Manual de instrucciones de Chief Manufacturing Wall Mount PLP Series

Resumen del contenido incluido en la página 1

INSTALLATION INSTRUCTIONS
PLP Series Wall Mount
The PLP Series wall mount accommodates large flat
screens weighing up to 200 lbs (90.72kg). The teardrop
holes in the mount allow for quick connect/disconnect of
the screen, thus simplifying installation and maintenance
processes.
The top and bottom mounting brackets are adaptable to
supporting framework with wood studs that are 16” on
center or 24”on center.
The mount has integrated lateral shift, allowing for four
different mounting options. Fo

Resumen del contenido incluido en la página 2

Installation Instructions PLP Series ! IMPORTANT: If the installation of this product requires OSHPD seismic approval, refer to OSHPD pre-approval documents and drawings before beginning installation. OSHPD documents and drawings are available at www.chiefmfg.com, and located on the product information page for the mount. BEFORE YOU BEGIN CAUTION: To prevent damage to your monitor and PLP, which could affect or void the Factory warranty, thoroughly study all instructions and illustrations be

Resumen del contenido incluido en la página 3

Installation Instructions PLP Series DIMENSIONAL DRAWING 26.00 TOP MOUNTING BUTTON ON PSB-XXXX DRAWING GOES HERE 24.00 16.00 16.00 1.83 16.00 .69 C 1.87 15.51 18.38 17.00 13.19 4.24 FACE TILTS 15 DOWN 7 UP (FOR SERVICE) NOTE: CUSTOM INTERFACE BRACKET NOT SHOWN. THE CUSTOM INTERFACE BRACKET NEEDED FOR YOUR DISPLAY WILL ADD BETWEEN 1/2" AND 2" IN DEPTH AND MAY AFFECT LOCATION OF DISPLAY ON THE MOUNT. SEE PSB-XXXX DRAWING ALSO. 5/16" x 1" SLOT 5/16" x 6" SLOT 5/16" x 1" SLOT 3

Resumen del contenido incluido en la página 4

Installation Instructions PLP Series PARTS LIST CONTENTS Prior to assembly, unpack the carton completely. Verify DIMENSIONAL DRAWING ..................................... 3 contents listed in Table 1 and Figure 1. TOOLS REQUIRED FOR INSTALLATION.............. 4 Read installation instructions completely. If you are PARTS LIST .............................................................. 4 missing any of the listed parts, contact Customer Service PLP INSTALLATION..................................

Resumen del contenido incluido en la página 5

Installation Instructions PLP Series PLP INSTALLATION Perform the following procedures to mount the PLP. Hang the mount on the wall temporarily Select Mounting Location using a nail in the center hole. Level the To select the mounting location, do the following: mount before drilling WARNING: It is the responsibility of the installer to pilot holes. verify that the wall to which the mount is anchored will safely support the combined load of all attached Figure 2. Use Triangular Hole to Hang the

Resumen del contenido incluido en la página 6

Installation Instructions PLP Series PLP INSTALLATION (Cont’d) Mount the PLP To mount the PLP, do the following: Option A 1. Holding the PLP against the wall, select the pair of mounting holes that best suits your situation (see Figures 5, 6, and 7). NOTE: The mounting holes are slotted to allow for a small degree of lateral movement. The mount can be centered, or shifted to the left of center, or right of center depending on stud location. 2. Depending on your situation, install the lag bolts a

Resumen del contenido incluido en la página 7

Installation Instructions PLP Series ATTACH PSB TO THE DISPLAY To attach the PSB to the display, do the following: Display To help your identify the correct PSB that matches the model number of your display, refer to the cross- reference chart at www.chiefmfg.com. To download the corresponding PSB installation instructions, refer to www.chiefmfg.com. OR Contact Customer Service at 952-582-6480 if you have any questions about how to select the PSB that matches the model number of your display.

Resumen del contenido incluido en la página 8

Installation Instructions PLP Series 15° TILT ADJUSTMENT 0° To tilt the display 0° to 15° down, do the following: 1. Manually tilt the display 0° to 15° down into the desired position. 2. If desired, tighten the nut (see Figure 10) to increase 1. Adjust pitch the amount of tension needed to hold the mount in 2. If necessary, tighten the position set in Step 1. nut slightly to increase tension. NOTE:Tighten the nuts only to adjust the amount of tension needed to manually tilt and hold the mount i