Resumen del contenido incluido en la página 1
SIPSD37X & HTSD37X
37X Optical Indoor / Outdoor Speed Dome Cameras
200 New Hightway
Amityville, NY 11701
631-957-8700
www.specotech.com
Speco Technologies is constantly developing product improvements. We reserve the right to
modify product design and specifications without notice and without incurring any obligation.
Rev. 03082010.
Resumen del contenido incluido en la página 2
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT OPEN THE COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONAL This lightning flash with arrowhead symbol is intended to alert the user to the presence of un-insulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. This exclamation
Resumen del contenido incluido en la página 3
NOTICE Important Safety Guide 1. Read and follow all the Instructions Read all the safety and operating instructions before using the product. 2. Keep this manual Keep this manual for reference in future. 3. Attachments / Accessories Use only the attachments or accessories specified by the manufacturer. 4. Installation Do not install near any heat sources such as radiators, heat registers, stoves, or other appratus including amplifiers that product heat. Impro
Resumen del contenido incluido en la página 4
NOTICE Caution Operating Before using, make sure that the power supply is properly installed. While operating, if any abnormal condition or malfunction is observed, stop using the product immediately and then contact your local dealer. Handling Do not disassemble or tamper with the parts inside the product. Do not drop or subject the product to shock and vibration as this can damage the product. Care must be taken when you clean the clear dome cover. Especially,
Resumen del contenido incluido en la página 5
TABLE OF CONTENTS ① Introduction Features 6 Package Components 9 Main Part Description 10 ② Installation DIP Switch Setup 11 Installation with Wall Mount Bracket 14 Wiring and Cabling 15 ③ Operation Check Points before Operation 18 Check Points for Preset and Pattern Function before 18 Operation OSD Menu
Resumen del contenido incluido en la página 6
INTRODUCTION 1 Features Powerful Zoom Camera & Setup Options Image Sensor: Sony 1/4" Double density interline transfer CCD Zoom: 37X Optical Zoom, 12X Digital Zoom Day & Night, Privacy Mask and WDR SNR (Super Noise Reduction) Function Various Focus Modes: Auto-Focus, Manual Focus, Semi-Auto Focus Various Setup Options in OSD Menu. Powerful Pan/Tilt Functions MAX. 360 °/sec High Speed Pan/Tilt Motion With the Vector Drive Technology, Pan/Tilt motions
Resumen del contenido incluido en la página 7
INTRODUCTION 1 MAX. 8 sets of Swing are programmable. This function is that the camera moves repetitively between two preset positions at programmed speeds. MAX. 4 Patterns are programmable. This function is that the camera memorizes the path (mostly curve path) by the joystick of the controller and revives the trajectory operated by the joystick as closely as possible. MAX. 8 sets of Group are programmable. This function is that the camera memorizes the combination of Presets,
Resumen del contenido incluido en la página 8
INTRODUCTION 1 Network Function(Only for the SIPSD37X) Network functions including remote monitoring, bidirectional audio and others are available through IP based network such as LAN, ADSL/VDSL, and Wireless LAN. For more information, refer to the separated manual for IP Addressable models. Perfect Outdoor Environment Compatibility and Easy Installation The fans and heaters are built-in in the camera for cold and hot temperature environment. Also idealistic mechanical design
Resumen del contenido incluido en la página 9
INTRODUCTION 1 Package Component Product & Accessories Main Body & Surface Mount Bracket Default Accessories [Main Cable, Wrench] Accessories for The Models with Alarm Accessories for The IP Addressable Models In/Out Function [I/O Cable] [Crossover LAN Cable, Audio Cable, CD] SIPSD37X Only Wall Mount Brackets (Included) [Screws : Machine M5 ×15, Hex Lag #14 ×50] 37X Speed Dome Camera 9/50
Resumen del contenido incluido en la página 10
INTRODUCTION 1 Main Part Description Mounting Screw Hole Drop Prevention Spring Reset Switch (IP Model) DIP Switch LAN Port (IP Model) Audio Port (IP Model) Main Connector Sensor I/O Port (I/O Model) Dome Cover Dome Cover Do not detach the protection vinyl from the dome cover before finishing all the installation process to protect the dome cover from scratches or dust. DIP Switch Used to set up camera IDs and protocols. Drop Prevention This part keeps the camera fro
Resumen del contenido incluido en la página 11
INSTALLATION 2 DIP Switch Setup Before installing the camera, set up the DIP switch to configure the camera ID and the communication protocol. Camera ID Setup ID numbers of cameras are set up with binary numbers. ON ON See the examples shown below. Pin 1 2 3 4 5 6 7 8 12 3 4 56 78 Binary Value 1 2 4 8 16 32 64 128 ex) ID=5 on off on off off off off off ex) ID=10 off on off on off off off off The camera ID range is “1~255”. Camera ID must not be “0”!
