Manual de instrucciones de American Standard Chandler Americast 7182.000

Resumen del contenido incluido en la página 1

™
Installation
Instructions
CHANDLER™ AMERICAST™ ISLAND SINK
WITH FAUCET HOLES 7182.001/7182.803
WITHOUT FAUCET HOLES 7182.000
Certified to comply with ANSI A112.19.4.M
Thank you for selecting American-Standard...the benchmark
U.S. Patent No. 4,664,982
Other patents pending.
of fine quality for over 100 years.
CAN/C.S.A. B-45
To ensure that your installation proceeds smoothly--please
Observe local plumbing and building codes.
read these instructions carefully before you begin.
791267-400 Rev. C

Resumen del contenido incluido en la página 2

AFTER THE CUTOUT IS DRAWN... Apply a masking tape Cutout 1 5 Drill a clearance hole outline 1/8" outside inside the cutout line Perimeter traced outline as a as marked on the of sink guide for application countertop. of silicone Sink Masking 1/8" sealant. outline tape outline Cutout Apply a generous portion of silicone sealant inside line 6 Perimeter traced on countertop. Carefully lower sink into place 2 of sink Cut opening on cut and press down firmly. Use guidelines for proper line in

Resumen del contenido incluido en la página 3

™ ® AMERICAST BRAND Installation SINKS Instructions UNDERCOUNTER MOUNTING FOR CHANDLER, LAKELAND, PALISADE AND SILHOUETTE™ KITCHEN SINKS MODELS 7145, 7162, 7163 STANDARD, 7103, 7172, 7173, 7179, 7182, 7183, 7185, 7196, 7255 Thank you for selecting American-Standard...the Certified to comply with ANSI A112.19.4.M benchmark of fine quality for over 100 years. U.S. Patent No. 4,664,982 Other patents pending. To ensure that your installation proceeds smoothly--please CAN/C.S.A. B-45 read these in

Resumen del contenido incluido en la página 4

IMPORTANT: DIMENSIONS OF FIXTURES ARE NOMINAL AND MAY VARY WITHIN THE RANGE OF TOLERANCESESTABLISHED BY A.N.S.I. AND C.S.A. STANDARDS. SUPPORT CLIP LOCATIONS: 838mm 1054mm (33) (41-1/2) SUPPORT 559mm 559mm CLIPS (22) (22) SUPPORT CLIPS MODEL 7145, 7163 STANDARD,7179 MODEL 7183 914mm 965mm (36) (38) 559mm SUPPORT 559mm (22) CLIPS (22) SUPPORT CLIPS MODEL 7196 MODEL 7255 419mm 457mm (16-1/2) (18) SUPPORT SUPPORT 381mm 457mm CLIPS CLIPS (15) (18) MODEL 7185 MODEL 7182.801/803 711mm (28) 419mm 314

Resumen del contenido incluido en la página 5

5 The following instructions are for NOTE countertop mounted fittings only. Apply a bead of sealant to Countertop (Silhouette single bowl shown) the edge of the sink. Hold the Cutout sink against the under-side of Edge the countertop and rotate Sealant 1 the clips to hold the sink in Countertop place. Snug the screws to hold the sink. Attach all the Template additional clips. Drill a clearance hole 41mm inside the cutout line. (1-5/8) Support Clip Cutout template 6 2 Cut opening on cut

Resumen del contenido incluido en la página 6

INSTALLATION B — FITTINGS MOUNTED DIRECTLY ON SINK Refer to American Standard roughing-in information for specific dimensions for each model. Below are the dimensions of each sink. Make sure this area is available to mount the sink. Unfold the template and refer to the instructions below. CAUTION 1. Minimum countertop thickness is 19mm (3/4) for wood and 12mm (1/2") for marble and solid surface materials. SINK CUTOUTS: Locate and mark center lines of sink on countertop. Provide proper clea

Resumen del contenido incluido en la página 7

The following instructions are for NOTE 4 Apply a bead of sealant to Countertop mounting fittings directly to the sink. Cutout the edge of the sink. Hold the (Silhouette single bowl shown) Edge sink against the under-side of Sealant the countertop and rotate the clips to hold the sink in 1 Countertop place. Snug the screws to hold the sink. Attach all the Template Drill a clearance hole additional clips. 41mm inside the cutout line. (1-5/8) Support Clip Cutout template 5 Countertop Sink