Resumen del contenido incluido en la página 1
DVR1 Series
Digital Video Recorders
Eng
Philips
Communication,
Security & Imaging
Addendum
Resumen del contenido incluido en la página 2
2
Resumen del contenido incluido en la página 3
1 REO QUICK INSTALL GUIDE ..................................................................................................................4 1.1 Introduction ........................................................................................................................................................4 1.2 Required Software Version ..................................................................................................................................4 1.3 Installation ........
Resumen del contenido incluido en la página 4
1 REO QUICK INSTALL GUIDE 1.1 Introduction This guide provides the steps necessary to install the DVR1 in combination with a REO Multiplexer or REO Switcher Monitor. If you are not familiar with the operations of the DVR1 and the REO Monitor, refer to the corresponding instruction manuals. 1.2 Required Software Version Ensure that the DVR1 and REO monitor’s software version is equal to or higher than noted below. Product Software Version DVR1 (all models) 1.14 or higher (available at www.philip
Resumen del contenido incluido en la página 5
1.4 Programming the REO System monitor No special programming is required for the REO Switcher. If using the REO Multiplexer, ensure that the Record mode is set to Multiplexing (verify this via the REO Main Menu > Settings > VCR). 1.5 Programming the DVR1 To view the DVR1’s menu screen using the REO System Monitor: • On the REO System Monitor, press MENU > SWITCH TO PLAYBACK VIEW • On the DVR1: Select MENU > ADVANCED MENU, then press ENTER Enter the correct password (default is 0000) and E
Resumen del contenido incluido en la página 6
2 INSTALLATION GUIDE FOR THE COMBINED PHILIPS MULTIPLEXER, INTUIKEY KEYBOARD & DVR1 SERIES SYSTEM 2.1 Overview ® The latest software for the Philips System4 Multiplexers, IntuiKey Keyboard, and DVR1 greatly improves the functionality of the system. This new software simplifies retrieval of the DVR1’s recorded video via the IntuiKey keyboard. 2.2 Required Software Version Ensure that the keyboard, DVR1, and Philips Multiplexer software versions are equal to or higher than those noted below. Softw
Resumen del contenido incluido en la página 7
2.4 DVR1 Keyboard Menus There are two new keyboard menus that provide direct access to the DVR1 menus and its recorded video (refer to the keyboard’s instruction manual for further information on keyboard menus). DVR1 Controls DVR1 Playback Controls 2.4.1 DVR1 Controls Menu To view the DVR1 CONTROLS menu, at the Keyboard’s MULTIPLEXER MAIN MENU, select RECORDER CONTROLS, then DVR1 CONTROLS. The multiplexer will enter the VCR View mode. When this screen is selected, the DVR1 output signal switche
Resumen del contenido incluido en la página 8
2.4.2 DVR1 Playback Controls Menu Below is a list of the new Keyboard Softkey buttons for the DVR1 Playback Controls menu along with an explanation of the functions they perform. Softkey Functions Exit • Presents the previous keyboard menu (DVR1 CONTROLS). • Output signal of the DVR1 is switched to MON A. Full, Quad, Multi Presents the various viewing options of the multiplexer. Pause, Play Forward, Play Reverse, Equivalent to the DVR1’s front panel buttons. Frame Advance, Frame Reverse, Fa
Resumen del contenido incluido en la página 9
3 RS-232 REMOTE PROTOCOL 3.1 Supported Command Sequences The DVR1 supports the following command sequences, entered via PC once communication has been established between the PC and the DVR1. The Baud Rate should be set at 9600 Baud, with 1 Stop Bit, 8 Data Bits, and Parity at None. All byte values entered at the PC must be in hexadecimal values. Each command string begins with an STX (02) character and ends with an ETX (03) character. START END COMMAND CHARACTERS 1 2 3 4 5 Play Forward FPL 02 4
Resumen del contenido incluido en la página 10
SET CLOCK Example: In this example, 14:39 on December 25, 2000 is used to demonstrate the Set Clock Command String. Notation Used in ASCII Character of Hex Value Entered Value Column Desired Value into Command String Year Character #1 y1 0 30 Year Character #2 y2 0 30 Month Character #1 m1 1 31 Month Character #2 m2 2 32 Day Character #1 d1 2 32 Day Character #2 d2 5 35 Hour Character #1 h1 1 31 Hour Character #2 h2 4 34 Minute Character #1 f1 3 33 Minute Character #2 f2 9 39 The final Set Cloc
Resumen del contenido incluido en la página 11
11
Resumen del contenido incluido en la página 12
3935 890 41811 02-18 © 2002 by Philips Electronics N.V. © 2002 by Philips Communication, Security & Imaging, Inc. All Rights Reserved. Philips ® is a registered trademark of Philips Electronics N. A. Corp. Data subject to change without notice
