Resumen del contenido incluido en la página 7
INTRODUCTION INTRODUCTION Welcome to Moyer Diebel... and thank you for allowing us to take care of your dishwashing needs. This manual covers the door-type dishwasher, Models MH-60, MH-6N, MH-6L. Your machine was completely assembled, inspected, and thoroughly tested at our factory before it was shipped to your installation site. This manual contains: • Installation Instructions • Operation and Cleaning Instructions • Troubleshooting Guide • Basic Service Information • Replacement Parts Lists •
Resumen del contenido incluido en la página 8
GENERAL Model Numbers MH-60, MH-6N, MH-6L The MH-60 model is a high temperature (180°F/82°C rinse) sanitizing model with booster. The MH-6N model is a high temperature (180°F/82°C rinse) sanitizing model without booster. The MH-6L is a low temperature (Min. 120°F/ 49°C-140°F/60°C Optimum) sanitizing model for use with a sodium hypochlorite (Chlorine) based sanitizer at a minimum concentration of 50 PPM in the final rinse. Standard Equipment includes: MH-60, MH-6N, MH-6L • Automatic tank fill • C
Resumen del contenido incluido en la página 9
GENERAL Electrical Power Requirements Model Voltage Booster Rise Machine Power Requirement (MH-60 Only) Full Load Amps (125% Service Factor) MH-6N/MH-6L 115/60/1 — 48 Amps 60 Amps MH-6N/MH-6L 208/60/1 — 23 Amps 29 Amps MH-6N/MH-6L 220/60/1 — 23 Amps 29 Amps MH-6N/MH-6L 230/60/1 — 23 Amps 29 Amps MH-6N/MH-6L 240/60/1 — 24 Amps 30 Amps MH-6N/MH-6L 208/60/3 — 12 Amps 15 Amps MH-6N/MH-6L 220/60/3 — 13 Amps 16 Amps MH-6N/MH-6L 230/60/3 — 13 Amps 16 Amps MH-6N/MH-6L 240/60/3 — 13 Amps 16 Amps MH-6N/MH
Resumen del contenido incluido en la página 10
INSTALLATION INSTALLATION Unpack the dishwasher CAUTION: ! Care should be taken when lifting the machine to prevent damage. NOTE: The installation of your machine must meet all applicable health and safety codes. 1. Immediately after unpacking the machine, inspect for any shipping damage. If damage is found, save the packing material and contact the carrier immediately. 2. Remove the dishwasher from the skid. Move the machine to its permanent location. NOTE: Refer to: To change from Straight-t
Resumen del contenido incluido en la página 11
WALL 5-1/4"[133mm] MIN. INSTALLATION To Change from Straight-through Operation to Corner Operation The dishwasher is shipped from the factory for straight-through operation. The following instructions explain how to change the dishwasher for corner operation. Refer to Fig. 2 1. Place the dishwasher so that operator controls are readily accessible. 2. Minimum clearance from any wall is 5-1/4" (133mm). WALL 5-1/4"[133mm] MIN. FRONT POWER ON SWITCH POWER ON Note: SWITCH Power switch is FRONT read
Resumen del contenido incluido en la página 12
INSTALLATION INSTALLATION (Cont.) Electrical Connections WARNING: ! Electrical and grounding connections must comply with all applicable Electrical Codes. WARNING: ! When working on the dishwasher, discon- nect the electric service and place a tag at the disconnect switch to indicate work is being done on that circuit. 1. A qualified electrician must compare the electrical power supply with the machine electrical specifications before connecting to the incoming service through a fused disconnect
Resumen del contenido incluido en la página 13
INSTALLATION Electrical Connections (Cont.) Refer to Fig. 5 3. Remove (2) lower screws from the front panel of the machine to expose the electri- cal controls. Loosen (1) screw on the control panel support post. Slide the support post up to disengage the post from the machine base. Swing the hinged control panel forward. Figure 5 Hinged Control Panel Refer to Fig. 6 4. Three phase or single phase incoming power wiring connections are made at the bottom of the machine’s main terminal block. The m
Resumen del contenido incluido en la página 14
INSTALLATION INSTALLATION (Cont.) Plumbing Connections NOTE: Plumbing connections must comply with all applicable sanitary and plumbing codes. Water Connections 1. All MH series dishwashers require a single, hot water supply. The hot water connection to all MH series dishwashers is 3/4" NPT. The connection is made from underneath the dishwasher. Figure 7 Hot Water Connection (MH-60 Only) The following minimum water 3/4" NPT temperatures are recommended: MH-60 with built-in 40° rise electric boo
Resumen del contenido incluido en la página 15
INSTALLATION Water Connections (Cont.) 2. A manual shut-off valve for steam and water (supplied by others) should be installed in the supply line to allow for servicing of the machine. The shut-off valve should be the same size or larger than the supply line. 3. Install a 3/4” pressure reducing valve, (PRV), in the water supply line if flow pressure exceeds 20-22 PSI/138-151.8 kPa. A PRV is standard equipment on Model MH-60. A PRV is not standard equipment on Models MH-6N, MH-6L. Drain Connect
Resumen del contenido incluido en la página 16
INSTALLATION INSTALLATION (Cont.) Chemical Connections NOTE: Consult a qualified chemical supplier for your chemical needs. Refer to Fig. 10 1. A chemical signal terminal block is supplied for chemical dispensing equipment. 2. The terminal block is located below the cycle timer on the left side of the hinged control panel. Figure 10 Chemical Dispenser Signal Terminal Block Refer to Fig. 11 Detergent Signal Connection Point 1 Amp Max Load/230VAC 3. The detergent signal is limited to a maximum l
