Resumen del contenido incluido en la página 1
10-Inch Roof-Mount DVD Player
With DVD/CD/MP3 SYSTEM
AVXMTG10U
INSTALLATION
GUIDE
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS Important Notices ......................................................................................................................................... 2 Materials Included in this Package ..................................................................................................... 3 Removing and Installing Snap On Covers ..................................................................................... 4 General Vehicle Installation Approach ....................
Resumen del contenido incluido en la página 4
IMPORTANT NOTICES Installation of overhead products requires careful planning and preparation. WARNINGS Be extremely careful when working on a vehicle with side curtain air bags. • Do not use any solvents or cleaning materials when cleaning the video Do not route wires near any portion of the side curtain air bag assemblies. monitor. This includes anchor points in A, B, C or D pillars of the vehicle. Routing wires • Do not use any abrasive cleaners, they may scratch the screen. in these are
Resumen del contenido incluido en la página 5
MATERIALS INCLUDED IN THIS PACKAGE 1. 10” LCD Overhead Monitor with DVD player (1 pc) 2. 6 Pin Power Harness (1 pc) 3. 2 Pin Power / Wire Harness with Choke (1 pc) 12 3 4 4. 3 RCA Jack Pigtail (1 pc) 5. Hardware Package M5*9 (4 pcs) TA4*9 (6 pcs) 6. Remote Control (1 pc) 7. Mounting Bracket (1 pc) 8. Snap-on Shroud (2 pcs)* 5 6 7 8 9. Snap-on Screen Cover (2 pcs)* 10. Pry Tool
Resumen del contenido incluido en la página 6
REMOVING AND INSTALLING SNAP-ON COVERS Preparation Place the unit on a soft surface to avoid damaging the plastic. Materials Required 1. 2. 3. 4. Shroud Screen Cover Pry Tool 10” Overhead LCD Monitor with DVD Player Disconnecting the Screen Cover “C” “B” “A” “C” 1. Open the LCD screen. 2. Insert the supplied pry tool between the LCD screen and snap on screen cover at locations “A”, “B”, and “C” and gently pry the cover away from the screen. 4
Resumen del contenido incluido en la página 7
Installing the Screen Cover “D” “D” “D” “D” 1. Open the LCD screen. 2. Hook the two tabs “D” at the bottom edge of the screen cover into the notches on the bottom edge of the LCD screen. 3. Snap the opposite side of the screen cover over the hinges.. Disconnecting the Shroud “E” (fastener) 1. Open the LCD screen. 2. Insert the supplied pry tool between the unit and shroud at fastener location “E” and gently pry the shroud away from the unit. 5
Resumen del contenido incluido en la página 8
Installing the Shroud “F” “F” “F” Expanded view 1. Open the LCD screen. 2. Slide the shroud over the unit. The shroud will snap into place at locations “F”. 6
Resumen del contenido incluido en la página 9
GENERAL VEHICLE INSTALLATION APPROACH 1. Decide upon the system confi guration and options that will be installed. 2. Review all manuals to become familiar with electrical requirements and hookups. 3. Decide upon the mounting locations of all components and the method of mounting. 4. P rep the vehicle. Remove any interior trim necessary to gain access to vehicle's wiring, as well as all areas where interconnecting wire harnesses will be located. If any access holes need to be cut into the vehicl
Resumen del contenido incluido en la página 10
GENERAL VEHICLE INSTALLATION APPROACH Installing Unit to Roof Roof Roof Support Headliner Mounting Bracket Self-drilling Screws Video Unit M5 Screw 8
Resumen del contenido incluido en la página 11
GENERAL VEHICLE INSTALLATION APPROACH *Optional Relay Box Signal Harness To Dome Lights See “Connecting the Dome Lights” 6 Pin Power Harness 2 Pin Power Wire Harness with Choke AV IN 3 RCA Jack Pigtail 9
Resumen del contenido incluido en la página 12
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply voltage to the interior lights to turn them on. Negative switched systems apply ground to illuminate the bulbs. To determine which system you have, you must locate the wires at the dome light. On a positive switched system, with all the doors closed and lights out, both w
Resumen del contenido incluido en la página 13
Positive Switched Dome Lighting To 6 pin To Red/black-Lamp on constant connector Black/red-Lamp common +12 VDC on Monitor Purple/brown-Lamp Auto To constant +12 VDC Factory Door Ajar Switch or Body Control Computer 11
Resumen del contenido incluido en la página 14
Negative Switched Dome Lighting Red/black-Lamp on To 6 pin Black/red-Lamp common connector Purple/brown-Lamp Auto To constant +12 VDC To constant +12 VDC Factory Door Ajar Switch or Body Control Computer 12
Resumen del contenido incluido en la página 15
This page intentionally left blank. 13
Resumen del contenido incluido en la página 16
© 2010 AUDIOVOX,150 Marcus Blvd. Hauppauge, NY 11788 128-8902
