Manual de instrucciones de GE Monogram ZDWI240WII

Resumen del contenido incluido en la página 1

Design Guide with
Installation
Instructions
Wine Chiller, Wine Reserve
and Beverage Center
monogram.com

Resumen del contenido incluido en la página 2

Safety Information BEFORE YOU BEGIN: WARNINGS: Read these instructions completely and carefully. • Use this appliance only for its intended purpose. • Immediately repair or replace electrical service cords IMPORTANT – Save these instructions that become frayed or damaged. for local inspector’s use. • Unplug the unit before cleaning or making repairs. • Repairs should be made by a qualified service IMPORTANT – Observe all governing codes technician. and ordinances. Note to Installer – Be sur

Resumen del contenido incluido en la página 3

Design Guide THE INSTALLATION SPACE (cont.) THE INSTALLATION SPACE Flush Installation Dim. A Filler panel or cleat to be set back even with front of case. CABINET CABINET Front edge of product case Front face 110° These products will fit flush to 120° adjacent cabinets when installed with a Dim. A-width filler panel or cleat. The filler panel should be recessed or set back behind NOTE: the door and even with the front Handle and handle edge of the product case. standoff depth is 1-3

Resumen del contenido incluido en la página 4

Design Guide PRODUCT CLEARANCES SIDE-BY-SIDE INSTALLATIONS The stainless steel wine chiller, wine reserve and Increase storage capacity by installing two Monogram beverage center is factory set for a 110° door swing. beverage centers, wine chillers or wine reserves together. Models that accept custom panels have a 95° door Or, for a complete refreshment center, install any two swing. of these units together. • A side-by-side installation requires at least a 47-1/2"- When installed in a co

Resumen del contenido incluido en la página 5

Installation Instructions TOOLS REQUIRED STAINING WOOD DRAWER FRONTS • #2 Phillips screwdriver The drawer fronts are unfinished cherry wood. During • Adjustable wrench use, oil from hands may accumulate and stain the wood. • The drawer fronts may be stained and sealed to PARTS SUPPLIED match adjacent cabinetry. The tinted glass will make • Monogram nameplate the stained wood appear darker. A true color match • Hardware for changing door swing can be seen only when the door is opened. • Opti

Resumen del contenido incluido en la página 6

Installation Instructions STEP 2 REVERSE DOOR SWING SKIP THIS STEP IF DOOR SWING SUITS THE INSTALLATION Install 3 Hinge Parts Included: Screws • Top left case hinge Remove • Bottom left case hinge Top Hinge • Left and right side decorative hinge cover • Decorative hinge screw hole cover ® • Torx driver bit Hinge Tools Required: Pin and • Phillips screwdriver Bracket • Electric drill Door Stop and Cam Riser Remove the door: • Flatten the shipping carton to use as a pad. • Remove the 2 screws a

Resumen del contenido incluido en la página 7

Installation Instructions STEP 3 LEVEL CUSTOM FRAME PANEL MODELS • Use an adjustable wrench to turn the leveling legs and Model ZDWI240WII and ZDBI240WII raise or lower the product. These models require a custom panel frame surrounding • Adjust carefully; the product should be level and plumb the glass. There are two options: the panel may be 29-3/4" with cabinetry, and should align with adjacent toekick or 30" high. A 30" panel requires a notch cut into the bottom height. of the panel t

Resumen del contenido incluido en la página 8

TEMPLATE FOR NAMEPLATE LOCATION To position nameplate: • Cut template along dotted line. • Hold or tape template behind glass door so that it is visible from the front side. • Remove backing from nameplate. • Place nameplate onto front side of door, matching illustration on the template. IMPORTANT: Nameplate must be placed on the opposite side of the door handle. Note: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local