Resumen del contenido incluido en la página 1
OWNER'S
UAL
Model No.
139.53535SRT1
139.53644SRT
139.53647SRT1
I:RRFTSMRNo
1/2 P
GARAGE DOO OPENE
For Residential Use
Only
[] Safety Precautions
Caution:
[] Assembly
Read and follow all
[] installation
safety rules and
[] Adjustment
operating instructions
[] Care and Maintenance
before first use of this
[] Operation
product.
[] Troubleshooting
[] Parts List
Fasten the manual
near the garage door
after installation,
Complies with UL 325 _11 "_
regulations effective
January I, I993
Sears, Roebuck
Resumen del contenido incluido en la página 2
Contents Page Contents Page A review of safety alert symbols ................................. 2 Install the lights and lenses ...................................... 19 You'll need tools .......................................................... 3 Attach emergency release rope and handle ...........19 Safety information regarding garage door Electrical requirements ............................................. 20 locks and ropes ......................................................... 3 Safety
Resumen del contenido incluido en la página 3
You'll Need Tools During assembly, installation and adjustment of the opener, instructions will call for hand tools shown below. Pencit Carpenter's Level Hack Saw Tape Measure Wire Cutters CIaw Hammer 5/32" Drilt Bits Dritt 3/16", 5/16" and ts Screwdriver Stepladder Adjustable End Wrench An unbalanced garage door might not reverse To avoid damage to the garage door and when required and someone under the door opener, disable locks before installing and operating the opener. Use a wood screw or n
Resumen del contenido incluido en la página 4
Before you begin, survey your garage area to see whether any of the conditions below apply FINISHED CEILING to your installation. Support bracket & fastening hardware is required. Horizontal and vertical reinforcement See page 17. is needed for lightweight garage doors Slack in Chain Tension (fiberglass, steel, aluminum, door is Normal When with glass panels, etc.). See page 24 for details. Garage Door is Closed \ Header Wall Extension Spring OR Access Door Torsion Spring i ii O Safety Reversing
Resumen del contenido incluido en la página 5
One-Piece Door without Track Before you begin, survey your garage area to FINISHED CEILING see whether any of the conditions below apply Support bracket & fastening to your installation. hardware is required. See page 17. Slack in chain tension is normal when garage door is closed. Header Wall Closed Position Cable Pulley Bracket Cable Trolley Access Door \ Header Bracket © Door Bracket Emergency Release Straight Curved Rope & Handte Door Door Arm Arm Door [ Reversin_ ) between floor and bottom
Resumen del contenido incluido en la página 6
Carton inventory Your garage door opener is packaged in two cartons which contain all parts illustrated below. If anything is missing, carefully check the packing material. Parts may be "stuck" in the foam. Hardware for assembly and installation is shown on page 7. Model 53644 only Models 53535 (2), 53644 (2), 53647 (1) Three-Function Remote Control with Visor Clip Multi-Function Premium Control Console Keyless Entry Light Lens (2) White & White/Red 2-Conductor Bell Wire Sprocket Cover /_ Trolle
Resumen del contenido incluido en la página 7
Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation procedures. Assembly Hardware i Washered Screw Hex Screw Nut Carriage Botts 5/16"-18x 1/2" (2) 5/16"-18x7/8" (3) 5/16"-18 (5) Master Link (2) 1/4"-20xl/2" (4) (mounted in opener) © © Lock Nut Lock Washer Trotley 1/4"-20x7/16" (4) 5/16" (4) Threaded Shaft (1) Installation Hardware Rail Grease 0 5/16"-18x7/8" (4) Ring Fastener (3) © l E I I E I I I E I I I_ © Lag Scre
Resumen del contenido incluido en la página 8
Assembly Section: Pages 8 - 11 To avoid installation difficulties, do not run the garage door opener until instructed to do so. Make sure bolt necks are Assembly Step 1 seated in the square Assemble the T=rail & aligned before you Attach the Cable Pulley Bracket tighten lock nuts. (See right and wrong views). I J holesandrailsare __ Improper assembly can • Place the 3 T-rail sections on a flat surface for cause jerky trolley assembly. The end sections are identical. Make operation, noise and/or
Resumen del contenido incluido en la página 9
Hardware Shown Assembly Step 2 Actual Size install the Trolley on the T-rail © * Attach the threaded shaft to the trolley with the lock washer and nuts as shown. Lock Washer Nut 5/16" 5/16"-18 Lock Washer 5/16" Outer Nut Trolley Threaded Shaft Inner Nut 5/16" Trolley Temporary Stop Screwd river * As a temporary stop, insert a screwdriver into the \ hole in the front end of the T-rail. , Slide the trolley assembly along the rail to the screwdriver stop. if trolley hits against any nuts on the T-r
Resumen del contenido incluido en la página 10
Assembly Step 4 Install the Chain/Cable & Serious injury can result if fingers become Attach the Sprocket Cover entangled in moving opener sprocket. Attach sprocket cover securely. Never operate opener while your hand is near the opener sprocket. Dispensing Carton Opener Figure 2 Sprocket Leave Chain and Cable Inside Dispensing Carton to Prevent Kinking. Keep Chain and Cable Taut When Dispensing • Detach the cable loop from the carton and fasten it to the trolley with a master link from the hard
Resumen del contenido incluido en la página 11
