Resumen del contenido incluido en la página 1
Preparation Basics Caller ID/Call waiting
Additional Information
SG-1801.qxd 4/19/1 9:12 AM Page 1
,
OWNER S MANUAL
2.4GHz DIGITAL SPREAD SPECTRUM CORDLESS TELEPHONE
-
SG 1801
The FIRST thing to do after unpacking your new
cordless telephone is:
CHARGE THE BATTERY !
Please read and follow the few instructions on
PAGE 2
BEFORE YOU DO ANYTHING ELSE.
Resumen del contenido incluido en la página 2
SG-1801.qxd 4/19/1 9:12 AM Page 2 GETTING STARTED: DO THIS FIRST! FIRST, CHARGE THE HANDSET BATTERY! • Set your new phone in an out-of-the-way place near a power outlet where it will not be disturbed. • Plug the AC adaptor into the wall outlet. • Plug the AC adaptor cord into the power jack on the base unit. • Take the cover off the handset battery compartment; plug the battery connector into the receptacle inside the battery compartment and replace the cover. The connector only goes in one w
Resumen del contenido incluido en la página 3
Preparation SG-1801.qxd 4/19/1 9:12 AM Page 3 INTRODUCTION FEATURES Toshiba America Consumer Products, Inc., takes pride in presenting the new 2.4 GHz digital spread spectrum cordless telephone. The Toshiba cordless telephone features a 16-digit x 3-line dot matrix liquid crystal display (LCD) for caller ID on Call Waiting and speed-dial programming and calling. The sleek new design provides face-up battery charging even when wall mounted. Other features are summarized below. • 2.4 GHz Digital
Resumen del contenido incluido en la página 4
SG-1801.qxd 4/19/1 9:12 AM Page 4 TABLE OF CONTENTS Preparation INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 IMPORTANT SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . .6 LOCATION OF CONTROLS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 Handset . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 5
SG-1801.qxd 4/19/1 9:12 AM Page 5 TABLE OF CONTENTS Steps for entering names and special characters . . . . . . . . . . . . . . .24 If you make a mistake while entering a name . . . . . . . . . . . . . . . . . .25 Dialing a stored number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 Editing and deleting stored numbers . . . . . . . . . . . . . . . . . . . . . . . .26 Caller ID/Call waiting CALLER ID/CALL WAITING . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 6
SG-1801.qxd 4/19/1 9:12 AM Page 6 IMPORTANT SAFETY INSTRUCTIONS When using your telephone equipment, 9 Never push objects of any kind into this product through cabinet slots as basic safety precautions should always they may touch dangerous voltage be followed to reduce the risk of fire, points or short out parts that could electric shock and injury. result in a risk of fire or electric shock. 1 Read and understand all instructions. Never spill liquid of any kind on the 2 Follow all warnings a
Resumen del contenido incluido en la página 7
Preparation SG-1801.qxd 4/19/1 9:12 AM Page 7 IMPORTANT SAFETY INSTRUCTIONS TM The RBRC Seal TM The RBRC Seal on the (easily removable) nickel-cadmium battery (contained in our product) indicates that Toshiba America Consumer Products, Inc. (TACP) is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, TM when taken out of service within the United States. The RBRC program provides a convenient alternative to placing used ni
Resumen del contenido incluido en la página 8
SG-1801.qxd 4/19/1 9:12 AM Page 8 LOCATION OF CONTROLS HANDSET Antenna VOL (VOLUME/RINGER) button Headset jack (Up arrow button) VOL (VOLUME/RINGER) button (Down arrow button) (page 19) MEM (Memory) button (page 22) CID (Caller ID) button (page 28 to 32) TALK button (page 18) CID L.D./1 button (page 30) FLASH button (page 32) L.D. LOCAL button (page 30) LOCAL/3 TONE/ (TONE) button (page 20) ( ) button (Left arrow button) # ( ) button (Right arrow button) (page 22 to 26) TONE (page 22 to
Resumen del contenido incluido en la página 9
Preparation Preparation SG-1801.qxd 4/19/1 9:12 AM Page 9 LOCATION OF CONTROLS BASE UNIT DC IN 9V jack (page 10) LINE modular jack (page 10) Tone/Pulse switch (page 14) Hook IN USE/CHARGE LED PAGE button (page 21) Antenna Charging contacts For purchase of accessories, please call 1-877-644-7373. Owner’s manual Part # RC009816 Quick Reference Guide Rechargeable Battery Pack Part # RC009817 Toshiba TRB-1981 Part # RC009814 9
Resumen del contenido incluido en la página 10
SG-1801.qxd 4/19/1 9:12 AM Page 10 INSTALLATION SETTING UP THE BASE UNIT (DESK TOP MOUNTING) For setting up the base unit follow the instructions below. Snap the bracket’s tab into the notches on the base. Fasten the AC adaptor cord to prevent it from being disconnected. Raise the antenna to vertical position. Single-Line Telephone Jack Telephone Line Cord (RJ11C) Power Outlet (AC 120 V, 60 Hz) AC Adaptor • Plug the AC adaptor firmly into the base unit and the AC 120V outlet. • USE ONLY WITH
Resumen del contenido incluido en la página 11
