Manual de instrucciones de Snapper TP 100-400

Resumen del contenido incluido en la página 1

:.’
OPERATOR’S
MANUAL
WIDE BODY
CART COLLECTOR
Dual Wheel Cart For Use With
Turbo Collection System
SUNSTAR/ SERIES CART
SOVEREIGN/900 SERIES CART
MFG. NO. 1691526
LANDLORD/1700 SERIES CART
Form I 708219
printed in USA MFG. NO. 1692085
l/94-1GCCI

Resumen del contenido incluido en la página 2

~~: ,.~.~~ ,.. :L..~ ‘in. . : :: .:.. :.,.: ~,: ‘:, .,.: : :.

Resumen del contenido incluido en la página 3

Table of Contents Page Standard Fastener Identification Chart.. ..................................................... inside Front Cover Decals ....................................................................................................................................... 1 1 Specifications ........................................................................................................................... Decals ......................................................................

Resumen del contenido incluido en la página 4

6. Hitch and Tube Assembly - SunStar Series km Qw. 1 1 Tube Assy. (Incl. Ref. No. 38) 4 2 Nut, Hex Full, Lock, #lo-32 3 Washer, Plain, #l 0 4 4 Screw. Phillips, Truss Head, 4 #10-32x l/2 5 Hose 1 6 Clamp, 6” 1 7 Decal, Cleaning Inst. 1 8 Capscrew, Hex Hd., 7/16-14X l-1/2 4 * 9 Lo&washer, 7/16 10 Nut, Hex, Full, 7/16 4 11 2 Nut, Hex, Full, l/2-13 12 Lo&washer, l/2 2 1 13 Bracket, Hitch (Frame) 14 Nut. Hex. Full. 5/S 2 2 15 Lockwasher, s/a 16 2 Bracket, Hitch (Cart) ,114 2 17 Capscrew, Hex Hd., 5/

Resumen del contenido incluido en la página 5

3. Turn box upside down and install the frame to the U- Cart Assembly bracket (figure 4). Align the two prong end (A) in the NOTE: Sort out the hardware and arrange by size and frame with the ends of the U-bracket and secure with type. Refer to figure 1. two 112-13 x l-114 hex bolts and locknuts. DO NOT 1. Install the wheel assemblies (A, figure 2) to the overtighten the locknuts, since the box pivots at this frame (B). Place the head of the swivel wheel on the point for dumping. end of the fram

Resumen del contenido incluido en la página 6

6. Install the sleeve clamp (C, figure 11) to the connect- ing sleeve (A) with l/4-20 x l/Z slotted truss head screw (D) and nyloc nut (E). Install the connecting sleeve inside the collar of the cover and position sleeve clamp (C) over the support tube (B). ‘23!i4 Figure 13 A. Straight Rod B. Cord Loop C. Bolt Figure 11 D. Truss Head Screw, A. Connecting Sleeve l/4-20 x 112 B. Support Tube E. Nyloc Nut C. Sleeve Clamp 7. Thread the straight rod (A, figure 12) which has an eyelet on each end thro

Resumen del contenido incluido en la página 7

5. Assemble the upper tube (A) onto middle tube (B) as Discharge Tube Installation shown in figure 2 with two 1032 x l/2 truss head Landlord/1700 Series (Mfg. No. 1692095) screws (E), four flat washers (F), and two locknuts 1. Install the spring clip (D, figure 18) with two 10-32 x 63. i/2 truss head screws (E), four flat washers (F), and 6. Install two lo-32 x l/2 truss head screws (E), four two locknuts (G). flat washers (F), and two locknuts (G) to the top 2. Install l/4-20 x 5/8 carriage bol

Resumen del contenido incluido en la página 8

Operation Maintenance Grass should be cut often, and not too short. If grass is too long or lush it may be necessary to keep ground speed to a minimum or to cut only half the width to pre- The cart cover IS subject to wear and detenora- vent clogging. If grass is high, operate with mower in high cutting position. Cut the grass again in lower cutting tion. Check the cover frequently. Use an * position, if desired. The collector is full when grass builds at the window. Always operate with throttle

Resumen del contenido incluido en la página 9

TORQUE SPECIFICATIONS FOR STANDARD MACHINE HARDWARE TOLERANCE +20% SAE GRADE #5 SAE GRADE #S SIZE SAE GRADE #2 0 Q 8 InJLbs. In./Lbs. In./Lbs. Ft./Lbs. Nm. FtJLbs. Nm. Ft./Lbs. Nm. 2.1 30 3.4 41 4.6 8-32 19 8-36 20 2.3 31 3.5 43 4.9 1 O-24 27 3.1 43 4.9 60 6.8 1 O-32 31 3.5 49 5.5 68 7.7 --- I/4-20 66 7.6 8 10.9 12 16.3 8.6 10 13.6 14 19. l/4-28 76 15. 17 23.1 25 34. 5/i 6-l 8 11 5/l 6-24 12 16.3 19 25.8 25 34. 318-l 6 20 27.2 30 40.8 45 61.2 318-24 23 31.3 35 47.6 50 68. 7116-14 30 40.8 50 68.