Resumen del contenido incluido en la página 1
Model #: CVDVR200
User Manual
now you can see
www.svat.com
Resumen del contenido incluido en la página 2
INTRODUCTION Thank you for purchasing the SVAT DVR200 DVR system. To ensure that you are getting the most out of this system please read this entire manual before you install the system. Also, be sure to keep this manual for future reference in case any problems or questions should arise. Enjoy your DVR200! IMPORTANT SAFETY INFORMATION When using your DVR equipment, basic safety precautions should always be fol- lowed to reduce the risk of fire, electric shock and personal injury. Please read th
Resumen del contenido incluido en la página 3
CONTROL PANEL AND FUNCTION FRONT PANEL View Control Buttons 1. Mobile Rack 15. View Full Screen from Camera 1 2. Key Socket 16. View Quad Screen and display 3. Hard Disk in-use Indicator all cameras 4. Power Indicator 17. View Full Screen from Camera 2 18. View Full Screen from Camera 3 Playback Control Buttons 19. View Full Screen from Camera 4 20. Remote Control Socket 5. Rewind Playback button 6. Stop Button 7. | |Pause Button REAR PANEL 8. Fast Forward and Skip Button 21. Video Output Te
Resumen del contenido incluido en la página 4
INSTALLATION 1. Hard Disk installation The system supports Dual Hard Disk recording feature. Please carefully follow the steps as below to install Hard Disk Driver. Install the Hard Disk into mobile rack 1.Take out the 2.Take off the 3. If you decide to use two mobile rack. top cover Hard Disks in the colour mintor with the DVR system. you have to designate one as a master and the other as a slave. 4. Connect the cable 5.Screw the hard 6.Close the top cover and and power cord. disk on. i
Resumen del contenido incluido en la página 5
SENSOR & ALARM INSTALLATION 2. Alarm Connect the wire of alarm one pin to alarm terminal, the other pin of the wire connect to the DC power wire pin as the following picture showed. The other pin of adapter (power) wire connect to the alarm terminal. VIDEO INPUT * If the sensor or alarm you purchased is different from above instruction, please refer to the manual with the sensor/alarm. OPERATION The Factory has preset various functions as following list. If it can meet your usage requirement, pl
Resumen del contenido incluido en la página 6
OPERATION CONTINUED The default setting on the SUB-MENU SUB MENU > PASSWORD CHANGE (Default setting 111111) TIME SET 2003/01/01 01:01:00 FULL SCREEN BY SENSOR OFF SEQUENT VIEW TIME OFF PRESS (< , >) THEN (SELECT) PRESS (MENU) TO EXIT The default setting on the HARD DRIVE SETUP HARD DRIVE SET UP > OVERWRITE ENABLED YES MASTER HDD SIZE (Depends on HDD you choose) MASTER HDD USED MB % MASTER HDD FORMAT (for format master HDD) SLAVE HDD SIZE (Depends on HDD you choose) SLAVE HDD USED MB % SLAVE HDD
Resumen del contenido incluido en la página 7
OPERATION CONTINUED Watch & View Control 1. This View button controls FULL SCREEN display from camera 1. 2. This View button controls FULL SCREEN display from camera 2. 3. This View button controls FULL SCREEN display from camera 3. 4. This View button controls FULL SCREEN display from camera 4. 5. This View button controls QUAD SCREEN, displays all cameras. In the HARD DRIVE SETUP menu, the system will display the hard disk usage. Record Control 1. When the red [RECORD] button is pressed, the r
Resumen del contenido incluido en la página 8
OPERATION CONTINUED REMARK The event logging maximum can record 95 events for each hard disk, but the screen can only show 7 events. If the events are more than 7 and the select mark stays on the 7th event, press [ ] key once will roll up the next event till the last event is shown. If the events are more than 95, the old recorded information will be stored in HDD too. The user can playback it by button in search time. To select playback by SEARCH TIME 1. Press button to skip the select mark [>
Resumen del contenido incluido en la página 9
MENU SETTINGS Main Menu Setting Main Menu > CAMERA SELECT 1234 RECORD SELECT 1234 RECORD MODE EACH RECORD FRAMERATE 30 VIDEO QUALITY NORMAL RECORD SCHEDULE Default setting 0~24 record. SUB MENU HARD DRIVE SETUP SENSOR SETUP NETWORK SETUP PRESS (< , >) THEN (SELECT) PRESS (MENU) TO EXIT Camera Select 1. When CAMERA SELECT option is selected, 4 different images from all cameras are initially displayed. (The default setting is 1234 all cameras on.) 2. Use the view button on the front panel to sele
Resumen del contenido incluido en la página 10
MENU SETTINGS Record Frame Rate 1. When RECORD FRAME RATE is selected, you may choose the following recording frame rate - 30, 15, 10, 7, 5, 4, 3, 2 or 1 fps for recording. 2. The higher the record frame rate is, the more natural the look will be displayed on the screen when you playback. The lower the record frame rate is, the more the capacity you can save on the hard disk driver. Video Quality When VIDEO QUALITY is selected, there are three different video quality LOW, NORMAL or HIGH reso
Resumen del contenido incluido en la página 11
MENU SETTINGS 4. When the new password is accepted, the system will flash the following screen message: Password Change !!! 5. The message will flash 5 times. 6. Then, it will be back to the SUB MENU If the password is not accepted, you will receive a message to inform you: Password Incorrect , then return to the SUB MENU . You may try again by repeating the same steps. Time Set 1. Below is a screen shot of the Time Menu screen, you can change time/date/hour/year by using TIME SET menu. TIME
Resumen del contenido incluido en la página 12
MENU SETTINGS 1. Overwrite Enabled If you choose [YES], the recording will continue and overwrite previous recording when all hard disk driver capacity is full. If you choose [NO], the recording session stops when all hard disk driver capacity is full. 2. Master HDD Size It shows the size of the Master hard disk driver installed in the DVR. 3. Master HDD Used It shows the capacity used on the Master hard disk driver for recording. 4. Master HDD Format If you format the hard disk driver, it wil
Resumen del contenido incluido en la página 13
MENU SETTINGS Alarm Out Time When you select ALARM OUT TIME , the number indicates how long (in seconds) the alarm lasts after the sensor detected the motion signal. If you set CONT, the alarm will keep continuous when sensor detected the motion signal. If you set OFF , the alarm will not function when sensor detected the motion signal. Sensor Type Setup When you select SENSOR TYPE SETUP, you can select NOT INSTALLED, NORMAL OPEN type or NORMAL - CLOSE type sensor to make setting for each c
Resumen del contenido incluido en la página 14
TROUBLE SHOOTING The power indicator is OFF on the DVR. 1. Check and see if the AC power cord is connected properly. 2. Check and see if the power outlet on the wall is working. 3. Is the power outlet on the wall controlled by a wall switch? If it is, make sure the switch is on. The DVR can not be turned on. 1. Check and see if the hard disk is correctly installed and properly locked. 2. Please note the power cannot be entered if the key socket is not locked. Can not play the DVR 1. Check the
Resumen del contenido incluido en la página 15
TROUBLE SHOOTING When Record does not work. Check the system and see whether it is in Play Mode, press button to stop Play Mode. Then, you can enter the RECORD function. When you forgot the password Please contact your distributor or engineer to solve this problem. To avoid this, have your password stored in a secure place away from the unit. Can’t stop Record function. The system is working with key lock function. If the system setting is with key lock while recording, you are requested to ke
Resumen del contenido incluido en la página 16
For Further Assistance call: 1.866.946.7828 now you can see www.svat.com