Resumen del contenido incluido en la página 12
INSTALLATION 2 Communication Protocol Setup Select an appropriate Protocol with the DIP switch combination. ON ON Switch Mode Protocol P0 P1 P2 12 3 4 (Pin 1) (Pin 2) (Pin 3) OFF OFF OFF PELCO-D, 2400 bps ON OFF OFF PELCO-D, 9600 bps OFF ON OFF PELCO-P, 4800 bps ON ON OFF PELCO-P, 9600 bps Others Reserved Match the camera protocol with the camera protocol in the setting of your DVR or controller to control the camera. Adjust the DIP switch afte
Resumen del contenido incluido en la página 13
INSTALLATION 2 Terminal Resistor Setup The terminal resistor is used for the following cases. ON ON Case 1 : In case that the control cable length between a camera and a controller is relatively very long (1:1 Connection) 12 3 4 If the communication cable length is very long, the electrical signal will bound in the terminal point. This reflected signal causes distortion of original signal. Accordingly, the camera can be out of control. In this case, the terminal resistor of b
Resumen del contenido incluido en la página 14
INSTALLATION 2 Installation with Wall Mount Bracket ① Make a hole whose diameter is 30~40mm ② Hook up “Drop Prevention Spring” on on the mounting surface to pass the main body to prevent camera from wire(s) and cable(s) through the mounting unexpected drop and pull the wire(s) and surface. (In case of the wiring and cabling cable(s) for the system as below. through the mounting surface only) Then prepare the wall mount bracket. Pull the wire(s) and cable(s) for the syste
Resumen del contenido incluido en la página 15
INSTALLATION 2 Wiring and Cabling POWER INTERNET LAN CABLE BROWSER BNC MAIN CABLE MONITOR AUDIO MIC SPEAKER CABLE RS-485 CONTROLLER / DVR I/O CABLE SENSOR I/O IR DOOR SENSOR SWITCH Port Description Main Cable Port Pin Number (RJ45) Connector / Wire Color Signal 1 Video + BNC Connector 2,4 Video − 5 Red RS-485 + 3 Yellow RS-485 − 7 Orange Power + 6,8 White Power − I/O Cable Port Pin Nu
Resumen del contenido incluido en la página 16
INSTALLATION 2 Power Description Carefully check the voltage and current capacity of the rated power. The rated power is indicated in the back of main unit. 24VAC is used on the HTSD37X (AC 17V~29V, 1.5A) 12VDC is used on the SIPSD37X (DC11V~18V, 3.0A) For the DC input models, be careful with the polarity of DC power. The system should be permanentally damaged by wrong DC input. In case that the length of the power wire is very long, there may be voltage drop and the syat
Resumen del contenido incluido en la página 17
INSTALLATION 2 Video Use BNC coaxial cable only. Alarm Input Internal +5V~12V IN COM+ + - Sensor 1 + - IN 1- IN 3- Sensor 3 + - Before connecting sensors, check driving voltages and output signal types of the sensors. Since output signal types of the sensors are divided into Open Collector type and Voltage Output type in general, the wiring must be done properly after considering those types. Signal Description IN COM+ The electric power source to drive input
Resumen del contenido incluido en la página 18
OPERATION 3 Check Points before Operation Before turning on the system, check if the wire(s) and cable(s) are connected properly. Check if the camera ID on the controller is properly selected. The camera ID must be identical to that of the target camera. The camera ID can be checked by reading the DIP switch of the camera or on OSD. If your controller supports multi-protocols, the protocol must be changed to match to that of the camera. Adjust the DIP switch after tu
Resumen del contenido incluido en la página 19
OPERATION 3 OSD Menu Function With OSD menu, the system can be properly configured for each application. Entering into OSD Go Preset [95] Reserved Presets (Hot Keys) Description Some Preset numbers are reserved to change some parameters without entering into OSD menu. Hot Keys Go Preset [95] : Entering into OSD menu Go Preset [131~134] : Running Pattern Function 1 ~ 4 Go Preset [141~148] : Running Swing Function 1 ~ 8 Go Preset [151~158] : Running G
Resumen del contenido incluido en la página 20
OPERATION 3 Preset Function MAX. 127 positions are programmable. The Preset number can be assigned from 1 to 128 except 95. Preset 95 is reserved for entering into OSD menu. Camera parameters such as White Balance, Auto Exposure and others can be set up independently and each preset can have its own parameter values independently from the other persets. When setting up presets with a controller, Label should be blank and "Camera Adjust" should be set to "GLOBAL" as the
