Resumen del contenido incluido en la página 1
Installation Instructions / Warranty
Electronic
15180XX1
Electronic
15181XX1
Resumen del contenido incluido en la página 2
Hansgrohe Electronic Lavatory Faucet with Temperature Control 15180XX1 Hansgrohe Electronic Lavatory Faucet 15181XX1 Technical data Max. water pressure: 116 psi Recommended pressure: 14.5 - 7 psi Hot water temperature: max. 158 °F* Recommended hot water temperature: 10°F - 140°F* Rate of flow: 1.5 gpm @ 44 psi Automatic shutoff: after 35 seconds Hole size in mounting surface: 1 3/8“ Max. mounting surface thickness 1 1/8“ Requires standard 110V electrical outlet.** *please know and follow all a
Resumen del contenido incluido en la página 3
Installation Flush the hot and cold supplies thoroughly before installing this faucet. Place the faucet in the hole in the mounting surface (1). From beneath the sink, install the fiber washer, metal washer and mounting nut (). Install the adapters on the stops (3). Install the filters (4) and supply lines (5). Connect the transformer. Plug into the outlet. Use a cable tie to bundle excess cable. 3
Resumen del contenido incluido en la página 4
Turn the water on to the faucet (1). Peel the protective film from the sensor (). Wait 15 seconds, then put a hand in front of the sensor. The water should turn on automatically. Model 15180 only: Pivot the temperature control lever forward to make the water cooler. Model 15181 only: Turn the water off at the stops (1). Remove the set screw on the back of the faucet (). 4
Resumen del contenido incluido en la página 5
Pull the faucet housing off (1). Use a screwdriver to set the water temperature (). Turn the screw to the rear to make the water warmer, to the front to make it cooler. Replace the faucet housing. Tighten the set screw. Cleaning: Block the sensor for 5 seconds (1). This will turn the water off for approximately 75 seconds so that the sink may be cleaned (). 5
Resumen del contenido incluido en la página 6
Faucet Maintenance Reset the faucet: Remove the set screw with a .5 mm Allen wrench. Block the sensor for seconds. Wait 10 seconds (1), then replace the set screw (). 6
Resumen del contenido incluido en la página 7
Wait 15 seconds (3), then place a hand in front of the sensor (4). The water should turn on. Cleaning the filters and aerator If the flow of water is reduced, the filters and/or the aera- tor must be cleaned. To clean the aerator: Block the sensor for 5 seconds to temporarily shut off the water (1). Unscrew and remove the aerator. Flush any debris from the aerator at another faucet (). 7
Resumen del contenido incluido en la página 8
To clean the filters: Turn the water off at the stops (1). Disconnect the supply hoses from the adapters (). Pull the filters out and clean them. 8
Resumen del contenido incluido en la página 9
Replacement Parts 1 aerator 6788XXX solenoid valve 8854000 3 fixation set 781000 1 4 connection hose 6405000 5 back flow preventor cartridge 6 06000 6 electronics 605000 7 AC adapter 760000 8 transformer 768001 7 6 3 8 4 5
Resumen del contenido incluido en la página 10
Cleaning Recommendation for Hansgrohe Products Modern faucetry and shower products utilize a combination of materials to comply with the needs of the market with regard to design and functionality. To avoid damage, it is necessary to use some caution when cleaning. Damage caused by improper treatment is not covered under the Hansgrohe warranty. Cleaning Materials for Faucets and Showers • To remove lime scale, use only products made specifically for that purpose. Always follow the manufactur
Resumen del contenido incluido en la página 11
Limited Lifetime Consumer Warranty This product has been manufactured and tested to the highest quality standards by Hansgrohe, Inc. (“Hansgrohe”). This warranty is limited to Hansgrohe products which are purchased by a consumer in the United States after March 1, 16, and installed in either the United States or Canada. WHO IS COVERED BY THE WARRANTY This warranty extends to the original consumer purchaser only. This warranty is non-transferable. WHAT IS COVERED BY THE WARRANTY This warran
Resumen del contenido incluido en la página 12
TO OBTAIN WARRANTY PARTS OR INFORMATION Contact your Hansgrohe retailer, or contact Technical Service at: Hansgrohe Inc. 14 Bluegrass Lakes Parkway Alpharetta GA 30004 Toll-free (800) 334-0455. In requesting warranty service, you will need to provide 1. The sales receipt or other evidence of the date and place of purchase. . A description of the problem. 3. Delivery of the product or the defective part, postage prepaid and carefully packed and insured, to Hansgrohe Inc. 14 Bluegrass Lake
