Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION INSTRUCTIONS FOR PART 95-7504
APPLICATIONS
Mazda 3 2004-2009
95-7504
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
• Bonus Display Replacement Pocket
KIT COMPONENTS
• A) Radio Housing • B) Double DIN Brackets • C) Double DIN Trim plate
•D) Display Replacement Pocket • E) Display Retention Brackets
• F) (2) 3/8” #10 Bolts and (2) #10 Nuts • G) (2) PC-7503 Panel Clips
F
C
B
G
A
D
E
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Har
Inhaltszusammenfassung zur Seite Nr. 2
95-7504 TABLE OF CONTENTS Dash Disassembly - Mazda 3 2004-2009 . ... ... .... ... .... ... .... . . . . . . . . 1 Kit Assembly - Display Brackets/Pocket Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - Double DIN Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
LOAD CLOCK SET AM CD FM1/2 TAPE/MD 95-7504 DASH DISASSEMBLY MAZDA 3 2004-2009 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove display trim panel above radio. Tip: Open glove box and start in middle of panel working towards drivers side first because last HOOK connection on far passenger side is a hook. (Figure A) 3 Remove (2) Phillips screws exposed at top of radio then unclip and B remove radio. Note: Display is attached to radio bracke
Inhaltszusammenfassung zur Seite Nr. 4
95-7504 DISPLAY POCKET ASSEMBLY DISPLAY BRACKETS/POCKET ASSEMBLY MAZDA 3 2004-2009 AUTOMATIC CLIMATE CONTROL VEHICLES A 1 Using the (2) 3/8” #10 bolts and (2) #10 nuts attach the display retention brackets to the display unit. 2 Remove the (2) Phillips screws in the sub dash. (Figure A) 3 Secure the display unit into the sub dash using the screws removed in the previous step. MANUAL CLIMATE CONTROL VEHICLES B 1 Using the (2) Phillips screws removed in step 4 of Dash Disassembly secure the displa
Inhaltszusammenfassung zur Seite Nr. 5
95-7504 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Snap the Double DIN brackets to the inside edge of the radio housing. (Figure A) 2 Slide the Double DIN radio into the bracket/radio housing assembly and secure the radio to the assembly using the screws supplied with the radio. Snap the trim plate onto the front of the radio housing. (Figure B) B 3 Attach the (2) PC-7503 panel clips to the rear of the radio housing. (Fi
Inhaltszusammenfassung zur Seite Nr. 6
95-7504 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Snap the Double DIN brackets to the A inside edge of the radio housing. (Figure A) 2 Slide the stacked ISO units into the bracket/radio housing assembly and secure the units to the kit using the screws supplied with the units. Snap the trim plate onto the front of the radio housing. (Figure B) 3 Attach the (2) PC-7503 panel clips to B the rear of the radio housing. (Figur
Inhaltszusammenfassung zur Seite Nr. 7
95-7504 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
Inhaltszusammenfassung zur Seite Nr. 8
FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually tape off ends of any unused wires to prevent electrical short circuit. METRA / EIA WIRING CODE 12V Ignition / Acc. . . . . . . . . . Red Right Front (+) . . . . . . . . . . . . Gray 12V Batt / Memory. . . . . . . . . Yellow Right Front (-). . . . . . .
