ملخص المحتوى في الصفحة رقم 1
PDP DISPLAY
quick start guide
P42H-2
ملخص المحتوى في الصفحة رقم 2
Introduction Package Contents Note Please make sure the following items are included with your PDP Display. If any items are missing, contact your dealer. Contact a local dealer to buy optional items. Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the Remove the Styrofoam holding the grooves on package. and vinyl cover. both sides of the package box. Note • After unpacking the package, ma
ملخص المحتوى في الصفحة رقم 3
Introduction PDP Display Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all loca- tions) Cables Power Cord Others Remote Control Batteries (AAA X 2) Ferrite Core for Power Cord (Not available in all loca- tions) Sold separately D-Sub Cable DVI Cable Wall Mount KIT Semi Stand KIT Note • You can only connect one external box. Ferrite Core (Power Cord)
ملخص المحتوى في الصفحة رقم 4
Introduction • The ferrite cores are used to shield the cables from interfer- ence. • When connecting a cable, open the ferrite core and clip it around the cable near the plug. Your PDP Display Front SOURCE button [SOURCE] Switches from PC mode to Video mode. Changing the source is only al- lowed for external devices that are connected to the PDP Display at the time. [PC DVIAV HDMI Component] Enter button [ ] Activates a highlighted menu item. MENU button [MENU] Opens the on-screen menu and exit
ملخص المحتوى في الصفحة رقم 5
Introduction Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your PDP Display OFF when it is not needed or when leaving it unattended for long periods. Remote Control Sensor Aim the remote control towards this spot on the PDP Display. Rear Note For detailed information concerning cable connections, refer to Connecting Cables under Setup. The PDP Display 's configuration a
ملخص المحتوى في الصفحة رقم 6
Introduction RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port RGB/COMPONENT IN (PC Video Con- nection Terminal) Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) DVI IN (PC Video Connection Terminal) Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) DVI / RGB IN (PC/DVI Audio Connection Terminal (Input)) AV / COMPONENT AUDIO IN [L- AUDIO - R] Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the [ L- AUDIO - R ] port of the PDP Displa
ملخص المحتوى في الصفحة رقم 7
Introduction Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustra- tion depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately. Note The location of the Kensington Lock may be different depending on its model. Using the Anti-Th
ملخص المحتوى في الصفحة رقم 8
Introduction POWER OFF Number Buttons DEL button + VOL - MUTE TV/DTV MENU INFO Color Buttons TTX/MIX STILL AUTO S.MODE MDC LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT SRS MagicInfo P.MODE DUAL/MTS PIP SWAP Turns the product On. 1. POWER Turns the product Off. 2. Off 3. Number Buttons Press to change the channel.
ملخص المحتوى في الصفحة رقم 9
Introduction The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV. 4. DEL button 5. + VOL - Adjusts the audio volume. Pauses (mutes) the audio output temporarily. This is dis- 6. MUTE played on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. 7. TV/DTV Selects the TV and DTV mode directly. Opens the on-screen menu and exits from the menu or 8. MENU closes the adjustment menu. Activates a highlighted menu
ملخص المحتوى في الصفحة رقم 10
Introduction 22. GUIDE Electronic Program Guide (EPG) display. Returns to the previous menu. 23. RETURN 24. Up-Down Left-Right but- Moves from one menu item to another horizontally, vertically tons or adjusts selected menu values. Exits from the menu screen. 25. EXIT Selects SRS TruSurround XT mode. 26. SRS 27. MagicInfo MagicInfo Quick Launch Button. 28. P.MODE When you press this button, current picture mode is dis- played on the lower center of the screen. AV / HDMI / TV : P.MODE The PDP D
ملخص المحتوى في الصفحة رقم 11
Introduction Mechanical Layout (P42H-2) Mechanical Layout NETWORK MODEL SIZE
ملخص المحتوى في الصفحة رقم 12
Introduction PDP Display Head NETWORK MODEL SIZE Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation profes- sionals will visit you and install the bracket. • At least 2 persons are needed in order to move the PDP Display. • SAMSUNG is not responsible for any product damage or
ملخص المحتوى في الصفحة رقم 13
Introduction Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length. Wall Bracket Installation • Contact a technician for installing the wall bracket. • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the components and
ملخص المحتوى في الصفحة رقم 14
Introduction A - Captive Screw B - Wall Bracket C - Hinge (Left) D - Hinge (Right) 2. Before drilling into the wall, check if the length between the two locking holes at the back of the product is correct. If the length is too short or long, loosen all or some of the 4screws on the wall bracket to adjust the length. A - Length between the two locking holes 3. Check the installation diagram and mark the drill points on the wall. Use the 5.0 mm bit to drill holes deeper than 35 mm. Fix each anchor
ملخص المحتوى في الصفحة رقم 15
Introduction 1. Remove the 4 screws on the back of the product. 2. Insert the screw B into the plastic hanger. Notice • Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers. • Be careful when installing the product on the bracket as fingers can be caught in the holes. • Make sure the wall bracket is securely fixed to the wall, or the product may not stay in place after installation. 3. Tighten the 4 screws in step 2 (plastic hanger + scre
ملخص المحتوى في الصفحة رقم 16
Introduction A - PDP Display B - Wall Bracket C - Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2. Hold the product at the top in the center and pull it forward (direction of the arrow) to adjust the angle. Note You can adjust the bracket angle between -2° and 15°. Make sure to use the top center, and not the left or the right side of the product to adjust the angle.
ملخص المحتوى في الصفحة رقم 17
Connections Connecting a Computer Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the PDP Display. For detailed information on connecting AV input devices, refer to the contents under
ملخص المحتوى في الصفحة رقم 18
Connections Note • Turn on both your computer and the PDP Display. • The DVI cable is optional. • Contact a local SAMSUNG Electronics Service Center to buy optional items. Connecting to Other devices Using a Power cord with Earth • In the event of failure, the earth lead may cause electric shock. Make sure to wire the earth lead in correctly, before connecting the AC power. When un-wiring the earth lead, make sure to disconnect the AC power in advance. Note AV input devices such as DVD players
ملخص المحتوى في الصفحة رقم 19
Connections Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the AV AUDIO IN [L-AUDIO-R] on the PDP Display. 2. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the PDP Display. 3. Select AV for the Camcorder connection using the Source button on the front of the PDP Display or on the r
ملخص المحتوى في الصفحة رقم 20
Connections Connecting Using a DVI to HDMI Cable Note • Connect the DVI output terminal of a digital output device to the DVI IN terminal of the PDP Display using a DVI cable. • Set the name of DVI input to AV device in Source -> Edit Name Menu. Connecting to an Audio System Note • Connect a set of audio cables between the AUX L, R jacks on the AUDIO SYSTEM and AUDIO OUT [L-AUDIO-R] on PDP Display.
