Inhaltszusammenfassung zur Seite Nr. 1
ENGLISH
OWNER’S MANUAL
LCD MONITOR
Please read this manual carefully before operating your set and
retain it for future reference.
LCD MONITOR MODELS
W1943SB W1943TB
W2043SE W2043TE
W2243S W2243T
www.lg.com
Inhaltszusammenfassung zur Seite Nr. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential electrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stan
Inhaltszusammenfassung zur Seite Nr. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Inhaltszusammenfassung zur Seite Nr. 4
Important Precautions On Cleaning Unplug the display before cleaning the face of the display screen. Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display screen because over-spraying may cause electrical shock. When cleaning the product, unplug the power cord and scrub gently with a soft cloth to prevent scratching. Do not clean with a wet cloth or spray water or other liquids directly onto the product. An electric shock may occur. (Do not use chemicals such as benz
Inhaltszusammenfassung zur Seite Nr. 5
Accessories !!! Thank for selecting LGE products !!! Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. User's Guide/Cards Power Cord (Depending on the country) DVI-D Signal Cable 15-pin D-Sub Signal Cable (This feature is not available (To set it up, this signal cable may in all countries.) be attached to this product before shipping out.) IMPORTANT This accessories may look different from those shown here. User must use shield
Inhaltszusammenfassung zur Seite Nr. 6
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices are turned off. Connecting and Disassembling the stand 1. Place the monitor face down on the soft cloth. 2. Assemble the Stand Base into the Stand Body in the correct direction. Stand Body Stand Base 3. Turn the Stand Base Lock through 90˚ to fix the Stand Base to the Stand Body. Base Lock 4. Once assembled, lift the monitor up carefully. 5
Inhaltszusammenfassung zur Seite Nr. 7
Connecting the Display 5. Turn the Stand Base Lock through 90˚ to separate the Stand Base from the Stand Body. If you can't release the Stand Base even the Locking Knob is at a release position, Please push the indicated knob down and retry it. Locking Knob 6. Pull out the Stand Base to remove. IMPORTANT This picture depicts the general model of connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding only the stand base.
Inhaltszusammenfassung zur Seite Nr. 8
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display -After installation, adjust the angle as shown below. 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range : -5˚~15˚ 15 -5 Do not touch or press the screen when adjusting the angle of the monitor. ERGONOMIC It is recommended that in order to maintain an er
Inhaltszusammenfassung zur Seite Nr. 9
Connecting the Display W1943TB/W2043TE/W2243T Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw 1 2 of the signal cable. A Connect D-sub(Analog signal) Cable B Connect DVI-D(Digital signal) Cable NOTE This is a simplified representation of the rear view. This rear view represents a general m
Inhaltszusammenfassung zur Seite Nr. 10
Connecting the Display W1943SB/W2043SE/W2243S Connecting with the PC 1. Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. 2. Connect signal input cable and power cord in order, then tighten the screw 1 2 of the signal cable. A Connect D-sub(Analog signal) Cable NOTE This is a simplified representation of the rear view. This rear view represents a general model; your display may differ from the
Inhaltszusammenfassung zur Seite Nr. 11
Control Panel Functions Front Panel Controls W1943TB/W2043TE/W2243T 1 2 3 4 5 W1943SB/W2043SE/W2243S 1 2 3 4 5 Button Use this button to enter 4:3 IN WIDE, PHOTO EFFECT menus. For more information, refer to page 14. Use this button to enter or exit the On Screen Display. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should app
Inhaltszusammenfassung zur Seite Nr. 12
Control Panel Functions Use these buttons to select or adjust functions in the On Buttons Screen Display. Use this function to select optimal image conditions in accordance with the surrounding environment (Brightness, Image type). For more information, refer to page 15. When two input signals are connected, you can select the input signal (D-SUB/DVI) you want. When only one signal (SOURCE Hot key) is connected, it is automatically detected. The default setting is D-Sub. (Only W1943TB/W2043TE/W
Inhaltszusammenfassung zur Seite Nr. 13
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. To make adjustments in the On Screen Display, follow these steps: Move where Select a Adjust the Exit
Inhaltszusammenfassung zur Seite Nr. 14
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. : Analog Input only * Main menu Sub-menu Description 4:3 IN WIDE To adjust the image size NORMAL PHOTO To adjust the screen color mode EFFECT GAUSSIAN BLUR SEPIA MONOCHROME F-ENGINE MOVIE To select or customize desired INTERNET image settings USER NORMAL DEMO BRIGHTNESS PICTURE To adjust the brightness, CONTRAST contrast and gamma of the GAMMA screen
Inhaltszusammenfassung zur Seite Nr. 15
On Screen Display(OSD) Selection and Adjustment The following OSD screen will appear when you press the button on the front of the monitor. MENU : Exit : Move SET : Select Main menu Description To select the image size of the screen. 4:3 IN WIDE WIDE 4:3 • WIDE : Switch to full screen mode according to input image signal. • 4:3 : Change the input image signal ratio to 4:3. PHOTO To select the color effects of the screen. EFFECT • NORMAL The PhotoEffect function is di
Inhaltszusammenfassung zur Seite Nr. 16
On Screen Display(OSD) Selection and Adjustment The following OSD screen will appear when you press the button on the front of the monitor.This feature lets you easily select the best desired image condition optimized to the environment (ambient illumination, image types etc). Menu Name Icons MENU : Save & Exit Sub-menu Name , : Move F-ENGINE Active state Inactive state When the F-ENGINE is executed, the screen is split to show the effects of the selected function. The act
Inhaltszusammenfassung zur Seite Nr. 17
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. Main Menu MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu : Restart to select sub-menu Button Tip Menu Name Sub- Icons menus NOTE OSD (On Screen Display
Inhaltszusammenfassung zur Seite Nr. 18
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE To adjust the brightness of the screen. BRIGHTNESS To adjust the contrast of the screen. CONTRAST GAMMA Set your own gamma value. : -50 / 0 / 50 On the monitor, high gamma values display whitish images and low gamma values display blackish images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR PRESET Select the screen color. • sRGB: Set the screen color to fit the sRGB standard co
Inhaltszusammenfassung zur Seite Nr. 19
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING HORIZONTAL To move image left and right. To move image up and down. VERTICAL To minimize any vertical bars or CLOCK stripes visible on the screen background. The horizontal screen size will also change. To adjust the focus of the display. PHASE This item allows you to remove any horizontal noise and clear or sharpen the image of characters. MENU : Exit : Decrease To adjust the clearness of the screen. SHARP
Inhaltszusammenfassung zur Seite Nr. 20
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description SETUP W1943SB/W2043SE/W2243S LANGUAGE To choose the language in which the control names are displayed. OSD To adjust position of the OSD window POSITION on the screen. WHITE If the output of the video card is BALANCE different the required specifications, the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video