Preparation Preparation SG-1801.qxd 4/19/1 9:12 AM Page 11 INSTALLATION SETTING UP THE BASE UNIT (WALL MOUNTING) MOUNTING ON A STANDARD WALL PLATE: Insert the bracket’s tabs into the base’s lower tab slots, then press down on the top of the bracket to snap it into the clip slots. Flip the hook tab over Raise the antenna. so the tab holds the handset. Single-Line Telephone Jack (RJ11C) Power Outlet (AC 120 V, 60 Hz) • Route the cords through the guides. AC Adaptor • Place the base unit on the p
Resumen del contenido incluido en la página 12
SG-1801.qxd 4/19/1 9:12 AM Page 12 INSTALLATION CHARGING THE BATTERY PACK It is important to charge the battery for 12-16 hours continuously without any interruption before you use the handset for the first time. Black Red 1 Remove the battery cover on the back of the handset by sliding it down. 2 Plug the battery pack cord into the connector with the correct polarity. (black and red wires). 3 Place the battery pack in the battery compartment. 4 Put the battery cover back by sliding until it
Resumen del contenido incluido en la página 13
Preparation Preparation SG-1801.qxd 4/19/1 9:12 AM Page 13 INSTALLATION After the battery pack is fully charged; Operation Approx. battery life While in use (Talk mode) up to 6 hours While not in use (Standby mode) up to 10 days When "Low Battery" blinks on the LCD, all handset buttons except TALK are disabled and the battery needs to be charged. If this occurs during a call, you hear short beeps. Finish the call as soon as possible and place the handset on the base unit. Low Battery NOTES: •
Resumen del contenido incluido en la página 14
SG-1801.qxd 4/19/1 9:12 AM Page 14 INSTALLATION Before using the Handset, make sure to read the following instructions. VOL () VOL () FUNCTION SELECT/CHANNEL SETTING THE TONE/PULSE SWITCH Set the TONE/PULSE switch to TONE. Place a call. If the call does not connect with the TONE setting, set the TONE/PULSE switch to PULSE. TONE/PULSE switch 14 Preparation
Resumen del contenido incluido en la página 15
Preparation Preparation SG-1801.qxd 4/19/1 9:12 AM Page 15 INSTALLATION SETTING OR CANCELING THE AUTO TALK FUNCTION If the handset is placed on the base unit, you can answer a call by lifting the handset from the base unit (Auto Talk). If the handset is not on the base unit, you can answer a call by pressing any one of the buttons (Any-key Answer function). When the Auto Talk function is set to ON, the Any-key Answer function is also set to ON. When the Auto Talk function is set to OFF, you c
Resumen del contenido incluido en la página 16
SG-1801.qxd 4/19/1 9:12 AM Page 16 INSTALLATION SETTING THE AREA CODE It is necessary to program your area code so that local calls will be displayed properly on caller ID. 1s sAuto Talk:Off 2 CIDCW :On 1Press . FUNCTION 3 Area Code: 1 Auto Talk:Off 2 CIDCW :On 3 2 Press or to move the pointer to Area 3s sArea Code: Code. 1 Auto Talk:Off 2 CIDCW :On SELECT/CHANNEL 3Press . 3 Area Code:615 Enter your 3-digit area code. For example, enter “615.” If you enter a wrong number, press DELETE . 1
Resumen del contenido incluido en la página 17
Preparation SG-1801.qxd 4/19/1 9:12 AM Page 17 INSTALLATION USING THE HEADSET AND BELT CLIP (OPTION) For purchase of an optional accessory, please call 1-877-644-7373. HEADSET You can use an optional headset (part#: RC 008260) that has a 3/32- inch (2.5mm) plug. To connect the headset, open the rubber cover on the left side of the handset, then insert the headset's plug into the jack. With a headset connected, you can make or answer calls as usual using the keys on the handset. When you finish
Resumen del contenido incluido en la página 18
SG-1801.qxd 4/20/1 12:47 PM Page 18 BASIC OPERATION Before using the Handset, make sure to read the following instructions. VOL() FLASH TALK VOL() TONE/ / / DELETE RDL/P MAKING A CALL Handset On The Base Handset Off The Base TALK 1) Pick up the handset. 1) Press . TALK 2) Press . 2) Listen for the dial tone. 3) Listen for the dial tone. 3) Dial the number. 4) Dial the number. OR TALK OR Dial the number, then press . 1) Pick up the handset. TALK 2) Dial the number, then press . TALK To hang up:
Resumen del contenido incluido en la página 19
Basics SG-1801.qxd 4/19/1 9:12 AM Page 19 BASIC OPERATION 3-NUMBER REDIAL You can redial any of the last three numbers dialed from the handset: RDL/P 1 Press in standby mode. The last dialed number (Redial 1) appears. RDL/P Each time you press , the LCD displays one of the three last dialed numbers (Redial 1 to Redial 3). 2 After the desired number has been selected, press TALK . The call will be connected. NOTES: • The handset redials only up to 32 digits even for a number that exceeds this l
Resumen del contenido incluido en la página 20
SG-1801.qxd 4/19/1 9:12 AM Page 20 BASIC OPERATION TONE/PAUSE To Do this TONE/ To temporarily switch to tone dial Press . The following numbers will (When the base is set to pulse mode), be sent as tone dialing. see page 14. To enter a pause within the dialing sequence RDL/P Press . “P” appears in the display which represents a pause. PAUSE EXAMPLE : To make a call “0 12345678” with tone dialing in 0 2 3 4 5 6 TONE/ 1 pulse mode, press RDL/P 7 8 . INTERFERENCE OR STATIC If you hear noise durin
