Resumen del contenido incluido en la página 1
Empowered by Innovation
– Please Read –
Important DSX Cordless Lite II Telephone Installation Information
DSX Cordless Lite II Telephone Installation Tips
Important
• Only connect the cordless base unit to a DSX-80/160 16ESIU PCB port or a DSX-40 digital
station port. Do not plug the base into an analog port or a DS-2000 16DSTU PCB.
1
• For best results, the base unit should be placed in line-of-site with its handset.
• Cordless telephone range and reception can vary from site to
Resumen del contenido incluido en la página 2
This manual has been developed by NEC Unified Solutions, Inc. It is intended for the use of its customers and service personnel, and should be read in its entirety before attempting to install or program the system. Any comments or suggestions for improving this manual would be appreciated. Forward your remarks to: NEC Unified Solutions, Inc. 4 Forest Parkway Shelton, CT 06484 www.necunifiedsolutions.com Nothing contained in this manual shall be deemed to be, and this manual does not con
Resumen del contenido incluido en la página 3
Table of Contents Table of Contents Chapter 1: Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Programming. . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 4
Table of Contents Hold. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Hotline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Intercom . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Last Number Redial . . . . . . . . . .
Resumen del contenido incluido en la página 5
Introduction Chapter 1: 1 Installation Introduction DSX Cordless Lite II Telephone DSX Cordless Lite II 900 Mhz Cordless Telephone Overview The DSX Cordless Lite II Telephone (P/N 730087) is a 900 Mhz digital narrow band FM cordless telephone that provides mobility, flexibility and convenience for those who spend much of the workday away from their desk. Fully integrated with the DSX sys- tem, the DSX Cordless Lite II Telephone offers many standard features such as Call For- wa
Resumen del contenido incluido en la página 6
The Basics Basic Operation The Basics Basic Operation Using the Basic Features Answering Calls ❥ Outside calls: Ring with 2 short rings followed by a long ring. ❥ Intercom calls: Ring with 1 long ring. ❥ To answer a call: Press TALK or the flashing line key. - If your handset is in the charger, lifting the handset answers the incoming call. Placing Calls ❥ Intercom calls: Press TALK + Dial co-worker’s ex
Resumen del contenido incluido en la página 7
1093092 - 1 The Basics Basic Operation Using Your Cordless Telephone Ring Volume Ringer On when ring is turned off While idle, press to select ring type or vibrate 2-line, 16 While on a call, press character display to change handset receiving volume Voice Mail On if you have Talk Battery a Voice Mail message Ring On/Off Mute 1 Off while idle or Message Waiting. On when While on a call, press to mute battery is low Dial *8 to respond On while on a call
Resumen del contenido incluido en la página 8
Installation Installing the Base Installation Installing the Base Connecting the Base To connect the base to the DSX system (Figure 2: Installing the Base): Be sure to review Guidelines for Placing the Base, Figure 3: Correct Installation Methods, and Figure 4: Incorrect Installation Methods prior to connecting the base unit to the system. 1. Install a modular jack within 6 feet of the base and within 6 feet of an available standard (NEMA 5-1
Resumen del contenido incluido en la página 9
1093092 - 2 625 Modular Jack Installation Installing the Base DSX 16ESIU PCB DSX Digital Keyset Jack YEL BLK WHT-BLU BLU-WHT 1 Station Block RED GRN AC Adaptor Line out Line in (Optional) Line out to DSX Keyset Figure 2: Installing the Base DSX Cordless Lite II Telephone User Guide Chapter 1: Installation ◆ 5
Resumen del contenido incluido en la página 10
80683 - 6 80683 - 7 Installation Installing the Base Correct line-of-site installation, away from devices that cause interference or locations that block signal. Figure 3: Correct Installation Methods Foil backed insulated ceiling Metal studs Too close to another device that emits EMI Too close to other 900 Mhz devices Behind a door that can be closed, tinted windows or one way glass Figure 4: Incorrect Installation Methods 6 ◆ Chapter 1: Installation DSX Cordless Lite II Telephone User Guide
Resumen del contenido incluido en la página 11
Installation Wall-Mounting the Base Wall-Mounting the Base Mounting the Base on the Wall To mount the base on the wall (Figure 5: Mounting the Base on the Wall): 1. Run the base line cord in the wide wire channel as shown, but do not plug it into the base. 2. Run the AC adaptor cord in the narrow wire channel as shown, but do not plug it into the base. 3. Using suitable fasteners, attach the wall-mount bracket to the wall in the desired location. - To make the base easier to remove later on, con
