Inhaltszusammenfassung zur Seite Nr. 1
User’s Guide
L1972H
Make sure to read the Important Precautions before using this product.
Keep the User's Guide (CD) in an accessible place for future reference.
See the attached label on the unit and show this information to your dealer
when asking for service.
Inhaltszusammenfassung zur Seite Nr. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Inhaltszusammenfassung zur Seite Nr. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Inhaltszusammenfassung zur Seite Nr. 4
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Unfolding the stand base 1. Place the monitor with its front facing downward on a soft cloth. 2. Hold the stand base and lift it up following the sequence as shown in the picture. 3. Pull the stand base down at the same spot shown in the picture, and the stand will be unfolded. 4. Place the monitor upright and adjust the stand base to the des
Inhaltszusammenfassung zur Seite Nr. 5
Connecting the Display Folding the stand base 1. Face the front of the monitor dislpay. Than gently push the monitor backwards, following the sequence shown in the picture below. Tilt range 1. Make sure that the angle of the panel is set for your comfort. Tilt Range : 0˚~30 Ergonomic It is recommended that in order to maintain an ergonomic and comfortable viewing position, the forward tilt angle of the monitor should not exceed 5 degrees A4
Inhaltszusammenfassung zur Seite Nr. 6
Connecting the Display To adjust the height Scope of adjusting the height : maximum 4.02 inches (102 mm) 102 mm A5
Inhaltszusammenfassung zur Seite Nr. 7
Connecting the Display Using the Computer 1. Make sure to turn off the computer and product. Connect the cable as below sketch map 2 form 1 to . A Connect DVI Cable NOTE B Connect Dsub Cable (PC) This is a simplified representation of the rear view. C Connect Dsub Cable (Mac) This rear view represents a general model; your display may differ from the view as shown. Signal Cable Power Cord 1 2 Varies according to model. Wall-outlet type DVI-D(This feature is not available in all countries.) P
Inhaltszusammenfassung zur Seite Nr. 8
Connecting the Display To arrange the cables 1. Insert and screw the cable holder into the hole in the back of the stand until it will not turn any more as shown in the following figure. 2. After connecting the cables neatly, arrange the cables to the Cable Holder as shown in the following figure. Cable Holder A7
Inhaltszusammenfassung zur Seite Nr. 9
Control Panel Functions Front Panel Controls Bottom 6 Control Function At the current display, Use 'ez Zooming' Key, then the display resolution ZOOMING is transferred to the one step low resolution. Use 'ez Zooming' Key one more, the display is back to the original display. Those with poor eyesight such as the elderly, those who have difficulty using computers and children can enlarge text or pictures by adjusting resolution with a single touch. To use this feature, please install forteManager
Inhaltszusammenfassung zur Seite Nr. 10
Control Panel Functions Control Function Use these buttons to select or adjust functions in the - + Buttons On Screen Display. - Button For more information, refer to page A15. ( ) Use this button to make either D-Sub or DVI + Button (SOURCE Hot key) connector active. This feature is used when two computers are connected to the display. The default setting is D-Sub. AUTO/SET Use this button to selection an icon in the On Screen Button Display. AUTO IMAGE ADJUSTMENT When adjus
Inhaltszusammenfassung zur Seite Nr. 11
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the display's image size, position and operating parameters is quick and easy with the On Screen Display Control system(OSD). A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make by using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making any image adjustments. To
Inhaltszusammenfassung zur Seite Nr. 12
On Screen Display (OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A D Reference BRIGHTNESS To adjust the brightness, PICTURE contrast and gamma of the CONTRAST screen GAMMA sRGB To customize the color of COLOR PRESET the screen 6500K 9300K RED GREEN BLUE HORIZONTAL To adjust the position of the POSITION screen VERTICAL CLOCK To improve the clarity and TRACKING stability, sh
Inhaltszusammenfassung zur Seite Nr. 13
On Screen Display (OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Menu Name PICTURE Sub-menus Icons Button Tip MENU : Exit : Adjust (Decrease/Increase) - + SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on th
Inhaltszusammenfassung zur Seite Nr. 14
On Screen Display (OSD) Selection and Adjustment Main menu Sub menu Description PICTURE BRIGHTNESS To adjust the brightness of the screen. PICTURE To adjust the contrast of the screen. CONTRAST GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease - + : Increase SET : Select another sub-menu COLOR COLOR • sRGB: Set the screen color to fit the PRESET SRGB standard color speci
Inhaltszusammenfassung zur Seite Nr. 15
On Screen Display (OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. MENU : Exit : Decrease - SHARPNESS To adjust the clearness of the screen. + : Increase SET : Select another sub-menu To choose the lan
Inhaltszusammenfassung zur Seite Nr. 16
On Screen Display (OSD) Selection and Adjustment The OSD screen will appear when you touch the (-) button on the front of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side. Press the SET button to use the adjusted screen. Main menu Sub men
Inhaltszusammenfassung zur Seite Nr. 17
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power on and the • Adjust the brightness and the contrast. power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving amber? the mouse or pressing any key on the keyboard to bring up the screen. • Try to turn on the PC.
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting Display image is incorrect Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. • Press the AUTO/SET button to automatically On the screen adjust your display image to the ideal setting. background, vertical If the results are unsatisfactory, decrease the bars or stripes are vert
Inhaltszusammenfassung zur Seite Nr. 19
Troubleshooting Display image is incorrect The screen color is • Check if the signal cable is properly connected mono or abnormal. and use a screwdriver to fasten if necessary. • Make sure the video card is properly inserted in the slot. • Set the color setting higher than 24 bits (true color) at Control Panel - Settings. • Check if the screen is set to interlace mode and if The screen blinks. yes, change it to the recommend resolution. Have you installed the display driver? Have you insta
Inhaltszusammenfassung zur Seite Nr. 20
Specifications Display 19 inches (48.26 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating Visible diagonal size : 48.26 cm 0.294 mm pixel pitch Sync Input Horizontal Freq. Analog : 30 - 83 kHz (Automatic) Digital : 30 - 71 kHz (Automatic) Vertical Freq. 56 - 75 Hz (Automatic) Input Form Separate TTL, Positive/Negative SOG (Sync On Green), Digital(HDCP) Video Input Signal Input 15 pin D-Sub Connector DVI - D connector (Dig
