Resumen del contenido incluido en la página 1
Installation
Instructions
RCWL330A (51459SL)
P4 Premium Portable Plus Wireless Chime and Push
69-2148EFS-01
69-2148EFS_A.indd 1 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 2
Installation Instructions Contents Checking pack contents .........................................................................................................................1 Safety .......................................................................................................................................................2 Quick start ................................................................................................................................................2 O
Resumen del contenido incluido en la página 3
RCWL330A Premium Portable Plus Wirefree Chime with Push Thank you for choosing this Honeywell product. Please use the following instruc- tions to ensure correct installation and use. Keep these notes in a safe place for future reference. Checking Pack Contents Unpack your chime kit and identify the You will need: following parts: • A Phillips-head screwdriver • Chime • A small flat-bladed screwdriver • Chime bracket • A 1/4-in. (6 mm) masonry drill • Bell push • 4 LR14 “C” alkaline batteries •
Resumen del contenido incluido en la página 4
Installation Instructions Safety Before proceeding with the installation, please note the following safety warnings: • Always follow the manufacturer’s advice when using power tools and wear suitable protective equipment (e.g. safety goggles) when drilling holes, etc. • Before drilling holes in walls, check for hidden electricity cables and water pipes. The use of a cable/pipe locator is advisable if in doubt. Quick Start The bell push supplied with this kit is pre-programmed to operate with t
Resumen del contenido incluido en la página 5
RCWL330A Open the Bell Push Insert a flat-bladed screwdriver into the slot A, at the base of the push. Carefully lever the cover and base apart (Fig. 1). A M27269 Fig. 1 3 69-2148EFS—01 69-2148EFS_A.indd 3 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 6
CR2032 + Installation Instructions Install the Bell Push Battery Insert the CR2032 coin cell. Ensure the face marked “+” is facing up (Fig. 2). CR2032 + Fig. 2 M27153 Install the Chime Batteries To remove the chime battery cover, press at point C and slide the cover back, then lift off. Insert 4 LR14 “C” alkaline batteries (not supplied). Observe polarity as marked inside the battery com- partment (Fig. 3). C Fig. 3 M27270 69-2148EFS—01 4 69-2148EFS_A.indd 4 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 7
RCWL330A Switch Positions Mute with flash on To keep the flash on and turn the sound off, set switch (D) to posi- tion 1. Flash off with sound on 1 2 3 To turn the blue flashing light off, set switch (D) to position 3. M27286 D Fig. 4 Normal operation For normal operation (sound and flashing light on), set switch (D) to position 2. 69-2148EFS—01 69-2148EFS_A.indd 5 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 8
1 2 3 5 6 Installation Instructions Sliding Window Release the catch (E) and slide open the window. Shown with number icon strips. Fig. 5 M27271 E 69-2148EFS—01 6 69-2148EFS_A.indd 6 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 9
1 2 3 5 6 RCWL330A Volume Control The volume control is behind the sliding window on the front of the chime. Initially, set the control to mid-point. After you have tested your system, adjust to the desired volume. VOLUME CONTROL Fig. 6 M27272 69-2148EFS—01 69-2148EFS_A.indd 7 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 10
Installation Instructions Use of Icons In addition to the chime sounds, your chime has a visual indication to show which device has activated it. An icon will illuminate when the chime is activated by a bell push or another compatible device. The chime supports six icons: MAIN BACK ALERT INTRUDER TELEPHONE PAGER/ DOOR DOOR SYMBOL KEY FOB M27289 69-2148EFS—01 8 69-2148EFS_A.indd 8 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 11
RCWL330A Use of Icons The “Main door” and “Back door” icons are usually used for bell pushes. The other icons are intended for use with other compatible devices, such as wireless motion detectors and telephone ring detectors (check availability). Icons numbered 1 to 6 are also included. The icons are self-adhesive, supplied in strips of 3. They can be changed, if required, by opening the sliding window of the chime and gently peeling off the strips. If desired, the strips can be cut into in