Resumen del contenido incluido en la página 12
Installation Wall-Mounting the Base Mounting the Base to a Wall Plate To mount the base on a standard wall plate (Figure 6: Mounting the Base to a Standard Wall Plate): 1. Snap the base onto the wall-mount bracket. - Make sure the mounting ears fit all the way into their slots and the mounting tabs snap into place. 2. Run a customer-provided short line cord in the wide wire channel as shown and plug it into the base. 3. Run the AC adaptor cord in the narrow wire channel as shown and plug it into
Resumen del contenido incluido en la página 13
80683 - 2 Installation Installing the Battery Installing the Battery Installing the Battery in your Handset To install the battery in your handset (Figure 7: Installing the Handset Battery): 1. Slide the battery cover off of the handset. 2. Insert the battery lead into the battery connector. Be sure to observe the polarity of the connection by lin- ing up the black dot with the black wire. 3. Turn the battery around so it fits into the battery compartment. 4. Slide the battery cover back onto the
Resumen del contenido incluido en la página 14
80683 - 4 Installation Charging the Handset Charging the Handset Installing the Charger and Charging the Handset To connect the AC Adaptor to the charger (Figure 8: Installing the Charger): 1. Run the AC adaptor cord under the strain relief on the back of the charger as shown. 2. Plug the AC adaptor cord into the charger. 3. Plug the AC adaptor into AC outlet. 4. Insert the handset into the charger. The handset must charge 5-8 hours in its charger prior to initial use. - When the handset is corr
Resumen del contenido incluido en la página 15
80683 - 11 80683 - 13 Installation Charging the Handset Wall-Mounting the Charger To wall-mount the charger (Figure 10: Wall-Mounting the Charger): 1. Choose a suitable location for the charger wall-mount bracket within 6 feet of an AC outlet. 2. Install suitable fasteners 1 3/16” apart, leaving the heads out about 1/4”. 3. Run the AC adaptor cord through the notch in the bottom of the wall-mount bracket and up through the rectangular cutout in the bracket. 4. Place the wall-mount bracket on th
Resumen del contenido incluido en la página 16
80683 - 9 80683 - 10 80683 - 8 Installation Using the Belt Clip Using the Belt Clip Installing the Belt Clip To install the belt clip (Figure 11: Installing the Belt Clip): 1. With the open end of the clip facing away from the antenna, snap the belt clip onto the handset. Snap prongs into slots Snap prongs into slots on other side Figure 11: Installing the Belt Clip To remove the belt clip (Figure 12: Removing the Belt Clip): 1. Gently pry the belt clip prongs out of the slots in the handset. Pr
Resumen del contenido incluido en la página 17
Installation Using the Earloop Style Headset with your Cordless Telephone Headset with y Using the Earloop Style our Cordless Telephone Installing Headset P/N 750642 (MX150 Earloop Style) 1 Figure 13: Headset P/N 750642 (MX150 Earloop Style) Ear Cushion Installation To install the ear cushion (Figure 14: Installing the Ear Cushion): 1. Pull the ear cushion over the earpiece. Ear cushion Pull over earpiece Figure 14: Installing the Ear Cushion DSX Cordless Lite II Telephone User Guide Chapter 1:
Resumen del contenido incluido en la página 18
1093092 - 3 Installation Using the Earloop Style Headset with your Cordless Telephone Connecting the Headset and Using the Controls To connect the headset and use the controls (Figure 15: Connecting the Headset): 1. Plug the headset into the Headset Jack on the top of the handset. 2. Clip the Belt/Lapel Clip to your belt or lapel to secure the headset cord. Belt/lapel clip Figure 15: Connecting the Headset 14 ◆ Chapter 1: Installation DSX Cordless Lite II Telephone User Guide
Resumen del contenido incluido en la página 19
80683 - 19 Installation Using the Headband Style Headset with your Cordless Telephone Using the Headband Style Headset with your Cordless Telephone Installing Headset P/N 750637 (M175 Headband Style) 1 Figure 16: Headset P/N 750637 (M175 Headband Style) Optional Earloop Installation To install the optional earloop: 1. Snap the head band out of the ear piece. Figure 17: Installing the Optional Earloop DSX Cordless Lite II Telephone User Guide Chapter 1: Installation ◆ 15
Resumen del contenido incluido en la página 20
80683 - 21 80683 - 20 Installation Using the Headband Style Headset with your Cordless Telephone 2. Remove the ear cushion. Figure 18: Removing the Ear Cushion 3. Snap on the earloop ring. (Make sure the earloop ring lies flat against the microphone boom as shown.) Figure 19: Snapping on the Earloop Ring 4. Insert the earloop into the earloop ring. (Installation for the right ear is shown. For the left ear, insert the earloop from underneath the earloop ring.) Figure 20: Inserting the Earloop i
