AOC CT700G دليل المستخدم

ملخص المحتوى في الصفحة رقم 1

CT700G
CT710G
CT720G
CT740G
User’s
Manual
2

ملخص المحتوى في الصفحة رقم 2

FCC Class B Radio Frequency Interference Statement PRECAUTIONS Thank you very much for choosing the AOC Color Monitor. We WARNING: (FOR FCC CERTIFIED MODELS)  Do not use the monitor near water, e.g. near a bathtub, recommend that you take a few minutes to read carefully through washbowl, kitchen sink, laundry tub, swimming pool or in a wet NOTE: This equipment has been tested and found to comply with this brief but comprehensive manual before installing and basement. the limits for a Clas

ملخص المحتوى في الصفحة رقم 3

Plug & Play DDC1/2B Feature TECHNICAL SUPPORT(FAQ) This monitor is equipped with VESA DDC1/2B capabilities Power LED is not on INSTALLATION INSTRUCTIONS according to the VESA DDC STANDARD. It allows the monitor to *Power Cord should be connected SWIVEL BASE inform the host system of its identity and, depending on the level No Plug & Play To attach the swivel base to the monitor, do the following: of DDC used, communicate additional information about its display  Carefully turn the monitor

ملخص المحتوى في الصفحة رقم 4

OPERATING INSTRUCTIONS Figure 1 Installing and Removing the Swivel Base GENERAL INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3). By changing these settings, the picture can be adjusted to your personal preferences.  The power cord should be connected.  Connect the video cable from the monitor to the video card.  To turn the monitor on, press the power switch to ON position. The power indicator will light up.  Your monitor features a unique

ملخص المحتوى في الصفحة رقم 5

HOW TO ADJUST A SETTING CONNECTING CABLES 1. Press the Shuttle Knob Key to make the OSD window appear. See figure 4. 1. Power Cord 4. PC Audio Output 2. Rotate the Shuttle Knob to select the desired function. 2. Signal Cable 5. DC Output See figure 4. 3. VGA Card Adapter 3. Press the Shuttle Knob again to select the function that you want to adjust. 4. Rotate the Shuttle Knob to change the settings of the current EXTERNAL CONTROLS function. 5. When the OSD window is active, it sho

ملخص المحتوى في الصفحة رقم 6

5. V- CENTER Adjust the vertical position of the picture. 6. V- SIZE Adjust the picture’s vertical size. 7. ZOOM Adjust the picture’s horizontal and vertical size simultaneously. 8. PINCUSHION Adjust the pincushion and barrel 9. TRAPEZOID Adjust the picture’s trapezoid distortion. 10. PIN-BALANCE Adjust to compensate the pincushion unbalance. 11. PARALLELOGRAM Adjust the picture to be a rectangle. 12. ROTATION Adjust the picture tilt to horizontal position. 6500°K/9300°K The color temperature fo

ملخص المحتوى في الصفحة رقم 7

Factory Preset Timing Table SPECIFICATION HORIZONTAL VERTICAL CRT 43.2cm(17"), 90º deflection, 29mm neck, STANDARD RESOLUTION FREQUENCY FREQUENCY 0.23mm(H), 0.27mm(D) dot pitch Viewable Image Size 40.6cm (16"), diagonal IBM 720 x 400 31.5kHz 70Hz Video 0.7Vpp, R, G, B Analog VGA 640 x 480 31.5kHz 60Hz Separate Sync. TTL Level H/V-sync. Positive/Negative VESA/85 640 x 480 43.3kHz 85Hz Scanning Frequency: Horizontal 30kHz to 72kHz automatically VESA/85 800 x 600 53.7kHz 85Hz Vertical