Resumen del contenido incluido en la página 12
Installation Instructions Programming Procedure Learn procedure Unlearn procedure To enable your chime to learn the identity If you want to remove a push from the of your bell push: chime’s memory: • Press the l button and keep it • Press the l button and keep it pressed. Each Icon will light in pressed. Each Icon will light in turn. turn. When the Icon you want is lit, When the Icon associated with the release the button. push to be unlearned is lit, release the button. • While the Icon yo
Resumen del contenido incluido en la página 13
RCWL330A Changing the Tune Operate the push. While the Icon is flashing, press the button. Press the button again and the tune will change. Repeat until the tune you want plays. Recall Function A short push of the l button will flash the Icon that was last in use. Chime Sounds To hear the chime sounds without operating the bell push, press the button. Press the button again and the tune will change. 11 69-2148EFS—01 69-2148EFS_A.indd 11 3/20/2008 9:34:24 AM
Resumen del contenido incluido en la página 14
Installation Instructions Mount the Bell Push Mount using either the double-sided adhesive pad, or the screws pro- vided (see Fig 7). TOP Test your push before mounting. Avoid mounting to metal structures. M27155 Fig. 7 69-2148EFS—01 12 69-2148EFS_A.indd 12 3/20/2008 9:34:25 AM
Resumen del contenido incluido en la página 15
RCWL330A Chime Position The chime can be free-standing or wall-mounted using the wall bracket provided. If wall mounting is preferred, screw the bracket to the wall (see Fig 8). The chime hooks onto the wall bracket as shown. Fig. 8 M27318 13 69-2148EFS—01 69-2148EFS_A.indd 13 3/20/2008 9:34:25 AM
Resumen del contenido incluido en la página 16
Installation Instructions Troubleshooting A “beep” sound is heard in learn mode… • The push you are programming has already been learned by the chime. • If you want to change the icon associated with the push, use the un-learn procedure, then program the push again. Two “beep” sounds are heard after the normal chime sound… • This indicates a low battery in the bell push that activated the chime. Install a new battery, type CR2032. When the bell push is operated, the amber confidence light doe
Resumen del contenido incluido en la página 17
RCWL330A Troubleshooting The chime does not sound… • Check the chime switch position. • Check that the volume control is not at the minimum setting. The flashing light does not work… • Check the chime switch position. Range is reduced… • Metal structures, including door frames, can reduce the range of the product. Avoid mounting the push or chime on or near metal structures. • Other equipment can cause radio interference that affects your chime. • Walls and ceilings will reduce the range. • Wea
Resumen del contenido incluido en la página 18
Installation Instructions Specifications Specification Chime Bell Push Operating Temperature 32°F to 104°F 14°F to 104°F 0°C to +40°C -10°C to +40°C Range (open field) 450 ft (140 m) RF Frequency 916.8MHz 916.8MHz Sound Level (typical) 90dBA @ 3 ft (1m) RF Power <1mW Battery Type LR14 “C” size CR2032 Battery Life 12 months 18 months (5 activations/day) Rain Proof Pass UL rain test Power Adaptor 6V DC (Not included) 69-2148EFS—01 16 69-2148EFS_A.indd 16 3/20/2008 9:34:25 AM
Resumen del contenido incluido en la página 19
RCWL330A Disposal & Recycling Batteries and waste electrical products should not be disposed of with household waste. Please recycle where these facilities exist. Check with your local authority or retailer for recycling advice. Declaration Honeywell hereby declares that this product complies with Part 15 of the FCC rules and Industrial Canada standards. This device operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device mu
Resumen del contenido incluido en la página 20
Honeywell International Inc. ACS, Environmental and Combustion Controls 1985 Douglas Drive, Golden Valley, MN 55422 www.honeywell.com Printed in U.S.A. on recycled paper containing at least 10% post-consumer paper fibers. ® U.S. Registered Trademark. © 2008 Honeywell International Inc. 69-2148EFS—01 M.S. 03-08 69-2148EFS_A.indd 18 3/20/2008 9:34:25 AM
