ملخص المحتوى في الصفحة رقم 1
USE, INSTALLATION AND MAINTENANCE
INSTRUCTIONS FOR BUILT-IN HOT PLATES
Dear Customer
Thank you for purchasing a Blanco Cooktop.
Before we continue telling you about this cooktop, we cordially invite you to become part of the Blanco family by
subscribing to ongoing information and invitations. Please visit our website where you can subscribe and request
such things as invitations to future cooking classes and gourmet recipes. Go to www.meaappliances.com.au and
fill in the subscription details.
Yo
ملخص المحتوى في الصفحة رقم 2
DESCRIPTION OF THE HOT PLATES Natural U-LPG 1 Ultra rapid gas burner of 11.9 MJ 11.9 MJ 2 Semirapid gas burner of 6.3 MJ 6.3 MJ 3 Auxiliary gas burner of 3.6 MJ 3.6 MJ 4 Cast iron trivet 1 burner 5 Cast iron trivet 2 burner 6 Cast iron trivet 3 burner 7 Burner control knobs Attention: this appliance has been manufactured for domestic use only and is for use by private persons. 2
ملخص المحتوى في الصفحة رقم 3
USE HOW TO USE THE BURNERS 1) BURNERS In order to achieve maximum efficiency with the least A diagram is screen-printed above each knob on the possible gas consumption: front panel. This diagram indicates to which burner - Use adequate pans for each burner (consult the the knob in question corresponds. After having following table and fig. 2). opened the gas mains or gas bottle tap, light the - When the pan comes to the boil, set the knob to the burners as described below: reduced rate position
ملخص المحتوى في الصفحة رقم 4
USE Notes: Use of a gas cooking appliance produces heat and moisture in the room in which it is installed. The room must therefore be well ventilated by keeping the natural air vents clear (fig. 3) and by activating the mechanical aeration device (rangehood or electric fan fig. 4 and fig. 5). Intensive and lengthy use of the appliance may require additional ventilation. This can be achieved by opening a window or by increasing the power of the mechanical exhausting system if installed. Star Triv
ملخص المحتوى في الصفحة رقم 5
CLEANING IMPORTANT: established by the rounded corners, which Always disconnect the appliance from the gas should be set towards the side edge of the hot and electricity mains before carrying out any plate. cleaning operation. - Do not force the taps if they are difficult to open or close. Contact the technical assistance 2) HOT PLATE service for repairs. Periodically wash the hot plate, the cast iron pan - Do not use steam jets for cleaning the cooktop. support, the enamelled burner caps “C” an
ملخص المحتوى في الصفحة رقم 6
INSTALLATION mm above the construction above the top of the TECHNICAL INFORMATION FOR THE burner and no construction shall be within 450 mm INSTALLER above the top of the burner. A minimum depth of 60 This appliance shall be installed only by authorised mm from the top of the work surface must be personnel and in accordance with the manufacturer’s provided for this appliance. installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, 4) FIXING T
ملخص المحتوى في الصفحة رقم 7
INSTALLATION Natural Gas 5) LOCATION AND VENTILATION Natural Gas installations require the connection of a gas Ventilation must be in accordance with regulator at the appliance. This regulator is supplied with AS5601/AG 601 – Gas Installations. the appliance on purchase. In general, the appliance should have adequate ventilation for Assemble the regulator (noting the gas flow direction) and complete combustion of gas, proper flueing and to maintain transition pieces (supplied with the applianc
ملخص المحتوى في الصفحة رقم 8
INSTALLATION a) Data Label 7) ELECTRICAL CONNECTION The Data Label is located on the underside of the The appliance is supplied with a 1800 mm long hotplate. A duplicate Data Label is supplied to adhere flexible supply lead. The point of attachment for this lead is located at in an accessible area next to the hotplate. This the rear and on the underside of the appliance hotplate is suitable for Natural Gas and Universal 380 mm from the right hand side. LPG; ensure that the available gas supply m
ملخص المحتوى في الصفحة رقم 9
ADJUSTMENTS Always disconnect the appliance from the - Insert a small screwdriver “D” into hole “C” (fig. 13) electricity main before making any adjustments. and turn the throttle screw to the right or left until the All seals must be replaced by the technician at burner flame has been adequately regulated to the the end of any adjustments or regulations. “Reduced rate” position. Our burners do not require primary air Check that the flame does not go out when the knob adjustment. is sharply swi
ملخص المحتوى في الصفحة رقم 10
CONVERSIONS 9) U-LPG TO NATURAL GAS 10) NATURAL GAS TO UNIVERSAL CONVERSION PROCEDURE LPG CONVERSION PROCEDURE Appliance models: Gas crystal glass hotplate Appliance models: Gas crystal glass hotplate models: models: BCGC74 4 Burners BCGC74 4 Burners BCGC52 2 Burners BCGC52 2 Burners 1. Remove each burner cap and burner skirt. 1. Remove each burner cap and burner skirt. 2. Remove the U-LPG main injector with a 2. Remove the Natural Gas main injector with a 7 mm/VF tube spanner and replac
ملخص المحتوى في الصفحة رقم 11
CONVERSIONS BURNER ARRANGEMENT ON THE HOT PLATE TABLE BY NORMAL INJECTOR NOMINAL HEAT BURNERS GAS PASS PRESSURE DIAMETER INPUT (MJ/h) (1/100 mm) N° DESCRIPTION (kPa) (1/100 mm) MAX. 85 U-LPG 2.75 95 11.9 1 ULTRA RAPID NATURAL 1.00 155 11.9 85 32 U-LPG 2.75 70 6.3 2 SEMIRAPID 32 NATURAL 1.00 112 6.3 30 U-LPG 2.75 53 3.6 3 AUXILIARY NAT
ملخص المحتوى في الصفحة رقم 12
SERVICING WARNING: Greasing the taps (see fig. 19 - 20) Always disconnect the appliance from the If a tap becomes stiff to operate, it must be electricity and gas mains before proceeding immediately greased in compliance with the with any servicing operation. following instructions: Servicing should be carried out only by - Remove the tap. authorised personnel. - Clean the cone and its housing using a cloth soaked in diluent. 11) COMPONENTS REPLACEMENT - Lightly spread the cone with the relative
ملخص المحتوى في الصفحة رقم 13
SERVICING CABLE TYPES AND SECTIONS TYPE OF TYPE OF SINGLE - PHASE HOT PLATE CABLE POWER SUPPLY 2 Gas hot plate H05 RR - F Section 3 X 0.75 mm ATTENTION!!! If the power supply cable is replaced, the installer should leave the ground wire longer than the phase conductors (fig. 21) and comply with the recommendations given in paragraph 8. FIG. 21 13
ملخص المحتوى في الصفحة رقم 14
TECHNICAL ASSISTANCE AND SPARE PARTS MEA – BLANCO TECHNICAL ASSISTANCE AND SPARE PARTS NEW SOUTH WALES SOUTH AUSTRALIA & NORTHERN TERRITORY Head Office, Sales & Marketing Office Agent and Sales Office 104 Vanessa Street S C Lighting & Electrical Supplies Kingsgrove NSW 2208 47 North Terrace Telephone: 02 9503 2888 Hackney SA 5069 Facsimile: 02 9503 2810 Telephone: 08 8362 4599 Facsimile: 08 8362 4591 NSW Showroom* 40 Ebley Street Service and Spare Parts Bondi Junction N
ملخص المحتوى في الصفحة رقم 15
16