Resumen del contenido incluido en la página 17
INSTALLATION Chemical Connections (Cont.) Refer to Fig. 12 5. A 1/2" NPT detergent probe injection point is provided at the rear of the dishwasher. 6. Detergent may be added manually if your dishwasher is not equipped with dispensing equipment. Consult your chemical supplier for recommended amounts. Figure 12 Refer to Fig. 13 Detergent Probe Injection Point 1/2" NPT 7. A 1/8" NPT rinse aid injection point is (Wash Tank Rear) provided in the final rinse manifold. Use a liquid rinse aid. The mani
Resumen del contenido incluido en la página 18
INITIAL START-UP INITIAL START-UP Complete the installation After plumbing and electrical connections are made, follow the steps below to complete the installation of your dishwasher. 1. Remove the white protective covering from the exterior of the machine. 2. Remove any foreign material from inside the machine. 3. Make sure dishwasher power switch is off. 4. Turn main water supply on. 5. Turn main power on at the main power service disconnect switch. 1 Install the Scrap Screens and Drain-Overfl
Resumen del contenido incluido en la página 19
INITIAL START-UP INITIAL START-UP (Cont.) 3 THE POWER SWITCH IS ON DURING INITIAL FILL. Make sure the doors are fully closed. Push the On/Off power switch to the UP position. THE DISHWASHER FILLS AUTOMATICALLY. 4 Note that the power indicator light is illuminated. 5 Check Wash Water Temperature The wash tank and booster tank heaters will begin to heat the water in the dishwasher. Wait approximately 10 minutes for the wash tank water to reach operating temperature. The temperature should be a min
Resumen del contenido incluido en la página 20
INITIAL START-UP INITIAL START-UP (Cont.) 6 Fully close the dishwasher doors. The dishwasher will begin the automatic cycle. Opening the doors anytime during the cycle will stop the dishwasher. Closing the doors will resume the automatic cycle where it left off. The cycle times are listed below: Wash = 45 seconds Dwell = 1 seconds Final rinse = 14 seconds 7 Note that the in cycle light is lit during the automatic dishwasher cycle. 18
Resumen del contenido incluido en la página 1
Simply Engineered Better
Technical Manual
Door-Type
Dishwasher
Model
MH-60M2
High Temperature
with Built-in Booster
MH-6NM2
High Temperature
MH-6LM2
Low Temperature
Machine Serial No.
Manual P/N 0509506
October, 1996
P. O. Box 4183 2674 N. Service Road
Winston-Salem, North Carolina 27115-4149
Jordan Station, Ontario, Canada LOR 1SO
336/661-1992 Fax: 336/661-1660 905/562-4195 Fax: 905/562-4618
Moyer Diebel
Resumen del contenido incluido en la página 2
Complete the information below so it will be available for quick reference. Model Number Serial Number Voltage and Phase Moyer Diebel Parts Distributor Phone (if applicable) Moyer Diebel Service Agency Phone Moyer Diebel Service: Moyer Diebel, US Phone: 1(336) 661-1992 1(800) 228-8350 Fax: 1(336) 661-1660 Note: When calling to order parts, be sure to have the model number, serial number, voltage and phase of your machine, along with your customer account number. Machine Data Plate with Machine M
Resumen del contenido incluido en la página 3
REVISONS Revision History Revision Revised Serial Number Comments Date Pages Effectivity 10/16/96 All 14165 Issue of manual and replacement parts lists 1
Resumen del contenido incluido en la página 4
CONTENTS CONTENTS LIMITED WARRANTY ............................................................................................................... 4 INTRODUCTION ......................................................................................................................... 5 Model Number ....................................................................................................................6 Standard Equipment ................................................................
Resumen del contenido incluido en la página 5
CONTENTS LIST OF FIGURES (cont.) Figure 9 – Drain Hose Connection ............................................................................................. 13 Figure 10 – Chemical Dispenser Signal Terminal Block ............................................................. 14 Figure 11 – Chemical Signal Connection Points ......................................................................... 14 Figure 12 – Detergent Probe Injection Point, 1/2" NPT ..........................................
Resumen del contenido incluido en la página 6
WARRANTY LIMITED WARRANTY Champion Industries/Moyer Diebel Limited, P.O. Box 4183, Winston-Salem, North Carolina 27115, and P. O. Box 301, 2674 North Service Road, Jordan Station, Ontario, Canada L0R 1S0 warrants machines, and parts, as set out below. Warranty of Machines: Champion Industries/Moyer Diebel Limited warrants all new machines of its manufacture bearing the name “Champion” or "Moyer Diebel" and installed within the United States and Canada to be free from defects in material and wor
