Manual de instrucciones de Dakota Alert Inc.,inc. wireless pir sensor

Resumen del contenido incluido en la página 1

IR-3000
Wireless PIR
Sensor
Owner’s Manual

Resumen del contenido incluido en la página 2

Warnings This device complies with Part 15 of the FCC rules, Operation of this device is subject to the following conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference, including interference that may cause unde- sired operation. Introduction: The IR-3000 is a wireless PIR sensor that is com- patible with the Dakota Alert 3000 Series of transmitters and receivers. The IR-3000 is designed for indoor applications or outdoor applications

Resumen del contenido incluido en la página 3

PIR settings: Loosen the phillips screw on the bottom of the case and swivel the top cover up to reveal the PIR board (figure 1). (The screw is captured in the case and will not come completely out.) The jumper settings are as follows: Detection Range: High - 40 feet Medium - 25 feet Low - 12 feet LED: ON - led will flash when it detects OFF - led is always dark Filter: ON - set for outdoor use OFF - set for indoor use Reset: 15 seconds to reset after activati

Resumen del contenido incluido en la página 4

2. Locate the 10 dip switches on the transmitter module (figure 3). 3. The first eight dip switches are for the frequency setting (256 combinations). Set switches 1-8 (figure 3-3) to match the eight switches in the receiver.3. Switches 9 and 10 (figure 3-4) are for zone/channel setting on the transmitter. The four zones are listed below. Switch Switch Channel 12-volt Tune 9 10 DC output On On 1 Yes Classical Off On 2 No Westminster On Off 3 No Ding Dong 4 Off Off 4 No Whistle 3 figure 3 L

Resumen del contenido incluido en la página 5

Setting the detection area: The IR-3000 comes with a user modifiable mask on the lens (figure 4) to adjust the width of the de- tection area from approximately 16˚ to 100˚. The mask comes in two pieces, and fits into the slots above & below the lens cover. Each half of the mask is perforated and can broken into three sep- arate strips (figure 4). Each strip of the mask rep- resents approximately 16˚ of viewing angle. The user breaks off the appropriate number of strips to provide t

Resumen del contenido incluido en la página 6

Swivel Mount The IR-3000 has a swivel mount (figure 6) which also provides for adjustment of the detection area. o o The mount can be adjusted right or left up to 80 and up or down up to 50 . The swivel mount can be attached to the desired surface with the provided mount- i n g screws. The sensor is then attached to the mount using the notch on the back (figure 6). NOTE: The mount will slide easily into the slot and lock into po- sition one way only. If the mount does not slide into th

Resumen del contenido incluido en la página 7

Troubleshooting the IR-3000 Although the IR-3000 should be very reliable, there are occasions when you might have false alarms or a failure to alert. If you are getting false alarms, please try this: • S e t fi l t e r ju m p e r t o “ O N ” . • D e c r e as e r a n g e ju m p e r . • M a k e s u r e t h a t t h e t r a n sm i t t e r i s n o t p o i n t i n g a t a r o a d i n t h e d i s t a n c e . • T he sun ma y be causing false sig nals; tr y t o r eloca t e

Resumen del contenido incluido en la página 8

WARRANTY Dakota Alert warrants this product to be free of defects in material and workmanship for a period of one year from the date of purchase. This warranty does not cover damage resulting from accident, abuse, act of God or improper operation. If this product does become defective, simply return it to Dakota Alert. Please include a note describing the troubles along with your name and return address as well as the original sales receipt. If the product is covered under warranty it will