Assembly Step 5 Tighten the Chain & Cable Lock Outer Nut Washer Inner Nut • Spin the inner nut and lock washer down the "\ // threaded shaft, away from the trolley. • To tighten the chain, turn outer nut in the direction shown. As you turn the nut, keep the chain ................. i' ................ q -TO_tuet_ -- from twisting. • When the chain is approximately 1/2" above the TroIl_ base of the T-rail at its midpoint, re-tighten the inner nut to secure the adjustment. Sprocket noise can result
Resumen del contenido incluido en la página 12
installation Section: Pages 12- 27 installation Step 1 Determine Header Bracket Location If the header bracket is not rigidly fastened to Installation procedures vary according to a structural support on the header wall or garage door types. Follow the instructions ceiling, the safety reverse system may not which apply to your door. work properly (see page 30). The door might not reverse when required, and could cause serious injury or death. The garage door springs, cables, pulleys, brackets an
Resumen del contenido incluido en la página 13
Read the Safety instructions on page 12. They also apply to doors without tracks. Header Wall VerticaI Centerline 2x4 * Close the door and mark the inside vertical centerline of your garage door. Extend the line onto the header wall above door. If headroom clearance is minimal, you can install the header bracket on the ceiling. OPTIONAL CEILING MOUNT See page 14. FOR HEADER BRACKET , If you need to instafl the header bracket on a 2x4 (on waft or ceiling), use lag screws (not suppfied) to securel
Resumen del contenido incluido en la página 14
Youcanattach the header bracket either to the wall above the garage door, or to the ceiling, Follow the instructions which will work best for your particular requirements. Fasten the Header Bracket to the Wall • Center the bracket on the vertical guideline with * Mark either set of bracket holes (do not use the the bottom edge of the bracket on the horizontal holes designated for ceiling mount). Drill 3/16" pilot line as shown (with the arrow pointing toward the holes and fasten the bracket secu
Resumen del contenido incluido en la página 15
installation Step 3 Attach the T=rai! to the Header Bracket • Position the opener on the garage floor below the header bracket. Use packing material as a --Header Wall protective base. Header if the door spring is in the way you'll need help. Bracket Have someone hold the opener securely on a temporary support to allow the T-rail to clear the Cable spring. Pulley Bracket • Position the cable pulley bracket against the header bracket. • Align the bracket holes and join with a clevis pin as shown.
Resumen del contenido incluido en la página 16
installation Step 4 Position the Opener Follow instructions which apply to your door type as illustrated. A 2×4 laid fiat is convenient for setting an ideal door-to-T=rail distance. 2x4 Laid Flat • Raise the opener onto a stepladder. You will need help at this point if the ladder is not tail enough. •Open the door all the way and place a 2x4 laid flat Door on the top section beneath the T-rail. If the top panel hits the trolley when you raise the door, pull down on the trolley release arm to dis
Resumen del contenido incluido en la página 17
installation Step 5 Hang the Opener Two representative installations are shown. Yours may be different. Hanging brackets should be angled, Figure 1, to provide rigid support. On Figure 1 finished ceilings, Figure 2, attach a sturdy metal bracket to structural supports before installing the opener. The bracket and fastening hardware are not supplied. See accessory page 38. Measure the distance from each side of the opener to the structural support. • Cut both pieces of the hanging bracket to requ
Resumen del contenido incluido en la página 18
installation Step 6 Install the Premium Control Console Do not connect to live electrical wiring. Connect only to 24 Volt low voltage wires. Connection to Locate the door control within sight of the door live wires or higher voltage may cause serious at a minimum height of 5 feet where small injury from shock, burn or electrocution. children cannot reach, and away from all moving Children operating or playing with a garage parts of the door and door hardware. door opener can injure themselves or
Resumen del contenido incluido en la página 19
6.AttachtheUserSafetyInstruction labeltothewall Do NOT connect the power and operate the nearthedoorcontrol, andtheMaintenance opener at this time. The trolley will travel to the Instruction labelina prominent location onthe full open position but will not return to the inside of thegarage door. close position until the sensor beam is connected and properly aligned. Page32explainshowto usethedoorcontrol. See Safety Reversing Sensor instructions beginning on page 21. Installation Step 7 I Instafl
Resumen del contenido incluido en la página 20
installation Step 9 Electrical Requirements To prevent electrocution or fire, installation and wiring must be in compliance with local electrical and building codes. To reduce the risk of electric shock, your garage Do NOT use an extension cord, 2-wire adapter, door opener has a grounding type plug with a third grounding pin. This plug will onlyfit into a grounding or change the plug in any way to make it fit your outlet. type outlet. If the plug doesn't fit into the outlet you have, contact a q
