from EEPROM Cool N/A Recall cool color temperature from EEPROM sRGB N/A Recall sRGB temperature from EEPROM User / Red Red gain from digital-register User / Green Green gain from digital-register User / Blue Blue
ملخص المحتوى في الصفحة رقم 16
Back to Contents Page Installing Drivers and Using the Auto-Adjustment Feature Downloading Drivers and Software � Using the Auto-Adjustment Function Downloading Drivers and Software To download the latest version of drivers and software files from the HP Support Web site: 1 Refer to: http://www.hp.com/support 2 Select your country/region. 3 Select Download Drivers and Software. 4 Enter the model number of your monitor. The software download pages for your monitor will be displayed. 5
ملخص المحتوى في الصفحة رقم 17
Back to Contents Page Technical Support FAQs Technical Support FAQs (Frequently Asked Questions) Technical Support FAQs (Frequently Asked Questions) Problem & Question Possible Solutions Power LED is not on • Make sure the Power button is on and the power cord is properly connected to a grounded power outlet and to the monitor. No Plug & Play • In order for the Plug & Play feature of the monitor to work, you need a Plug & Play compatible computer and video card. Check with your comp
ملخص المحتوى في الصفحة رقم 18
Problem & Question Possible Solutions (continued) Missing one of the primary colors (red, • Inspect the monitor’s video cable and make sure that none of the green, or blue) pins are bent. • Make sure the monitor’s video cable is properly connected to the computer. Screen image is not centered or sized • Adjust horizontal and vertical screen position. properly • The auto-adjustment function may fix this problem. Picture has color defects (white does • Adjust RGB color or select color te
ملخص المحتوى في الصفحة رقم 19
Back to Contents Page Specifications General• LCD Panel (17") � Resolution � Preset Display Modes � Physical Characteristics � Environmental � Power Cord Set Requirements � VGA Connector Pin Assignments � Plug and Play DDC2B Feature All specifications represent the typical specifications provided by HP’s component manufacturers; actual performance may vary either higher or lower. General Model number w17e / W17q LCD Panel (17") Driving system TFT Active Matrix Color LCD Size 431.8
ملخص المحتوى في الصفحة رقم 20
Preset Display Modes Standard Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Dos-mode 720 x 400 31 70 VGA 640 x 480 31 60 VGA 640 x 480 35 67 VGA 640 x 480 38 73 VGA 640 x 480 38 75 SVGA 800 x 600 35 56 SVGA 800 x 600 38 60 SVGA 800 x 600 48 72 SVGA 800 x 600 47 75 SVGA 832 x 624 50 75 XGA 1024 x 768 48 60 XGA 1024 x 768 56 70 XGA 1024 x 768 60 75 SXGA 1152 x 864 68 75 WXGA 1440 x 900 56 60 WXGA 1440 x 900 71 75 Physical Characteristics Connector Types 15-pin Mi
