ملخص المحتوى في الصفحة رقم 1
GE Consumer & Industrial
Appliances
Installation Instructions
Built-In Dishwasher
If you have questions, call 800.GE.CARES (800.432.2737) or visit our website at: www.ge.com
BEFORE YOU BEGIN
IMPORTANT – The dishwasher MUST be installed
to allow for future removal from the enclosure if service is
Read these instructions completely and
required.
carefully.
If you received a damaged dishwasher, you should
immediately contact your dealer or builder.
IMPORTANT – Observe all governing codes and
or
ملخص المحتوى في الصفحة رقم 2
Installation Preparation Side and Top Trim Pieces on some models PARTS SUPPLIED IN INSTALLATION PACKAGE: ■ T Tw wo #8-18 x 5/8" Phillips special head scr o #8-18 x 5/8" Phillips special head screws, to ews, to Drain Hose secure dishwasher to underside of countertop. ■ Junction bo Junction box cov x cover and #10 hex head scr er and #10 hex head screw ew ■ Hose Clamp Hose Clamp Screw Kit Drain Hose Hanger ■ Drain hose (appr Drain hose (appro oximately 78" long) ximately 78" long) 923-02D ■
ملخص المحتوى في الصفحة رقم 3
Installation Preparation PREPARE DISHWASHER ENCLOSURE WARNING To reduce the risk of electric shock, fi re, or injury to persons, the installer must ensure that the dishwasher is completely enclosed at the time of installation. This Wall Area must be Free • The dishwasher must be installed so that drain hose is no of Pipes or 24" wires 34-1/2"1/4" more than 10' in length for proper drainage. Min. Underside of 5" 5" • The dishwasher must be fully enclosed on the top, sides and 4" Count
ملخص المحتوى في الصفحة رقم 4
Installation Preparation PREPARE ELECTRICAL WIRING Alternate WARNING Receptacle FOR PERSONAL SAFETY: Remove house Location fuse or open circuit breaker before 18" beginning installation. Do not use an 1-1/2" Dia. Hole (Max.) Receptacle extension cord or adapter plug with this Location 18" appliance. Area 3" 6" 6" from Cabinet Electrical Requirements 24" • This appliance must be supplied with 120V, 60 Hz., and from Wall connected to an individual properly grounded branch circuit, #282 Fren
ملخص المحتوى في الصفحة رقم 5
Installation Preparation PREPARE HOT WATER LINE • The line may enter from either side, rear or floor within the shaded area shown in Figure F. • The line may pass through the same hole as the electrical cable and drain hose. Or, cut an additional 1-1/2" diameter hole to accommodate the water line. If power cord with plug is used, water line must not pass through power cord hole. 4" 1-1/2" Dia. 4" 5" 5" Hole Shut-off Valve Hot 6" 2" From Cabinet 19" From Wall 2" From Floor Cabinet Face Figure
ملخص المحتوى في الصفحة رقم 6
Dishwasher Installation STEP 3: REMOVE WOOD BASE, INSTALL LEVELING LEGS CA CA CA CA CAUTION UTION UTION UTION UTION Do not remove wood base until you are ready to install the dishwasher. The dishwasher will IMPORTANT – Do not kick off wood base! tip over when the door is opened if base is removed. Damage will occur. • Move the dishwasher close to the installation location and lay 625Dia30 STEP 1: PREPARATION it on its back. • Remove the four leveling legs on the underside of the woo
ملخص المحتوى في الصفحة رقم 7
Dishwasher Installation STEP 7: INSTALL DRAIN HOSE TO STEP 5: INSTALL POWER CORD Skip this step if dishwasher will be permanently connected PUMP OUTLET to the house electrical system. Skip this step if drain hose has been pre-installed. In this step you will need the junction box cover and the In this step you will need the drain hose and clamp set aside in #10 x 1/2" hex head screw from the screw kit set aside in Step 1. Step 1. • Stand dishwasher upright. The power cord and connections
ملخص المحتوى في الصفحة رقم 8
Dishwasher Installation STEP 8: POSITION WATER LINE STEP 10: SLIDE DISHWASHER AND HOUSE WIRING THREE-FOURTHS OF THE WAY • Position water supply line and house wiring on the floor of the INTO CABINET opening to avoid interference with base of dishwasher and components under dishwasher. IMPORTANT – Do not push against front panel with knees. Damage will occur. • Grasp the sides of the front panel and slide dishwasher into the opening a few inches at a time. 5" 5" 4" 4" 4" 6" 6" Water Hou
ملخص المحتوى في الصفحة رقم 9
Dishwasher Installation STEP 12: INSTALL GPF65 SIDE-MOUNT STEP 13: PUSH DISHWASHER INTO BRACKETS FINAL POSITION Skip this step if underside of countertop is wood or • Check the tub insulation blanket, if equipped, to be sure it is wood-like material. smoothly wrapped around the tub. It should not be “bunched • Install side-mount brackets if underside of countertop is up” and it must not interfere with the door springs. If the granite or similar material that will not accept wood screws. in
ملخص المحتوى في الصفحة رقم 10
Dishwasher Installation STEP 14: LEVEL DISHWASHER STEP 15: POSITION DISHWASHER, SECURE TO COUNTERTOP OR CABINET IMPORTANT – Dishwasher must be level for proper In this step you will need the 2 Phillips special head screws dish rack operation, wash performance and door operation. from the screw kit set aside in Step 1. The dishwasher must be leveled left to right and front to back. This assures the dish racks will not roll in or out on their own, The dishwasher must be secured to the counte
ملخص المحتوى في الصفحة رقم 11
Dishwasher Installation • Connect drain line to air gap, waste tee or disposer STEP 16: CONNECT WATER SUPPLY using the previously determined method. Secure hose Connect water supply line to 90° elbow. with a screw type clamp. • Slide compression nut, then ferrule over end of water line. • Insert water line into 90° elbow. Method 1 – Air gap with waste tee or disposer • Slide ferrule against elbow and secure with compression nut. IMPORTANT – Check to be sure that door spring and/or door sp
ملخص المحتوى في الصفحة رقم 12
Dishwasher Installation STEP 18: CONNECT POWER SUPPLY STEP 19: PRETEST CHECK LIST If a power cord with plug is already installed proceed to Review this list after installing your dishwasher to avoid Step 19. charges for a service call that is not covered by your warranty. ■ Check to be sur Check to be sure pow e power is OFF er is OFF.. WARNING If house wiring is not 2-wire with ground, a ■ Open door and r Open door and remov emove all foam and paper packaging. e all foam and paper packagin
ملخص المحتوى في الصفحة رقم 13
Toekick Dishwasher Installation STEP 20: DISHWASHER WET TEST STEP 21: REPLACE TOEKICK ■ T Turn on pow urn on power supply or plug pow er supply or plug power cor er cord into outlet d into outlet, , • Place toekick against the legs of the dishwasher. if equipped. ■ Latch door Latch door.. ■ Push “Rinse Only” pad. Push “Rinse Only” pad. ■ Push S Push Star tart/R t/Reset pad one time. Dishw eset pad one time. Dishwasher should star asher should start t.. ■ Check to be sur Check to be sure th
ملخص المحتوى في الصفحة رقم 14
Notes
ملخص المحتوى في الصفحة رقم 15
Notes 14
ملخص المحتوى في الصفحة رقم 16
SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE GE Consumer & Industrial © 2005 General Electric Company General Electric Company Pub. No. 31-30217 ������������ Louisville, Kentucky 40225 ��� � ��� Dwg. No. 206C1559P157 ND 06G-1871 (8/06) ge.com
